Merge pull request #840 from justcallmekoko/develop

Merge develop into master
Merge pull request #839 from justcallmekoko/marauder_c5
2025-12-15 17:20:47 -08:00 · 2025-07-22 09:59:16 -04:00 · 2025-07-22 09:54:01 -04:00 · 2025-07-22 09:40:56 -04:00 · 2025-07-21 19:24:29 -04:00 · 2025-07-21 19:19:13 -04:00
56 changed files with 8664 additions and 2156 deletions
--- a/.github/workflows/build_parallel.yml
+++ b/.github/workflows/build_parallel.yml
@@ -17,19 +17,24 @@ jobs:
      fail-fast: false
      matrix:
        board:
-          - { name: "Flipper Zero WiFi Dev Board",  flag: "MARAUDER_FLIPPER",         fbqn: "esp32:esp32:esp32s2:PartitionScheme=min_spiffs,FlashSize=4M,PSRAM=enabled",  file_name: "flipper",                 tft: false, tft_file: "",                                   build_dir: "esp32s2", addr: "0x1000" }
-          - { name: "Flipper Zero Multi Board",     flag: "MARAUDER_FLIPPER",         fbqn: "esp32:esp32:esp32s3:PartitionScheme=min_spiffs,FlashSize=8M,PSRAM=enabled",  file_name: "multiboardS3",            tft: false, tft_file: "",                                   build_dir: "esp32s3", addr: "0x0" }
-          - { name: "OG Marauder",                  flag: "MARAUDER_V4",              fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                 file_name: "og",                      tft: true,  tft_file: "User_Setup_og_marauder.h",           build_dir: "d32",     addr: "0x1000" }
-          - { name: "Marauder v6",                  flag: "MARAUDER_V6",              fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                 file_name: "v6",                      tft: true,  tft_file: "User_Setup_og_marauder.h",           build_dir: "d32",     addr: "0x1000" }
-          - { name: "Marauder v6.1",                flag: "MARAUDER_V6_1",            fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                 file_name: "v6_1",                    tft: true,  tft_file: "User_Setup_og_marauder.h",           build_dir: "d32",     addr: "0x1000" }
-          - { name: "Marauder Kit",                 flag: "MARAUDER_KIT",             fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                 file_name: "kit",                     tft: true,  tft_file: "User_Setup_og_marauder.h",           build_dir: "d32",     addr: "0x1000" }
-          - { name: "Marauder Mini",                flag: "MARAUDER_MINI",            fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                 file_name: "mini",                    tft: true,  tft_file: "User_Setup_marauder_mini.h",         build_dir: "d32",     addr: "0x1000" }
-          - { name: "ESP32 LDDB",                   flag: "ESP32_LDDB",               fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                 file_name: "esp32_lddb",              tft: false, tft_file: "",                                   build_dir: "d32",     addr: "0x1000" }
-          - { name: "Marauder Dev Board Pro",       flag: "MARAUDER_DEV_BOARD_PRO",   fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                 file_name: "marauder_dev_board_pro",  tft: false, tft_file: "",                                   build_dir: "d32",     addr: "0x1000" }
-          - { name: "M5StickCPlus",                 flag: "MARAUDER_M5STICKC",        fbqn: "esp32:esp32:m5stick-c:PartitionScheme=min_spiffs",                           file_name: "m5stickc_plus",           tft: true,  tft_file: "User_Setup_marauder_m5stickc.h",     build_dir: "m5stick-c", addr: "0x1000" }
-          - { name: "M5StickCPlus 2",               flag: "MARAUDER_M5STICKCP2",      fbqn: "esp32:esp32:m5stick-c:PartitionScheme=min_spiffs",                           file_name: "m5stickc_plus2",          tft: true,  tft_file: "User_Setup_marauder_m5stickcp2.h",   build_dir: "m5stick-c", addr: "0x1000" }
-          - { name: "Rev Feather",                  flag: "MARAUDER_REV_FEATHER",     fbqn: "esp32:esp32:esp32s2:PartitionScheme=min_spiffs,FlashSize=4M,PSRAM=enabled",  file_name: "rev_feather",             tft: true,  tft_file: "User_Setup_marauder_rev_feather.h",  build_dir: "esp32s2", addr: "0x1000" }
-          - { name: "Marauder v7",                  flag: "MARAUDER_V7",              fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                 file_name: "marauder_v7",             tft: true,  tft_file: "User_Setup_dual_nrf24.h",            build_dir: "d32",     addr: "0x1000" }
+          - { name: "Flipper Zero WiFi Dev Board",   flag: "MARAUDER_FLIPPER",         fbqn: "esp32:esp32:esp32s2:PartitionScheme=min_spiffs,FlashSize=4M,PSRAM=enabled",                     file_name: "flipper",                 tft: false, tft_file: "",                                   build_dir: "esp32s2",                    addr: "0x1000" }
+          - { name: "Flipper Zero Multi Board S3",   flag: "MARAUDER_MULTIBOARD_S3",   fbqn: "esp32:esp32:esp32s3:PartitionScheme=min_spiffs,FlashSize=4M",                                   file_name: "multiboardS3",            tft: false, tft_file: "",                                   build_dir: "esp32s3",                    addr: "0x0" }
+          - { name: "OG Marauder",                   flag: "MARAUDER_V4",              fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                                    file_name: "og",                      tft: true,  tft_file: "User_Setup_og_marauder.h",           build_dir: "d32",                        addr: "0x1000" }
+          - { name: "Marauder v6",                   flag: "MARAUDER_V6",              fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                                    file_name: "v6",                      tft: true,  tft_file: "User_Setup_og_marauder.h",           build_dir: "d32",                        addr: "0x1000" }
+          - { name: "Marauder v6.1",                 flag: "MARAUDER_V6_1",            fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                                    file_name: "v6_1",                    tft: true,  tft_file: "User_Setup_og_marauder.h",           build_dir: "d32",                        addr: "0x1000" }
+          - { name: "Marauder Kit",                  flag: "MARAUDER_KIT",             fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                                    file_name: "kit",                     tft: true,  tft_file: "User_Setup_og_marauder.h",           build_dir: "d32",                        addr: "0x1000" }
+          - { name: "Marauder Mini",                 flag: "MARAUDER_MINI",            fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                                    file_name: "mini",                    tft: true,  tft_file: "User_Setup_marauder_mini.h",         build_dir: "d32",                        addr: "0x1000" }
+          - { name: "ESP32 LDDB",                    flag: "ESP32_LDDB",               fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                                    file_name: "esp32_lddb",              tft: false, tft_file: "",                                   build_dir: "d32",                        addr: "0x1000" }
+          - { name: "Marauder Dev Board Pro",        flag: "MARAUDER_DEV_BOARD_PRO",   fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                                    file_name: "marauder_dev_board_pro",  tft: false, tft_file: "",                                   build_dir: "d32",                        addr: "0x1000" }
+          - { name: "M5StickCPlus",                  flag: "MARAUDER_M5STICKC",        fbqn: "esp32:esp32:m5stick-c:PartitionScheme=min_spiffs",                                              file_name: "m5stickc_plus",           tft: true,  tft_file: "User_Setup_marauder_m5stickc.h",     build_dir: "m5stick-c",                  addr: "0x1000" }
+          - { name: "M5StickCPlus 2",                flag: "MARAUDER_M5STICKCP2",      fbqn: "esp32:esp32:m5stick-c:PartitionScheme=min_spiffs",                                              file_name: "m5stickc_plus2",          tft: true,  tft_file: "User_Setup_marauder_m5stickcp2.h",   build_dir: "m5stick-c",                  addr: "0x1000" }
+          - { name: "Rev Feather",                   flag: "MARAUDER_REV_FEATHER",     fbqn: "esp32:esp32:esp32s2:PartitionScheme=min_spiffs,FlashSize=4M,PSRAM=enabled",                     file_name: "rev_feather",             tft: true,  tft_file: "User_Setup_marauder_rev_feather.h",  build_dir: "esp32s2",                    addr: "0x1000" }
+          - { name: "Marauder v7",                   flag: "MARAUDER_V7",              fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                                    file_name: "marauder_v7",             tft: true,  tft_file: "User_Setup_dual_nrf24.h",            build_dir: "d32",                        addr: "0x1000" }
+          - { name: "Marauder CYD 2432S028",         flag: "MARAUDER_CYD_MICRO",       fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                                    file_name: "cyd_2432S028",            tft: true,  tft_file: "User_Setup_cyd_micro.h",             build_dir: "d32",                        addr: "0x1000" }
+          - { name: "Marauder CYD 2432S024 GUITION", flag: "MARAUDER_CYD_GUITION",     fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                                    file_name: "cyd_2432S024_guition",    tft: true,  tft_file: "User_Setup_cyd_guition.h",           build_dir: "d32",                        addr: "0x1000" }
+          - { name: "Marauder CYD 2432S028 2 USB",   flag: "MARAUDER_CYD_2USB",        fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                                    file_name: "cyd_2432S028_2usb",       tft: true,  tft_file: "User_Setup_cyd_2usb.h",              build_dir: "d32",                        addr: "0x1000" }
+          - { name: "Marauder v7.1",                 flag: "MARAUDER_V7_1",            fbqn: "esp32:esp32:dfrobot_firebeetle2_esp32e:FlashSize=16M,PartitionScheme=min_spiffs,PSRAM=enabled", file_name: "marauder_v7_1",           tft: true,  tft_file: "User_Setup_dual_nrf24.h",            build_dir: "dfrobot_firebeetle2_esp32e", addr: "0x1000" }
+          - { name: "M5Cardputer",                   flag: "MARAUDER_CARDPUTER",       fbqn: "esp32:esp32:esp32s3:PartitionScheme=min_spiffs,FlashSize=8M,PSRAM=disabled",                    file_name: "m5cardputer",             tft: true,  tft_file: "User_Setup_marauder_m5cardputer.h",  build_dir: "esp32s3",                    addr: "0x1000" }
          
    steps:
      - name: Checkout Code
@@ -65,6 +70,13 @@ jobs:
        run: |
          find /home/runner/.arduino15/packages/esp32/hardware/
          
+      - name: Install ESP32Ping
+        uses: actions/checkout@v2
+        with:
+          repository: marian-craciunescu/ESP32Ping
+          ref: 1.6
+          path: CustomESP32Ping
+          
      - name: Install AsyncTCP
        uses: actions/checkout@v2
        with:
@@ -92,6 +104,13 @@ jobs:
          repository: Bodmer/TFT_eSPI
          ref: V2.5.34
          path: CustomTFT_eSPI
+          
+      - name: Install XPT2046_Touchscreen
+        uses: actions/checkout@v2
+        with:
+          repository: PaulStoffregen/XPT2046_Touchscreen
+          ref: v1.4
+          path: CustomXPT2046_Touchscreen

      - name: Install lv_arduino
        uses: actions/checkout@v2
@@ -111,7 +130,7 @@ jobs:
        uses: actions/checkout@v2
        with:
          repository: h2zero/NimBLE-Arduino
-          ref: 1.3.5
+          ref: 1.3.8
          path: CustomNimBLE-Arduino

      - name: Install Adafruit_NeoPixel
--- a/.github/workflows/build_push.yml
+++ b/.github/workflows/build_push.yml
@@ -1,886 +0,0 @@
-name: Build and Push
-
-on:
-  workflow_dispatch:
-  pull_request:
-
-jobs:
-  # This workflow contains a single job called "build"
-  build:
-    name: Build Marauder Binaries
-    
-    runs-on: ubuntu-latest
-    
-    steps:
-      - name: Checkout Code
-        uses: actions/checkout@v3
-        
-#      - name: Install ESP32 Boards and Compile TestFile
-#        uses: ArminJo/arduino-test-compile@v3.2.1
-#        with:
-#          sketch-names: TestFile.ino
-#          arduino-board-fqbn: esp32:esp32:esp32s2
-#          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.10/package_esp32_dev_index.json
-          
-      - name: Install Arduino CLI
-        run: |
-          curl -fsSL https://raw.githubusercontent.com/arduino/arduino-cli/master/install.sh | sh
-          echo "/home/runner/work/ESP32Marauder/ESP32Marauder/bin" >> $GITHUB_PATH
-          export PATH=$PATH:/home/runner/work/ESP32Marauder/ESP32Marauder/bin
-          arduino-cli version
-
-      - name: Install Arduino-ESP32 Core v2.0.11
-        run: |
-          arduino-cli core update-index
-          arduino-cli core install esp32:esp32@2.0.11
-
-      - name: Verify Installed Cores
-        run: arduino-cli core list
-
-      - name: Build TestFile with ESP32 v2.0.11
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: TestFile.ino
-          arduino-board-fqbn: esp32:esp32:esp32s2
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-
-      - name: Verify Installed Cores Again
-        run: arduino-cli core list
-          
-      - name: Show Arduino dir structure
-        run: |
-          find /home/runner/.arduino15/packages/esp32/hardware/
-        
-#      - name: Pull arduino-esp32 v2.0.4
-#        uses: actions/checkout@v2
-#        with:
-#          repository: espressif/arduino-esp32
-#          ref: 2.0.4
-#          path: 2.0.4arduino-esp32
-          
-#      - name: Pull arduino-esp32 v2.0.10
-#        uses: actions/checkout@v2
-#        with:
-#          repository: espressif/arduino-esp32
-#          ref: 2.0.10
-#          path: 2.0.10
-          
-      - name: Install AsyncTCP
-        uses: actions/checkout@v2
-        with:
-          repository: me-no-dev/AsyncTCP
-          ref: master
-          path: CustomAsyncTCP
-          
-      - name: Install MicroNMEA
-        uses: actions/checkout@v2
-        with:
-          repository: stevemarple/MicroNMEA
-          ref: v2.0.6
-          path: CustomMicroNMEA
-          
-      - name: Install ESPAsyncWebServer
-        uses: actions/checkout@v2
-        with:
-          repository: bigbrodude6119/ESPAsyncWebServer
-          ref: master
-          path: CustomESPAsyncWebServer
-          
-      - name: Install TFT_eSPI
-        uses: actions/checkout@v2
-        with:
-          repository: Bodmer/TFT_eSPI
-          ref: V2.5.34
-          path: CustomTFT_eSPI
-
-      - name: Install lv_arduino
-        uses: actions/checkout@v2
-        with:
-          repository: lvgl/lv_arduino
-          ref: 3.0.0
-          path: Customlv_arduino
-
-      - name: Install JPEGDecoder
-        uses: actions/checkout@v2
-        with:
-          repository: Bodmer/JPEGDecoder
-          ref: 1.8.0
-          path: CustomJPEGDecoder
-
-      - name: Install NimBLE-Arduino
-        uses: actions/checkout@v2
-        with:
-          repository: h2zero/NimBLE-Arduino
-          ref: 1.3.5
-          path: CustomNimBLE-Arduino
-
-      - name: Install Adafruit_NeoPixel
-        uses: actions/checkout@v2
-        with:
-          repository: adafruit/Adafruit_NeoPixel
-          ref: 1.10.7
-          path: CustomAdafruit_NeoPixel
-
-      - name: Install ArduinoJson
-        uses: actions/checkout@v2
-        with:
-          repository: bblanchon/ArduinoJson
-          ref: v6.18.2
-          path: CustomArduinoJson
-
-      #- name: Install SwitchLib
-      #  uses: actions/checkout@v2
-      #  with:
-      #    repository: justcallmekoko/SwitchLib
-      #    ref: main
-      #    path: CustomSwitchLib
-          
-      - name: Install LinkedList
-        uses: actions/checkout@v2
-        with:
-          repository: ivanseidel/LinkedList
-          ref: v1.3.3
-          path: CustomLinkedList
-          
-      - name: Install EspSoftwareSerial
-        uses: actions/checkout@v2
-        with:
-          repository: plerup/espsoftwareserial
-          ref: 8.1.0
-          path: CustomEspSoftwareSerial
-          
-      - name: Install Adafruit_BusIO
-        uses: actions/checkout@v2
-        with:
-          repository: adafruit/Adafruit_BusIO
-          ref: 1.15.0
-          path: CustomAdafruit_BusIO
-          
-      - name: Install Adafruit_MAX1704X
-        uses: actions/checkout@v2
-        with:
-          repository: adafruit/Adafruit_MAX1704X
-          ref: 1.0.2
-          path: CustomAdafruit_MAX1704X
-          
-      #- name: Search for SD lib in arduino-esp32 v2.0.4
-      #  run: |
-      #    find /home/runner/work/ESP32Marauder/ESP32Marauder/2.0.4arduino-esp32 -name "SD"
-          
-      - name: Configure TFT_eSPI
-        run: |
-          rm -f CustomTFT_eSPI/User_Setup_Select.h
-          cp User_Setup_Select.h CustomTFT_eSPI/
-          cp User_Setup_marauder_mini.h CustomTFT_eSPI/
-          cp User_Setup_og_marauder.h CustomTFT_eSPI/
-          cp User_Setup_marauder_m5stickc.h CustomTFT_eSPI/
-          cp User_Setup_marauder_m5stickcp2.h CustomTFT_eSPI/
-          cp User_Setup_marauder_rev_feather.h CustomTFT_eSPI/
-          cp User_Setup_dual_nrf24.h CustomTFT_eSPI/
-          pwd
-          ls -la
-          ls -la CustomTFT_eSPI
-          
-      #- name: Place 2.0.10 for use
-      #  run: |
-      #    mkdir -p /home/runner/.arduino15/packages/esp32/hardware/esp32/
-      #    cp -R /home/runner/work/ESP32Marauder/ESP32Marauder/2.0.3 /home/runner/.arduino15/packages/esp32/hardware/esp32/2.0.3
-      #    ls -la /home/runner/.arduino15/packages/esp32/hardware/esp32/
-      #    echo Whoever made me have to do this can fuck off
-          
-      #- name: Replace arduino-esp32 v2.0.10 that was gloriously forced on us
-      #  run: |
-      #    rm -rf /home/runner/.arduino15/packages/esp32/hardware/esp32/2.0.10
-      #    cp -R /home/runner/work/ESP32Marauder/ESP32Marauder/2.0.3 /home/runner/.arduino15/packages/esp32/hardware/esp32/2.0.3
-      #    ls -la /home/runner/.arduino15/packages/esp32/hardware/esp32/
-      #    echo Whoever made me have to do this can fuck off
-          
-      #- name: Search for SD lib in arduino-esp32
-      #  run: |
-      #    find /home/runner/ -name "SD"
-          
-      #- name: Replace SD lib
-      #  run: |
-      #    rm -rf /home/runner/.arduino15/packages/esp32/hardware/esp32/2.0.10/libraries/SD
-      #    cp -R /home/runner/work/ESP32Marauder/ESP32Marauder/2.0.4arduino-esp32/libraries/SD /home/runner/.arduino15/packages/esp32/hardware/esp32/2.0.10/libraries/SD
-      #    ls -la /home/runner/.arduino15/packages/esp32/hardware/esp32/2.0.10/libraries/SD
-          
-      - name: Modify platform.txt
-        run: |
-          for i in $(find /home/runner/.arduino15/packages/esp32/hardware/esp32/ -name "platform.txt"); do
-            sed -i 's/compiler.c.elf.libs.esp32c3=/compiler.c.elf.libs.esp32c3=-zmuldefs /' "$i"
-            sed -i 's/compiler.c.elf.libs.esp32s3=/compiler.c.elf.libs.esp32s3=-zmuldefs /' "$i"
-            sed -i 's/compiler.c.elf.libs.esp32s2=/compiler.c.elf.libs.esp32s2=-zmuldefs /' "$i"
-            sed -i 's/compiler.c.elf.libs.esp32=/compiler.c.elf.libs.esp32=-zmuldefs /' "$i"
-            cat "$i" | grep compiler.c.elf.libs.esp32c3
-            cat "$i" | grep compiler.c.elf.libs.esp32s3
-            cat "$i" | grep compiler.c.elf.libs.esp32s2
-            cat "$i" | grep compiler.c.elf.libs.esp32
-          done
-          
-      - name: Configure configs.h for Flipper Zero WiFi Dev Board
-        run: |
-          sed -i 's/^  #define MARAUDER_REV_FEATHER/  \/\/#define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_M5STICKC/  \/\/#define MARAUDER_M5STICKC/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_MINI/  \/\/#define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V4/  \/\/#define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6/  \/\/#define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6_1/  \/\/#define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V7/  \/\/#define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_KIT/  \/\/#define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  \/\/#define MARAUDER_FLIPPER/  #define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  #define ESP32_LDDB/  \/\/#define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_DEV_BOARD_PRO/  \/\/#define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-                    
-      - name: Build Marauder for Flipper Zero WiFi Dev Board
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:esp32s2:PartitionScheme=min_spiffs,FlashSize=4M,PSRAM=enabled
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename Marauder Flipper bin
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.esp32s2/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.esp32s2/esp32_marauder.flipper.bin
-          
-      - name: Build Marauder for Flipper Zero Multi Board
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:esp32s3:PartitionScheme=min_spiffs,FlashSize=8M,PSRAM=enabled
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename Marauder Multi Board bin
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.esp32s3/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.esp32s3/esp32_marauder.multiboardS3.bin
-         
-      - name: Configure TFT_eSPI and configs.h for OG Marauder
-        run: |
-          pwd
-          find /home/runner/ -name "*TFT_eSPI*"     
-          sed -i 's/^#include <User_Setup_marauder_rev_feather.h>/\/\/#include <User_Setup_marauder_rev_feather.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h          
-          sed -i 's/^#include <User_Setup_marauder_mini.h>/\/\/#include <User_Setup_marauder_mini.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_marauder_m5stickc.h>/\/\/#include <User_Setup_marauder_m5stickc.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_dual_nrf24.h>/\/\/#include <User_Setup_dual_nrf24.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^\/\/#include <User_Setup_og_marauder.h>/#include <User_Setup_og_marauder.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^  #define MARAUDER_REV_FEATHER/  \/\/#define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_MINI/  \/\/#define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  \/\/#define MARAUDER_V4/  #define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6/  \/\/#define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6_1/  \/\/#define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V7/  \/\/#define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_KIT/  \/\/#define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_FLIPPER/  \/\/#define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  #define ESP32_LDDB/  \/\/#define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_DEV_BOARD_PRO/  \/\/#define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-          
-      - name: Build Marauder for OG Marauder
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:d32:PartitionScheme=min_spiffs
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename OG Marauder bin
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.og.bin
-          
-      - name: Configure TFT_eSPI and configs.h for Marauder v6
-        run: |
-          sed -i 's/^#include <User_Setup_marauder_rev_feather.h>/\/\/#include <User_Setup_marauder_rev_feather.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_marauder_mini.h>/\/\/#include <User_Setup_marauder_mini.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_marauder_m5stickc.h>/\/\/#include <User_Setup_marauder_m5stickc.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_dual_nrf24.h>/\/\/#include <User_Setup_dual_nrf24.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^\/\/#include <User_Setup_og_marauder.h>/#include <User_Setup_og_marauder.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^  #define MARAUDER_REV_FEATHER/  \/\/#define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_MINI/  \/\/#define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V4/  \/\/#define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  \/\/#define MARAUDER_V6/  #define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6_1/  \/\/#define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V7/  \/\/#define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_KIT/  \/\/#define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_FLIPPER/  \/\/#define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  #define ESP32_LDDB/  \/\/#define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_DEV_BOARD_PRO/  \/\/#define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-          
-      #- name: Build Marauder for v6 Marauder with arduino/compile-sketches
-      #  uses: arduino/compile-sketches@v1
-      #  with:
-      #    sketch-paths: esp32_marauder/esp32_marauder.ino
-      #    cli-compile-flags: |
-      #      - --warnings="none"
-      #      - --export-binaries
-      #    fqbn: esp32:esp32:d32:PartitionScheme=min_spiffs
-          
-      #- name: Show compiled arduino/compile-sketches v6 bin
-      #  run: |
-      #    find ~ -name "esp32_marauder.ino.bin"
-          
-      #- name: Rename v6_2 Marauder bin
-      #  run: |
-      #    mv ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.v6_2.bin
-          
-      - name: Build Marauder for v6 Marauder
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:d32:PartitionScheme=min_spiffs
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename v6 Marauder bin
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.v6.bin
-          
-      - name: Configure TFT_eSPI and configs.h for Marauder v6.1
-        run: |
-          sed -i 's/^  #define MARAUDER_REV_FEATHER/  \/\/#define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_MINI/  \/\/#define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V4/  \/\/#define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6/  \/\/#define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  \/\/#define MARAUDER_V6_1/  #define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V7/  \/\/#define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_KIT/  \/\/#define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_FLIPPER/  \/\/#define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  #define ESP32_LDDB/  \/\/#define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_DEV_BOARD_PRO/  \/\/#define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-          
-      - name: Build Marauder for v6.1 Marauder
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:d32:PartitionScheme=min_spiffs
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename v6 Marauder bin
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.v6_1.bin
-         
-      - name: Configure TFT_eSPI and configs.h for Marauder Kit
-        run: |
-          sed -i 's/^#include <User_Setup_marauder_mini.h>/\/\/#include <User_Setup_marauder_mini.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_marauder_m5stickc.h>/\/\/#include <User_Setup_marauder_m5stickc.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_dual_nrf24.h>/\/\/#include <User_Setup_dual_nrf24.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^\/\/#include <User_Setup_og_marauder.h>/#include <User_Setup_og_marauder.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^  #define MARAUDER_REV_FEATHER/  \/\/#define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_MINI/  \/\/#define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V4/  \/\/#define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6/  \/\/#define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6_1/  \/\/#define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V7/  \/\/#define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  \/\/#define MARAUDER_KIT/  #define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_FLIPPER/  \/\/#define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  #define ESP32_LDDB/  \/\/#define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_DEV_BOARD_PRO/  \/\/#define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-          
-      - name: Build Marauder for Marauder Kit
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:d32:PartitionScheme=min_spiffs
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename Marauder Kit bin
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.kit.bin
-          
-      - name: Configure TFT_eSPI and configs.h for Marauder Mini
-        run: |
-          sed -i 's/^\/\/#include <User_Setup_marauder_mini.h>/#include <User_Setup_marauder_mini.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_og_marauder.h>/\/\/#include <User_Setup_og_marauder.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_marauder_m5stickc.h>/\/\/#include <User_Setup_marauder_m5stickc.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_dual_nrf24.h>/\/\/#include <User_Setup_dual_nrf24.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^  #define MARAUDER_REV_FEATHER/  \/\/#define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  \/\/#define MARAUDER_MINI/  #define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V4/  \/\/#define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6/  \/\/#define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6_1/  \/\/#define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V7/  \/\/#define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_KIT/  \/\/#define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_FLIPPER/  \/\/#define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  #define ESP32_LDDB/  \/\/#define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_DEV_BOARD_PRO/  \/\/#define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-          
-      - name: Build Marauder for Marauder Mini
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:d32:PartitionScheme=min_spiffs
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename Marauder Mini bin
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.mini.bin
-          
-      - name: Configure TFT_eSPI and configs.h for ESP32 LDDB
-        run: |
-          sed -i 's/^  #define MARAUDER_REV_FEATHER/  \/\/#define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_MINI/  \/\/#define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V4/  \/\/#define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6/  \/\/#define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6_1/  \/\/#define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V7/  \/\/#define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_KIT/  \/\/#define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_FLIPPER/  \/\/#define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  \/\/#define ESP32_LDDB/  #define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_DEV_BOARD_PRO/  \/\/#define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-          
-      - name: Build Marauder for ESP32 LDDB
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:d32:PartitionScheme=min_spiffs
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename Marauder ESP32 LDDB bin
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.esp32_lddb.bin
-
-      - name: Configure TFT_eSPI and configs.h for Marauder Dev Board Pro
-        run: |
-          sed -i 's/^  #define MARAUDER_REV_FEATHER/  \/\/#define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_MINI/  \/\/#define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V4/  \/\/#define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6/  \/\/#define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6_1/  \/\/#define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V7/  \/\/#define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_KIT/  \/\/#define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_FLIPPER/  \/\/#define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  #define ESP32_LDDB/  \/\/#define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  \/\/#define MARAUDER_DEV_BOARD_PRO/  #define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-          
-      - name: Build Marauder for Marauder Dev Board Pro
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:d32:PartitionScheme=min_spiffs
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename Marauder for Marauder Dev Board Pro
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.marauder_dev_board_pro.bin
-          
-      - name: Configure TFT_eSPI and configs.h for Marauder M5StickC
-        run: |
-          pwd
-          find /home/runner/ -name "*TFT_eSPI*"          
-          sed -i 's/^#include <User_Setup_marauder_mini.h>/\/\/#include <User_Setup_marauder_mini.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^\/\/#include <User_Setup_marauder_m5stickc.h>/#include <User_Setup_marauder_m5stickc.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^  #define MARAUDER_REV_FEATHER/  \/\/#define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_MINI/  \/\/#define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V4/  \/\/#define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6/  \/\/#define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6_1/  \/\/#define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V7/  \/\/#define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_KIT/  \/\/#define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_FLIPPER/  \/\/#define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  #define ESP32_LDDB/  \/\/#define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_DEV_BOARD_PRO/  \/\/#define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-          sed -i 's/^  \/\/#define MARAUDER_M5STICKC /  #define MARAUDER_M5STICKC /' esp32_marauder/configs.h
-          
-      - name: Build Marauder for Marauder M5StickC
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:m5stick-c:PartitionScheme=min_spiffs
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename Marauder M5StickC bin
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.m5stick-c/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.m5stick-c/esp32_marauder.m5stickc_plus.bin
-
-      - name: Configure TFT_eSPI and configs.h for Marauder M5StickCP2
-        run: |
-          pwd
-          find /home/runner/ -name "*TFT_eSPI*"          
-          sed -i 's/^#include <User_Setup_marauder_mini.h>/\/\/#include <User_Setup_marauder_mini.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_marauder_m5stickc.h>/\/\/#include <User_Setup_marauder_m5stickc.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^\/\/#include <User_Setup_marauder_m5stickcp2.h>/#include <User_Setup_marauder_m5stickcp2.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^  #define MARAUDER_REV_FEATHER/  \/\/#define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_MINI/  \/\/#define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V4/  \/\/#define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6/  \/\/#define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6_1/  \/\/#define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V7/  \/\/#define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_KIT/  \/\/#define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_FLIPPER/  \/\/#define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  #define ESP32_LDDB/  \/\/#define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_DEV_BOARD_PRO/  \/\/#define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_M5STICKC /  \/\/#define MARAUDER_M5STICKC /' esp32_marauder/configs.h
-          sed -i 's/^  \/\/#define MARAUDER_M5STICKCP2/  #define MARAUDER_M5STICKCP2/' esp32_marauder/configs.h
-          
-      - name: Build Marauder for Marauder M5StickCP2
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:m5stick-c:PartitionScheme=min_spiffs
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename Marauder M5StickCP2 bin
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.m5stick-c/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.m5stick-c/esp32_marauder.m5stickc_plus2.bin
-
-      - name: Configure TFT_eSPI and configs.h for Marauder Rev Feather
-        run: |
-          pwd
-          find /home/runner/ -name "*TFT_eSPI*"          
-          sed -i 's/^\/\/#include <User_Setup_marauder_rev_feather.h>/#include <User_Setup_marauder_rev_feather.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_marauder_mini.h>/\/\/#include <User_Setup_marauder_mini.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_marauder_m5stickc.h>/\/\/#include <User_Setup_marauder_m5stickc.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_marauder_m5stickcp2.h>/\/\/#include <User_Setup_marauder_m5stickcp2.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^  \/\/#define MARAUDER_REV_FEATHER/  #define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_MINI/  \/\/#define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V4/  \/\/#define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6/  \/\/#define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6_1/  \/\/#define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V7/  \/\/#define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_KIT/  \/\/#define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_FLIPPER/  \/\/#define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  #define ESP32_LDDB/  \/\/#define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_DEV_BOARD_PRO/  \/\/#define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_M5STICKC /  \/\/#define MARAUDER_M5STICKC /' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_M5STICKCP2/  \/\/#define MARAUDER_M5STICKCP2/' esp32_marauder/configs.h
-          
-      - name: Build Marauder for Marauder Rev Feather
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:esp32s2:PartitionScheme=min_spiffs,FlashSize=4M,PSRAM=enabled
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename Marauder Marauder Rev Feather
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.esp32s2/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.esp32s2/esp32_marauder.rev_feather.bin
-          
-      - name: Configure TFT_eSPI and configs.h for Marauder v7
-        run: |
-          pwd
-          find /home/runner/ -name "*TFT_eSPI*"          
-          sed -i 's/^#include <User_Setup_marauder_rev_feather.h>/\/\/#include <User_Setup_marauder_rev_feather.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_marauder_mini.h>/\/\/#include <User_Setup_marauder_mini.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_marauder_m5stickc.h>/\/\/#include <User_Setup_marauder_m5stickc.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^\/\/#include <User_Setup_dual_nrf24.h>/#include <User_Setup_dual_nrf24.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^  #define MARAUDER_REV_FEATHER/  \/\/#define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_MINI/  \/\/#define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V4/  \/\/#define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6/  \/\/#define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6_1/  \/\/#define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  \/\/#define MARAUDER_V7/  #define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_KIT/  \/\/#define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_FLIPPER/  \/\/#define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  #define ESP32_LDDB/  \/\/#define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_DEV_BOARD_PRO/  \/\/#define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_M5STICKC/  \/\/#define MARAUDER_M5STICKC/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_M5STICKCP2/  \/\/#define MARAUDER_M5STICKCP2/' esp32_marauder/configs.h
-          
-      - name: Build Marauder for Marauder v7
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:d32:PartitionScheme=min_spiffs
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename Marauder Marauder v7
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.marauder_v7.bin
-
-      - name: Display finished bins
-        run: |
-          find ./esp32_marauder/build -name "*.bin"
-          
-      - name: 'Upload Flipper Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.flipper.bin
-          path: ./esp32_marauder/build/esp32.esp32.esp32s2/esp32_marauder.flipper.bin
-          retention-days: 5
-          
-      - name: 'Upload MultiboardS3 Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.multiboardS3.bin
-          path: ./esp32_marauder/build/esp32.esp32.esp32s3/esp32_marauder.multiboardS3.bin
-          retention-days: 5
-          
-      - name: 'Upload OG Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.og.bin
-          path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.og.bin
-          retention-days: 5
-          
-      - name: 'Upload v6 Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.v6.bin
-          path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.v6.bin
-          retention-days: 5
-          
-      - name: 'Upload v6_1 Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.v6_1.bin
-          path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.v6_1.bin
-          retention-days: 5
-          
-      - name: 'Upload Kit Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.kit.bin
-          path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.kit.bin
-          retention-days: 5
-          
-      - name: 'Upload Mini Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.mini.bin
-          path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.mini.bin
-          retention-days: 5
-          
-      - name: 'Upload ESP32 LDDB Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.esp32_lddb.bin
-          path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.esp32_lddb.bin
-          retention-days: 5
-          
-      - name: 'Upload Marauder Dev Board Pro Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.marauder_dev_board_pro.bin
-          path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.marauder_dev_board_pro.bin
-          retention-days: 5
-          
-      - name: 'Upload Marauder M5StickC Plus Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.m5stickc_plus.bin
-          path: ./esp32_marauder/build/esp32.esp32.m5stick-c/esp32_marauder.m5stickc_plus.bin
-          retention-days: 5
-
-      - name: 'Upload Marauder M5StickC Plus 2 Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.m5stickc_plus2.bin
-          path: ./esp32_marauder/build/esp32.esp32.m5stick-c/esp32_marauder.m5stickc_plus2.bin
-          retention-days: 5
-          
-      - name: 'Upload Rev Feather Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.rev_feather.bin
-          path: ./esp32_marauder/build/esp32.esp32.esp32s2/esp32_marauder.rev_feather.bin
-          retention-days: 5
-          
-      - name: 'Upload Marauder v7 Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.marauder_v7.bin
-          path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.marauder_v7.bin
-          retention-days: 5
-          
-      - name: Create Release
-        id: create_release
-        uses: actions/create-release@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          tag_name: ${{ github.ref }}
-          release_name: Release ${{ github.ref }}
-          draft: true
-          prerelease: false
-        if: github.event_name != 'pull_request'
-          
-      - name: Upload Flipper Asset
-        id: upload-flipper-release-asset 
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.esp32s2/esp32_marauder.flipper.bin
-          asset_name: esp32_marauder.flipper.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-          
-      - name: Upload MultiboardS3 Asset
-        id: upload-multiboardS3-release-asset 
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.esp32s3/esp32_marauder.multiboardS3.bin
-          asset_name: esp32_marauder.multiboardS3.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-          
-      - name: Upload OG Asset
-        id: upload-og-release-asset 
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.og.bin
-          asset_name: esp32_marauder.og.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-          
-      - name: Upload v6 Asset
-        id: upload-v6-release-asset 
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.v6.bin
-          asset_name: esp32_marauder.v6.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-        
-      - name: Upload v6_1 Asset
-        id: upload-v6-1-release-asset 
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.v6_1.bin
-          asset_name: esp32_marauder.v6_1.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-          
-      - name: Upload Kit Asset
-        id: upload-kit-release-asset 
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.kit.bin
-          asset_name: esp32_marauder.kit.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-          
-      - name: Upload Mini Asset
-        id: upload-mini-release-asset 
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.mini.bin
-          asset_name: esp32_marauder.mini.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-          
-      - name: Upload ESP32 LDDB Asset
-        id: upload-esp32-lddb-release-asset 
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.esp32_lddb.bin
-          asset_name: esp32_marauder.esp32_lddb.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-          
-      - name: Upload Marauder Dev Board Pro Asset
-        id: upload-marauder-dev-board-pro-release-asset
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.marauder_dev_board_pro.bin
-          asset_name: esp32_marauder.marauder_dev_board_pro.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-        
-      - name: Upload Marauder M5StickC Plus Asset
-        id: upload-m5stickc-plus-release-asset 
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.m5stick-c/esp32_marauder.m5stickc_plus.bin
-          asset_name: esp32_marauder.m5stickc_plus.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-
-      - name: Upload Marauder M5StickC Plus 2 Asset
-        id: upload-m5stickc-plus2-release-asset 
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.m5stick-c/esp32_marauder.m5stickc_plus2.bin
-          asset_name: esp32_marauder.m5stickc_plus2.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-
-      - name: Upload Rev Feather Asset
-        id: upload-rev-feather-release-asset 
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.esp32s2/esp32_marauder.rev_feather.bin
-          asset_name: esp32_marauder.rev_feather.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-        
-      - name: Upload Marauder v7 Asset
-        id: upload-marauder-v7-release-asset
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.marauder_v7.bin
-          asset_name: esp32_marauder.marauder_v7.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
--- a/C5_Py_Flasher/bins/bootloader.bin
+++ b/C5_Py_Flasher/bins/bootloader.bin
--- a/C5_Py_Flasher/bins/esp32_marauder_v1_8_1_20250722_esp32c5_devkit.bin
+++ b/C5_Py_Flasher/bins/esp32_marauder_v1_8_1_20250722_esp32c5_devkit.bin
--- a/C5_Py_Flasher/bins/partitions.bin
+++ b/C5_Py_Flasher/bins/partitions.bin
--- a/C5_Py_Flasher/c5_flasher.py
+++ b/C5_Py_Flasher/c5_flasher.py
@@ -0,0 +1,164 @@
+# === ESP32-C5 Auto Flasher Script By: AWOK ===
+
+import sys
+import subprocess
+import os
+import platform   # Placeholder for possible OS checks
+import glob
+import time
+import shutil
+import argparse
+
+def ensure_package(pkg):
+    try:
+        __import__(pkg if pkg != 'gitpython' else 'git')
+    except ImportError:
+        print(f"Installing missing package: {pkg}")
+        subprocess.check_call([sys.executable, '-m', 'pip', 'install', '--upgrade', pkg])
+
+try:
+    import serial.tools.list_ports
+except ImportError:
+    ensure_package('pyserial')
+try:
+    import esptool
+except ImportError:
+    ensure_package('esptool')
+try:
+    from colorama import Fore, Style
+except ImportError:
+    ensure_package('colorama')
+
+# Dependency check and install if needed
+REQUIRED_PACKAGES = [
+    'pyserial',
+    'esptool',
+    'colorama'
+]
+
+def ensure_requirements():
+    for pkg in REQUIRED_PACKAGES:
+        ensure_package(pkg)
+ensure_requirements()
+
+# Finds the first file from a list of possible names in the bins folder
+def find_file(name_options, bins_dir):
+    for name in name_options:
+        files = glob.glob(os.path.join(bins_dir, name))
+        if files:
+            return files[0]
+    return None
+
+def main():
+    parser = argparse.ArgumentParser(description="ESP32-C5 Auto Flasher (bins subdir)")
+    parser.parse_args()
+
+    bins_dir = os.path.join(os.path.dirname(__file__), 'bins')
+    if not os.path.isdir(bins_dir):
+        print(Fore.RED + f"Bins directory not found: {bins_dir}\nPlease create a 'bins' folder with your .bin files." + Style.RESET_ALL)
+        exit(1)
+
+    # Logo and splash, both centered and purple
+    terminal_width = shutil.get_terminal_size((100, 20)).columns
+    def center(text): return text.center(terminal_width)
+    logo_lines = [
+        "                                            @@@@@@                              ",
+        "                                @@@@@@@@  @@@@@ @@@@                            ",
+        "                               @@@    @@@@@@@     @@@     @@@@@@@@              ",
+        "                    @@@@@@@@@@@@@      @@@@@       @@@  @@@@    @@@             ",
+        "                   @@@      @@@@@       @@@         @@@@@@       @@@            ",
+        "                  @@@         @@@        @@         @@@@         @@@            ",
+        "         @@@@@@@@@@@@          @@        @          @@@         @@@     @@      ",
+        "        @@@     @@@@@           @@           @@@    @@          @@@@@@@@@@@@@@  ",
+        "       @@@         @@@           @@          @@@               @@@@@        @@@@",
+        "       @@@           @@                     @@@@              @@@            @@@",
+        "      @@@@@            @@                   @@@@                             @@@",
+        "   @@@@@@  @@                @@         @   @@@                            @@@@ ",
+        "  @@@                         @@       @@         @                     @@@@@@  ",
+        " @@@                           @@     @@@        @@            @@@@@@@@@@@@@@@  ",
+        "@@@       @@@@      @          @@@@  @@@@@     @@@        @      @@@@  @@@ @@@  ",
+        "@@@       @@@@@@@    @@@       @@@@@@@@@@@@@@@@@@@       @@        @@@ @@@      ",
+        "@@@        @@@@@ @@@  @@@@@  @@@@ @@@@  @@@@@@@@@@      @@@@        @@@         ",
+        "@@@@            @@@@@@@@@@@@@@@@  @@@   @@@ @@  @@@@@@@@@@@@         @@@        ",
+        " @@@@          @@@@@@@@@@@@@@@@   @@@       @@   @@@@@@@@@@@@        @@@        ",
+        "  @@@@@@     @@@@@   @@@     @@    @               @@  @@  @@@@    @@@@         ",
+        "   @@@@@@@@@@@@@     @@@     @@                    @@  @@   @@@@@@@@@@@         ",
+        "   @@@@@@@@@@@@      @@@     @@                   @@@  @     @@@@@@@@           ",
+        "        @@  @@                                    @@@        @@  @@@            ",
+        "        @   @@                                               @@  @@@            ",
+        "           @@@                                                   @@@            ",
+        "           @@@                                                                  ",
+        ""
+    ]
+    splash_lines = [
+        "--  ESP32 C5 Flasher --",
+        "By AWOK",
+        "Inspired from LordSkeletonMans ESP32 FZEasyFlasher",
+        "Shout out to JCMK for the inspiration on setting up the C5",
+        ""
+    ]
+    print(Fore.MAGENTA + "\n" + "\n".join(center(line) for line in logo_lines + splash_lines) + Style.RESET_ALL)
+
+    # Wait for ESP32 device to show up as a new serial port
+    existing_ports = set([port.device for port in serial.tools.list_ports.comports()])
+    print(Fore.YELLOW + "Waiting for ESP32-C5 device to be connected..." + Style.RESET_ALL)
+    while True:
+        current_ports = set([port.device for port in serial.tools.list_ports.comports()])
+        new_ports = current_ports - existing_ports
+        if new_ports:
+            serial_port = new_ports.pop()
+            break
+        time.sleep(0.5)
+    print(Fore.GREEN + f"Detected ESP32-C5 on port: {serial_port}" + Style.RESET_ALL)
+
+    # Find bin files for each firmware component
+    bootloader = find_file(['bootloader.bin'], bins_dir)
+    partitions = find_file(['partition-table.bin', 'partitions.bin'], bins_dir)
+    ota_data = find_file(['ota_data_initial.bin'], bins_dir)
+
+    # Main firmware: largest bin in the folder that's not bootloader, partition, or OTA
+    all_bins = glob.glob(os.path.join(bins_dir, "*.bin"))
+    exclude = {bootloader, partitions, ota_data}
+    firmware_bins = [f for f in all_bins if f not in exclude and os.path.isfile(f)]
+    if not firmware_bins:
+        print(Fore.RED + "No application firmware .bin file found in the 'bins' folder!" + Style.RESET_ALL)
+        exit(1)
+    app_bin = max(firmware_bins, key=lambda f: os.path.getsize(f))
+
+    # Print summary, ask for confirmation before flashing
+    print(Fore.CYAN + f"\nBootloader:   {bootloader or 'NOT FOUND'}")
+    print(f"Partitions:   {partitions or 'NOT FOUND'}")
+    print(f"OTA Data:     {ota_data or 'NOT FOUND'}")
+    print(f"App (main):   {app_bin}\n" + Style.RESET_ALL)
+    if not (bootloader and partitions):
+        print(Fore.RED + "Missing bootloader or partition table. Both are required for a complete flash!" + Style.RESET_ALL)
+        exit(1)
+    confirm = input(Fore.YELLOW + "Ready to flash these files to ESP32-C5? (y/N): " + Style.RESET_ALL)
+    if confirm.strip().lower() != 'y':
+        print("Aborting.")
+        exit(0)
+
+    # Flash using esptool, with offsets for C5
+    esptool_args = [
+        '--chip', 'esp32c5',
+        '--port', serial_port,
+        '--baud', '921600',
+        '--before', 'default_reset',
+        '--after', 'hard_reset',
+        'write_flash', '-z',
+        '0x2000', bootloader,
+        '0x8000', partitions,
+    ]
+    if ota_data:
+        esptool_args += ['0xd000', ota_data]
+    esptool_args += ['0x10000', app_bin]
+
+    print(Fore.YELLOW + "Flashing ESP32-C5 with bootloader, partition table, and application..." + Style.RESET_ALL)
+    try:
+        esptool.main(esptool_args)
+        print(Fore.GREEN + "Flashing complete!" + Style.RESET_ALL)
+    except Exception as e:
+        print(Fore.RED + f"Flashing failed: {e}" + Style.RESET_ALL)
+
+if __name__ == "__main__":
+    main()
--- a/PCBs/FlipperZero/WiFi-Devboard-Pro/WiFi-Devboard-Pro-backups/WiFi-Devboard-Pro-2022-12-13_161912.zip
+++ b/PCBs/FlipperZero/WiFi-Devboard-Pro/WiFi-Devboard-Pro-backups/WiFi-Devboard-Pro-2022-12-13_161912.zip
--- a/PCBs/FlipperZero/WiFi-Devboard-Pro/WiFi-Devboard-Pro-backups/WiFi-Devboard-Pro-2022-12-14_175854.zip
+++ b/PCBs/FlipperZero/WiFi-Devboard-Pro/WiFi-Devboard-Pro-backups/WiFi-Devboard-Pro-2022-12-14_175854.zip
--- a/PCBs/FlipperZero/WiFi-Devboard-Pro/WiFi-Devboard-Pro-backups/WiFi-Devboard-Pro-2022-12-14_181008.zip
+++ b/PCBs/FlipperZero/WiFi-Devboard-Pro/WiFi-Devboard-Pro-backups/WiFi-Devboard-Pro-2022-12-14_181008.zip
--- a/PCBs/FlipperZero/WiFi-Devboard-Pro/WiFi-Devboard-Pro-backups/WiFi-Devboard-Pro-2025-03-26_155226.zip
+++ b/PCBs/FlipperZero/WiFi-Devboard-Pro/WiFi-Devboard-Pro-backups/WiFi-Devboard-Pro-2025-03-26_155226.zip
--- a/PCBs/FlipperZero/WiFi-Devboard-Pro/WiFi-Devboard-Pro-backups/WiFi-Devboard-Pro-2025-05-28_160712.zip
+++ b/PCBs/FlipperZero/WiFi-Devboard-Pro/WiFi-Devboard-Pro-backups/WiFi-Devboard-Pro-2025-05-28_160712.zip
--- a/PCBs/FlipperZero/WiFi-Devboard-Pro/WiFi-Devboard-Pro-backups/WiFi-Devboard-Pro-2025-05-28_182343.zip
+++ b/PCBs/FlipperZero/WiFi-Devboard-Pro/WiFi-Devboard-Pro-backups/WiFi-Devboard-Pro-2025-05-28_182343.zip
--- a/README.md
+++ b/README.md
@@ -4,7 +4,7 @@
 <!---Shields/Badges https://shields.io/--->

 # ESP32 Marauder
-<p align="center"><img alt="Marauder logo" src="https://github.com/justcallmekoko/ESP32Marauder/blob/master/pictures/marauder3L.jpg?raw=true" width="300"></p>
+<p align="center"><img alt="Marauder logo" src="https://github.com/justcallmekoko/ESP32Marauder/blob/master/pictures/marauder_skull_patch_04_full_final.png?raw=true" width="300"></p>
 <p align="center">
  <b>A suite of WiFi/Bluetooth offensive and defensive tools for the ESP32</b>
  <br><br>
--- a/User_Setup_Select.h
+++ b/User_Setup_Select.h
@@ -30,6 +30,11 @@
 //#include <User_Setup_pocket_sdr.h>
 //#include <User_Setup_dual_nrf24.h>
 //#include <User_Setup_pocket_sdr_2.h>
+//#include <User_Setup_pocket_sdr_3.h>
+//#include <User_Setup_cyd_micro.h>
+//#include <User_Setup_cyd_guition.h>
+//#include <User_Setup_cyd_2usb.h>
+//#include <User_Setup_marauder_m5cardputer.h>

 //#include <User_Setups/Setup1_ILI9341.h>  // Setup file configured for my ILI9341
 //#include <User_Setups/Setup2_ST7735.h>   // Setup file configured for my ST7735
--- a/User_Setup_cyd_2usb.h
+++ b/User_Setup_cyd_2usb.h
@@ -0,0 +1,316 @@
+//                            USER DEFINED SETTINGS
+//   Set driver type, fonts to be loaded, pins used and SPI control method etc
+//
+//   See the User_Setup_Select.h file if you wish to be able to define multiple
+//   setups and then easily select which setup file is used by the compiler.
+//
+//   If this file is edited correctly then all the library example sketches should
+//   run without the need to make any more changes for a particular hardware setup!
+//   Note that some sketches are designed for a particular TFT pixel width/height
+
+
+// ##################################################################################
+//
+// Section 1. Call up the right driver file and any options for it
+//
+// ##################################################################################
+
+// Display type -  only define if RPi display
+//#define RPI_DRIVER
+
+// Only define one driver, the other ones must be commented out
+//#define ILI9341_DRIVER // OG Marauder
+//#define ST7735_DRIVER    // Marauder Mini  // Define additional parameters below for this display
+//#define ILI9163_DRIVER     // Define additional parameters below for this display
+//#define S6D02A1_DRIVER
+//#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
+//#define HX8357D_DRIVER
+//#define ILI9481_DRIVER
+//#define ILI9486_DRIVER
+//#define ILI9488_DRIVER     // WARNING: Do not connect ILI9488 display SDO to MISO if other devices share the SPI bus (TFT SDO does NOT tristate when CS is high)
+#define ST7789_DRIVER      // Full configuration option, define additional parameters below for this display
+//#define ST7789_2_DRIVER    // Minimal configuration option, define additional parameters below for this display
+//#define R61581_DRIVER
+//#define RM68140_DRIVER
+//#define ST7796_DRIVER
+
+// Some displays support SPI reads via the MISO pin, other displays have a single
+// bi-directional SDA pin and the library will try to read this via the MOSI line.
+// To use the SDA line for reading data from the TFT uncomment the following line:
+
+// #define TFT_SDA_READ      // This option is for ESP32 ONLY, tested with ST7789 display only
+
+// For ST7789 and ILI9341 ONLY, define the colour order IF the blue and red are swapped on your display
+// Try ONE option at a time to find the correct colour order for your display
+
+//  #define TFT_RGB_ORDER TFT_RGB  // Colour order Red-Green-Blue
+  #define TFT_RGB_ORDER TFT_BGR  // Colour order Blue-Green-Red
+
+// For M5Stack ESP32 module with integrated ILI9341 display ONLY, remove // in line below
+
+// #define M5STACK
+
+// For ST7789, ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation
+// #define TFT_WIDTH  80
+// #define TFT_WIDTH  128 // Marauder Mini
+ #define TFT_WIDTH  240 // ST7789 240 x 240 and 240 x 320
+// #define TFT_HEIGHT 160
+// #define TFT_HEIGHT 128 // Marauder Mini
+// #define TFT_HEIGHT 240 // ST7789 240 x 240
+ #define TFT_HEIGHT 320 // ST7789 240 x 320
+
+// For ST7735 ONLY, define the type of display, originally this was based on the
+// colour of the tab on the screen protector film but this is not always true, so try
+// out the different options below if the screen does not display graphics correctly,
+// e.g. colours wrong, mirror images, or tray pixels at the edges.
+// Comment out ALL BUT ONE of these options for a ST7735 display driver, save this
+// this User_Setup file, then rebuild and upload the sketch to the board again:
+
+// #define ST7735_INITB
+// #define ST7735_GREENTAB
+// #define ST7735_GREENTAB2
+// #define ST7735_GREENTAB3
+// #define ST7735_GREENTAB128    // For 128 x 128 display
+// #define ST7735_GREENTAB160x80 // For 160 x 80 display (BGR, inverted, 26 offset)
+// #define ST7735_REDTAB
+// #define ST7735_BLACKTAB
+// #define ST7735_REDTAB160x80   // For 160 x 80 display with 24 pixel offset
+
+// If colours are inverted (white shows as black) then uncomment one of the next
+// 2 lines try both options, one of the options should correct the inversion.
+
+// #define TFT_INVERSION_ON
+ #define TFT_INVERSION_OFF
+
+// If a backlight control signal is available then define the TFT_BL pin in Section 2
+// below. The backlight will be turned ON when tft.begin() is called, but the library
+// needs to know if the LEDs are ON with the pin HIGH or LOW. If the LEDs are to be
+// driven with a PWM signal or turned OFF/ON then this must be handled by the user
+// sketch. e.g. with digitalWrite(TFT_BL, LOW);
+
+// #define TFT_BACKLIGHT_ON LOW  // HIGH or LOW are options
+
+// ##################################################################################
+//
+// Section 2. Define the pins that are used to interface with the display here
+//
+// ##################################################################################
+
+// We must use hardware SPI, a minimum of 3 GPIO pins is needed.
+// Typical setup for ESP8266 NodeMCU ESP-12 is :
+//
+// Display SDO/MISO  to NodeMCU pin D6 (or leave disconnected if not reading TFT)
+// Display LED       to NodeMCU pin VIN (or 5V, see below)
+// Display SCK       to NodeMCU pin D5
+// Display SDI/MOSI  to NodeMCU pin D7
+// Display DC (RS/AO)to NodeMCU pin D3
+// Display RESET     to NodeMCU pin D4 (or RST, see below)
+// Display CS        to NodeMCU pin D8 (or GND, see below)
+// Display GND       to NodeMCU pin GND (0V)
+// Display VCC       to NodeMCU 5V or 3.3V
+//
+// The TFT RESET pin can be connected to the NodeMCU RST pin or 3.3V to free up a control pin
+//
+// The DC (Data Command) pin may be labeled AO or RS (Register Select)
+//
+// With some displays such as the ILI9341 the TFT CS pin can be connected to GND if no more
+// SPI devices (e.g. an SD Card) are connected, in this case comment out the #define TFT_CS
+// line below so it is NOT defined. Other displays such at the ST7735 require the TFT CS pin
+// to be toggled during setup, so in these cases the TFT_CS line must be defined and connected.
+//
+// The NodeMCU D0 pin can be used for RST
+//
+//
+// Note: only some versions of the NodeMCU provide the USB 5V on the VIN pin
+// If 5V is not available at a pin you can use 3.3V but backlight brightness
+// will be lower.
+
+
+// ###### EDIT THE PIN NUMBERS IN THE LINES FOLLOWING TO SUIT YOUR ESP8266 SETUP ######
+
+// For NodeMCU - use pin numbers in the form PIN_Dx where Dx is the NodeMCU pin designation
+//#define TFT_CS   PIN_D8  // Chip select control pin D8
+//#define TFT_DC   PIN_D3  // Data Command control pin
+//#define TFT_RST  PIN_D4  // Reset pin (could connect to NodeMCU RST, see next line)
+//#define TFT_RST  -1    // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
+
+//#define TFT_BL PIN_D1  // LED back-light (only for ST7789 with backlight control pin)
+
+//#define TOUCH_CS PIN_D2     // Chip select pin (T_CS) of touch screen
+
+//#define TFT_WR PIN_D2       // Write strobe for modified Raspberry Pi TFT only
+
+
+// ######  FOR ESP8266 OVERLAP MODE EDIT THE PIN NUMBERS IN THE FOLLOWING LINES  ######
+
+// Overlap mode shares the ESP8266 FLASH SPI bus with the TFT so has a performance impact
+// but saves pins for other functions. It is best not to connect MISO as some displays
+// do not tristate that line wjen chip select is high!
+// On NodeMCU 1.0 SD0=MISO, SD1=MOSI, CLK=SCLK to connect to TFT in overlap mode
+// On NodeMCU V3  S0 =MISO, S1 =MOSI, S2 =SCLK
+// In ESP8266 overlap mode the following must be defined
+
+//#define TFT_SPI_OVERLAP
+
+// In ESP8266 overlap mode the TFT chip select MUST connect to pin D3
+//#define TFT_CS   PIN_D3
+//#define TFT_DC   PIN_D5  // Data Command control pin
+//#define TFT_RST  PIN_D4  // Reset pin (could connect to NodeMCU RST, see next line)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
+
+
+// ###### EDIT THE PIN NUMBERS IN THE LINES FOLLOWING TO SUIT YOUR ESP32 SETUP   ######
+
+// For ESP32 Dev board (only tested with ILI9341 display)
+// The hardware SPI can be mapped to any pins
+
+// Marauder Mini
+/*
+#define TFT_CS   17  // Chip select control pin D8
+#define TFT_DC   16  // Data Command control pin
+#define TFT_RST  5  // Reset pin (could connect to NodeMCU RST, see next line)
+//#define TFT_MISO 19
+//#define TFT_MOSI 23
+//#define TFT_SCLK 18
+//#define TFT_BL   32
+*/
+
+// ESP32 Marauder 
+#define TFT_MISO 12
+#define TFT_MOSI 13
+#define TFT_SCLK 14
+#define TFT_CS   15  // Chip select control pin
+#define TFT_DC   2  // Data Command control pin
+#define TFT_RST   -1  // Reset pin (could connect to RST pin)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if display RESET is connected to ESP32 board RST
+
+#define TFT_BL   21  // LED back-light (only for ST7789 with backlight control pin)
+
+#define TOUCH_CS   33     // Chip select pin (T_CS) of touch screen
+
+/////////////////////////////
+
+// ESP32 Centauri
+/*
+#define TFT_MISO 19
+#define TFT_MOSI 23
+#define TFT_SCLK 18
+#define TFT_CS   27  // Chip select control pin
+#define TFT_DC   26  // Data Command control pin
+#define TFT_RST   5  // Reset pin (could connect to RST pin)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if display RESET is connected to ESP32 board RST
+
+#define TFT_BL   32  // LED back-light (only for ST7789 with backlight control pin)
+
+#define TOUCH_CS 21     // Chip select pin (T_CS) of touch screen
+*/
+/////////////////////////////
+
+//#define TFT_WR 22    // Write strobe for modified Raspberry Pi TFT only
+
+// For the M5Stack module use these #define lines
+//#define TFT_MISO 19
+//#define TFT_MOSI 23
+//#define TFT_SCLK 18
+//#define TFT_CS   14  // Chip select control pin
+//#define TFT_DC   27  // Data Command control pin
+//#define TFT_RST  33  // Reset pin (could connect to Arduino RESET pin)
+//#define TFT_BL   32  // LED back-light (required for M5Stack)
+
+// ######       EDIT THE PINs BELOW TO SUIT YOUR ESP32 PARALLEL TFT SETUP        ######
+
+// The library supports 8 bit parallel TFTs with the ESP32, the pin
+// selection below is compatible with ESP32 boards in UNO format.
+// Wemos D32 boards need to be modified, see diagram in Tools folder.
+// Only ILI9481 and ILI9341 based displays have been tested!
+
+// Parallel bus is only supported on ESP32
+// Uncomment line below to use ESP32 Parallel interface instead of SPI
+
+//#define ESP32_PARALLEL
+
+// The ESP32 and TFT the pins used for testing are:
+//#define TFT_CS   33  // Chip select control pin (library pulls permanently low
+//#define TFT_DC   15  // Data Command control pin - must use a pin in the range 0-31
+//#define TFT_RST  32  // Reset pin, toggles on startup
+
+//#define TFT_WR    4  // Write strobe control pin - must use a pin in the range 0-31
+//#define TFT_RD    2  // Read strobe control pin
+
+//#define TFT_D0   12  // Must use pins in the range 0-31 for the data bus
+//#define TFT_D1   13  // so a single register write sets/clears all bits.
+//#define TFT_D2   26  // Pins can be randomly assigned, this does not affect
+//#define TFT_D3   25  // TFT screen update performance.
+//#define TFT_D4   17
+//#define TFT_D5   16
+//#define TFT_D6   27
+//#define TFT_D7   14
+
+
+// ##################################################################################
+//
+// Section 3. Define the fonts that are to be used here
+//
+// ##################################################################################
+
+// Comment out the #defines below with // to stop that font being loaded
+// The ESP8366 and ESP32 have plenty of memory so commenting out fonts is not
+// normally necessary. If all fonts are loaded the extra FLASH space required is
+// about 17Kbytes. To save FLASH space only enable the fonts you need!
+
+#define LOAD_GLCD   // Font 1. Original Adafruit 8 pixel font needs ~1820 bytes in FLASH
+#define LOAD_FONT2  // Font 2. Small 16 pixel high font, needs ~3534 bytes in FLASH, 96 characters
+#define LOAD_FONT4  // Font 4. Medium 26 pixel high font, needs ~5848 bytes in FLASH, 96 characters
+#define LOAD_FONT6  // Font 6. Large 48 pixel font, needs ~2666 bytes in FLASH, only characters 1234567890:-.apm
+#define LOAD_FONT7  // Font 7. 7 segment 48 pixel font, needs ~2438 bytes in FLASH, only characters 1234567890:-.
+#define LOAD_FONT8  // Font 8. Large 75 pixel font needs ~3256 bytes in FLASH, only characters 1234567890:-.
+//#define LOAD_FONT8N // Font 8. Alternative to Font 8 above, slightly narrower, so 3 digits fit a 160 pixel TFT
+#define LOAD_GFXFF  // FreeFonts. Include access to the 48 Adafruit_GFX free fonts FF1 to FF48 and custom fonts
+
+// Comment out the #define below to stop the SPIFFS filing system and smooth font code being loaded
+// this will save ~20kbytes of FLASH
+#define SMOOTH_FONT
+
+
+// ##################################################################################
+//
+// Section 4. Other options
+//
+// ##################################################################################
+
+// Define the SPI clock frequency, this affects the graphics rendering speed. Too
+// fast and the TFT driver will not keep up and display corruption appears.
+// With an ILI9341 display 40MHz works OK, 80MHz sometimes fails
+// With a ST7735 display more than 27MHz may not work (spurious pixels and lines)
+// With an ILI9163 display 27 MHz works OK.
+
+// #define SPI_FREQUENCY   1000000
+//#define SPI_FREQUENCY   5000000
+// #define SPI_FREQUENCY  10000000
+// #define SPI_FREQUENCY  20000000
+#define SPI_FREQUENCY  27000000 // Marauder // Actually sets it to 26.67MHz = 80/3
+// #define SPI_FREQUENCY  40000000
+// #define SPI_FREQUENCY  80000000
+
+// Optional reduced SPI frequency for reading TFT
+#define SPI_READ_FREQUENCY  20000000
+
+// The XPT2046 requires a lower SPI clock rate of 2.5MHz so we define that here:
+#define SPI_TOUCH_FREQUENCY  2500000
+
+// The ESP32 has 2 free SPI ports i.e. VSPI and HSPI, the VSPI is the default.
+// If the VSPI port is in use and pins are not accessible (e.g. TTGO T-Beam)
+// then uncomment the following line:
+#define USE_HSPI_PORT
+
+// Comment out the following #define if "SPI Transactions" do not need to be
+// supported. When commented out the code size will be smaller and sketches will
+// run slightly faster, so leave it commented out unless you need it!
+
+// Transaction support is needed to work with SD library but not needed with TFT_SdFat
+// Transaction support is required if other SPI devices are connected.
+
+// Transactions are automatically enabled by the library for an ESP32 (to use HAL mutex)
+// so changing it here has no effect
+
+// #define SUPPORT_TRANSACTIONS
--- a/User_Setup_cyd_guition.h
+++ b/User_Setup_cyd_guition.h
@@ -0,0 +1,316 @@
+//                            USER DEFINED SETTINGS
+//   Set driver type, fonts to be loaded, pins used and SPI control method etc
+//
+//   See the User_Setup_Select.h file if you wish to be able to define multiple
+//   setups and then easily select which setup file is used by the compiler.
+//
+//   If this file is edited correctly then all the library example sketches should
+//   run without the need to make any more changes for a particular hardware setup!
+//   Note that some sketches are designed for a particular TFT pixel width/height
+
+
+// ##################################################################################
+//
+// Section 1. Call up the right driver file and any options for it
+//
+// ##################################################################################
+
+// Display type -  only define if RPi display
+//#define RPI_DRIVER
+
+// Only define one driver, the other ones must be commented out
+#define ILI9341_DRIVER // OG Marauder
+//#define ST7735_DRIVER    // Marauder Mini  // Define additional parameters below for this display
+//#define ILI9163_DRIVER     // Define additional parameters below for this display
+//#define S6D02A1_DRIVER
+//#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
+//#define HX8357D_DRIVER
+//#define ILI9481_DRIVER
+//#define ILI9486_DRIVER
+//#define ILI9488_DRIVER     // WARNING: Do not connect ILI9488 display SDO to MISO if other devices share the SPI bus (TFT SDO does NOT tristate when CS is high)
+//#define ST7789_DRIVER      // Full configuration option, define additional parameters below for this display
+//#define ST7789_2_DRIVER    // Minimal configuration option, define additional parameters below for this display
+//#define R61581_DRIVER
+//#define RM68140_DRIVER
+//#define ST7796_DRIVER
+
+// Some displays support SPI reads via the MISO pin, other displays have a single
+// bi-directional SDA pin and the library will try to read this via the MOSI line.
+// To use the SDA line for reading data from the TFT uncomment the following line:
+
+// #define TFT_SDA_READ      // This option is for ESP32 ONLY, tested with ST7789 display only
+
+// For ST7789 and ILI9341 ONLY, define the colour order IF the blue and red are swapped on your display
+// Try ONE option at a time to find the correct colour order for your display
+
+//  #define TFT_RGB_ORDER TFT_RGB  // Colour order Red-Green-Blue
+//  #define TFT_RGB_ORDER TFT_BGR  // Colour order Blue-Green-Red
+
+// For M5Stack ESP32 module with integrated ILI9341 display ONLY, remove // in line below
+
+// #define M5STACK
+
+// For ST7789, ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation
+// #define TFT_WIDTH  80
+// #define TFT_WIDTH  128 // Marauder Mini
+ #define TFT_WIDTH  240 // ST7789 240 x 240 and 240 x 320
+// #define TFT_HEIGHT 160
+// #define TFT_HEIGHT 128 // Marauder Mini
+// #define TFT_HEIGHT 240 // ST7789 240 x 240
+ #define TFT_HEIGHT 320 // ST7789 240 x 320
+
+// For ST7735 ONLY, define the type of display, originally this was based on the
+// colour of the tab on the screen protector film but this is not always true, so try
+// out the different options below if the screen does not display graphics correctly,
+// e.g. colours wrong, mirror images, or tray pixels at the edges.
+// Comment out ALL BUT ONE of these options for a ST7735 display driver, save this
+// this User_Setup file, then rebuild and upload the sketch to the board again:
+
+// #define ST7735_INITB
+// #define ST7735_GREENTAB
+// #define ST7735_GREENTAB2
+// #define ST7735_GREENTAB3
+// #define ST7735_GREENTAB128    // For 128 x 128 display
+// #define ST7735_GREENTAB160x80 // For 160 x 80 display (BGR, inverted, 26 offset)
+// #define ST7735_REDTAB
+// #define ST7735_BLACKTAB
+// #define ST7735_REDTAB160x80   // For 160 x 80 display with 24 pixel offset
+
+// If colours are inverted (white shows as black) then uncomment one of the next
+// 2 lines try both options, one of the options should correct the inversion.
+
+// #define TFT_INVERSION_ON
+// #define TFT_INVERSION_OFF
+
+// If a backlight control signal is available then define the TFT_BL pin in Section 2
+// below. The backlight will be turned ON when tft.begin() is called, but the library
+// needs to know if the LEDs are ON with the pin HIGH or LOW. If the LEDs are to be
+// driven with a PWM signal or turned OFF/ON then this must be handled by the user
+// sketch. e.g. with digitalWrite(TFT_BL, LOW);
+
+// #define TFT_BACKLIGHT_ON LOW  // HIGH or LOW are options
+
+// ##################################################################################
+//
+// Section 2. Define the pins that are used to interface with the display here
+//
+// ##################################################################################
+
+// We must use hardware SPI, a minimum of 3 GPIO pins is needed.
+// Typical setup for ESP8266 NodeMCU ESP-12 is :
+//
+// Display SDO/MISO  to NodeMCU pin D6 (or leave disconnected if not reading TFT)
+// Display LED       to NodeMCU pin VIN (or 5V, see below)
+// Display SCK       to NodeMCU pin D5
+// Display SDI/MOSI  to NodeMCU pin D7
+// Display DC (RS/AO)to NodeMCU pin D3
+// Display RESET     to NodeMCU pin D4 (or RST, see below)
+// Display CS        to NodeMCU pin D8 (or GND, see below)
+// Display GND       to NodeMCU pin GND (0V)
+// Display VCC       to NodeMCU 5V or 3.3V
+//
+// The TFT RESET pin can be connected to the NodeMCU RST pin or 3.3V to free up a control pin
+//
+// The DC (Data Command) pin may be labeled AO or RS (Register Select)
+//
+// With some displays such as the ILI9341 the TFT CS pin can be connected to GND if no more
+// SPI devices (e.g. an SD Card) are connected, in this case comment out the #define TFT_CS
+// line below so it is NOT defined. Other displays such at the ST7735 require the TFT CS pin
+// to be toggled during setup, so in these cases the TFT_CS line must be defined and connected.
+//
+// The NodeMCU D0 pin can be used for RST
+//
+//
+// Note: only some versions of the NodeMCU provide the USB 5V on the VIN pin
+// If 5V is not available at a pin you can use 3.3V but backlight brightness
+// will be lower.
+
+
+// ###### EDIT THE PIN NUMBERS IN THE LINES FOLLOWING TO SUIT YOUR ESP8266 SETUP ######
+
+// For NodeMCU - use pin numbers in the form PIN_Dx where Dx is the NodeMCU pin designation
+//#define TFT_CS   PIN_D8  // Chip select control pin D8
+//#define TFT_DC   PIN_D3  // Data Command control pin
+//#define TFT_RST  PIN_D4  // Reset pin (could connect to NodeMCU RST, see next line)
+//#define TFT_RST  -1    // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
+
+//#define TFT_BL PIN_D1  // LED back-light (only for ST7789 with backlight control pin)
+
+//#define TOUCH_CS PIN_D2     // Chip select pin (T_CS) of touch screen
+
+//#define TFT_WR PIN_D2       // Write strobe for modified Raspberry Pi TFT only
+
+
+// ######  FOR ESP8266 OVERLAP MODE EDIT THE PIN NUMBERS IN THE FOLLOWING LINES  ######
+
+// Overlap mode shares the ESP8266 FLASH SPI bus with the TFT so has a performance impact
+// but saves pins for other functions. It is best not to connect MISO as some displays
+// do not tristate that line wjen chip select is high!
+// On NodeMCU 1.0 SD0=MISO, SD1=MOSI, CLK=SCLK to connect to TFT in overlap mode
+// On NodeMCU V3  S0 =MISO, S1 =MOSI, S2 =SCLK
+// In ESP8266 overlap mode the following must be defined
+
+//#define TFT_SPI_OVERLAP
+
+// In ESP8266 overlap mode the TFT chip select MUST connect to pin D3
+//#define TFT_CS   PIN_D3
+//#define TFT_DC   PIN_D5  // Data Command control pin
+//#define TFT_RST  PIN_D4  // Reset pin (could connect to NodeMCU RST, see next line)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
+
+
+// ###### EDIT THE PIN NUMBERS IN THE LINES FOLLOWING TO SUIT YOUR ESP32 SETUP   ######
+
+// For ESP32 Dev board (only tested with ILI9341 display)
+// The hardware SPI can be mapped to any pins
+
+// Marauder Mini
+/*
+#define TFT_CS   17  // Chip select control pin D8
+#define TFT_DC   16  // Data Command control pin
+#define TFT_RST  5  // Reset pin (could connect to NodeMCU RST, see next line)
+//#define TFT_MISO 19
+//#define TFT_MOSI 23
+//#define TFT_SCLK 18
+//#define TFT_BL   32
+*/
+
+// ESP32 Marauder 
+#define TFT_MISO 12
+#define TFT_MOSI 13
+#define TFT_SCLK 14
+#define TFT_CS   15  // Chip select control pin
+#define TFT_DC   2  // Data Command control pin
+#define TFT_RST   -1  // Reset pin (could connect to RST pin)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if display RESET is connected to ESP32 board RST
+
+#define TFT_BL   27  // LED back-light (only for ST7789 with backlight control pin)
+
+#define TOUCH_CS   33     // Chip select pin (T_CS) of touch screen
+
+/////////////////////////////
+
+// ESP32 Centauri
+/*
+#define TFT_MISO 19
+#define TFT_MOSI 23
+#define TFT_SCLK 18
+#define TFT_CS   27  // Chip select control pin
+#define TFT_DC   26  // Data Command control pin
+#define TFT_RST   5  // Reset pin (could connect to RST pin)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if display RESET is connected to ESP32 board RST
+
+#define TFT_BL   32  // LED back-light (only for ST7789 with backlight control pin)
+
+#define TOUCH_CS 21     // Chip select pin (T_CS) of touch screen
+*/
+/////////////////////////////
+
+//#define TFT_WR 22    // Write strobe for modified Raspberry Pi TFT only
+
+// For the M5Stack module use these #define lines
+//#define TFT_MISO 19
+//#define TFT_MOSI 23
+//#define TFT_SCLK 18
+//#define TFT_CS   14  // Chip select control pin
+//#define TFT_DC   27  // Data Command control pin
+//#define TFT_RST  33  // Reset pin (could connect to Arduino RESET pin)
+//#define TFT_BL   32  // LED back-light (required for M5Stack)
+
+// ######       EDIT THE PINs BELOW TO SUIT YOUR ESP32 PARALLEL TFT SETUP        ######
+
+// The library supports 8 bit parallel TFTs with the ESP32, the pin
+// selection below is compatible with ESP32 boards in UNO format.
+// Wemos D32 boards need to be modified, see diagram in Tools folder.
+// Only ILI9481 and ILI9341 based displays have been tested!
+
+// Parallel bus is only supported on ESP32
+// Uncomment line below to use ESP32 Parallel interface instead of SPI
+
+//#define ESP32_PARALLEL
+
+// The ESP32 and TFT the pins used for testing are:
+//#define TFT_CS   33  // Chip select control pin (library pulls permanently low
+//#define TFT_DC   15  // Data Command control pin - must use a pin in the range 0-31
+//#define TFT_RST  32  // Reset pin, toggles on startup
+
+//#define TFT_WR    4  // Write strobe control pin - must use a pin in the range 0-31
+//#define TFT_RD    2  // Read strobe control pin
+
+//#define TFT_D0   12  // Must use pins in the range 0-31 for the data bus
+//#define TFT_D1   13  // so a single register write sets/clears all bits.
+//#define TFT_D2   26  // Pins can be randomly assigned, this does not affect
+//#define TFT_D3   25  // TFT screen update performance.
+//#define TFT_D4   17
+//#define TFT_D5   16
+//#define TFT_D6   27
+//#define TFT_D7   14
+
+
+// ##################################################################################
+//
+// Section 3. Define the fonts that are to be used here
+//
+// ##################################################################################
+
+// Comment out the #defines below with // to stop that font being loaded
+// The ESP8366 and ESP32 have plenty of memory so commenting out fonts is not
+// normally necessary. If all fonts are loaded the extra FLASH space required is
+// about 17Kbytes. To save FLASH space only enable the fonts you need!
+
+#define LOAD_GLCD   // Font 1. Original Adafruit 8 pixel font needs ~1820 bytes in FLASH
+#define LOAD_FONT2  // Font 2. Small 16 pixel high font, needs ~3534 bytes in FLASH, 96 characters
+#define LOAD_FONT4  // Font 4. Medium 26 pixel high font, needs ~5848 bytes in FLASH, 96 characters
+#define LOAD_FONT6  // Font 6. Large 48 pixel font, needs ~2666 bytes in FLASH, only characters 1234567890:-.apm
+#define LOAD_FONT7  // Font 7. 7 segment 48 pixel font, needs ~2438 bytes in FLASH, only characters 1234567890:-.
+#define LOAD_FONT8  // Font 8. Large 75 pixel font needs ~3256 bytes in FLASH, only characters 1234567890:-.
+//#define LOAD_FONT8N // Font 8. Alternative to Font 8 above, slightly narrower, so 3 digits fit a 160 pixel TFT
+#define LOAD_GFXFF  // FreeFonts. Include access to the 48 Adafruit_GFX free fonts FF1 to FF48 and custom fonts
+
+// Comment out the #define below to stop the SPIFFS filing system and smooth font code being loaded
+// this will save ~20kbytes of FLASH
+#define SMOOTH_FONT
+
+
+// ##################################################################################
+//
+// Section 4. Other options
+//
+// ##################################################################################
+
+// Define the SPI clock frequency, this affects the graphics rendering speed. Too
+// fast and the TFT driver will not keep up and display corruption appears.
+// With an ILI9341 display 40MHz works OK, 80MHz sometimes fails
+// With a ST7735 display more than 27MHz may not work (spurious pixels and lines)
+// With an ILI9163 display 27 MHz works OK.
+
+// #define SPI_FREQUENCY   1000000
+//#define SPI_FREQUENCY   5000000
+// #define SPI_FREQUENCY  10000000
+// #define SPI_FREQUENCY  20000000
+#define SPI_FREQUENCY  27000000 // Marauder // Actually sets it to 26.67MHz = 80/3
+// #define SPI_FREQUENCY  40000000
+// #define SPI_FREQUENCY  80000000
+
+// Optional reduced SPI frequency for reading TFT
+#define SPI_READ_FREQUENCY  20000000
+
+// The XPT2046 requires a lower SPI clock rate of 2.5MHz so we define that here:
+#define SPI_TOUCH_FREQUENCY  2500000
+
+// The ESP32 has 2 free SPI ports i.e. VSPI and HSPI, the VSPI is the default.
+// If the VSPI port is in use and pins are not accessible (e.g. TTGO T-Beam)
+// then uncomment the following line:
+#define USE_HSPI_PORT
+
+// Comment out the following #define if "SPI Transactions" do not need to be
+// supported. When commented out the code size will be smaller and sketches will
+// run slightly faster, so leave it commented out unless you need it!
+
+// Transaction support is needed to work with SD library but not needed with TFT_SdFat
+// Transaction support is required if other SPI devices are connected.
+
+// Transactions are automatically enabled by the library for an ESP32 (to use HAL mutex)
+// so changing it here has no effect
+
+// #define SUPPORT_TRANSACTIONS
--- a/User_Setup_cyd_micro.h
+++ b/User_Setup_cyd_micro.h
@@ -0,0 +1,316 @@
+//                            USER DEFINED SETTINGS
+//   Set driver type, fonts to be loaded, pins used and SPI control method etc
+//
+//   See the User_Setup_Select.h file if you wish to be able to define multiple
+//   setups and then easily select which setup file is used by the compiler.
+//
+//   If this file is edited correctly then all the library example sketches should
+//   run without the need to make any more changes for a particular hardware setup!
+//   Note that some sketches are designed for a particular TFT pixel width/height
+
+
+// ##################################################################################
+//
+// Section 1. Call up the right driver file and any options for it
+//
+// ##################################################################################
+
+// Display type -  only define if RPi display
+//#define RPI_DRIVER
+
+// Only define one driver, the other ones must be commented out
+#define ILI9341_DRIVER // OG Marauder
+//#define ST7735_DRIVER    // Marauder Mini  // Define additional parameters below for this display
+//#define ILI9163_DRIVER     // Define additional parameters below for this display
+//#define S6D02A1_DRIVER
+//#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
+//#define HX8357D_DRIVER
+//#define ILI9481_DRIVER
+//#define ILI9486_DRIVER
+//#define ILI9488_DRIVER     // WARNING: Do not connect ILI9488 display SDO to MISO if other devices share the SPI bus (TFT SDO does NOT tristate when CS is high)
+//#define ST7789_DRIVER      // Full configuration option, define additional parameters below for this display
+//#define ST7789_2_DRIVER    // Minimal configuration option, define additional parameters below for this display
+//#define R61581_DRIVER
+//#define RM68140_DRIVER
+//#define ST7796_DRIVER
+
+// Some displays support SPI reads via the MISO pin, other displays have a single
+// bi-directional SDA pin and the library will try to read this via the MOSI line.
+// To use the SDA line for reading data from the TFT uncomment the following line:
+
+// #define TFT_SDA_READ      // This option is for ESP32 ONLY, tested with ST7789 display only
+
+// For ST7789 and ILI9341 ONLY, define the colour order IF the blue and red are swapped on your display
+// Try ONE option at a time to find the correct colour order for your display
+
+//  #define TFT_RGB_ORDER TFT_RGB  // Colour order Red-Green-Blue
+//  #define TFT_RGB_ORDER TFT_BGR  // Colour order Blue-Green-Red
+
+// For M5Stack ESP32 module with integrated ILI9341 display ONLY, remove // in line below
+
+// #define M5STACK
+
+// For ST7789, ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation
+// #define TFT_WIDTH  80
+// #define TFT_WIDTH  128 // Marauder Mini
+ #define TFT_WIDTH  240 // ST7789 240 x 240 and 240 x 320
+// #define TFT_HEIGHT 160
+// #define TFT_HEIGHT 128 // Marauder Mini
+// #define TFT_HEIGHT 240 // ST7789 240 x 240
+ #define TFT_HEIGHT 320 // ST7789 240 x 320
+
+// For ST7735 ONLY, define the type of display, originally this was based on the
+// colour of the tab on the screen protector film but this is not always true, so try
+// out the different options below if the screen does not display graphics correctly,
+// e.g. colours wrong, mirror images, or tray pixels at the edges.
+// Comment out ALL BUT ONE of these options for a ST7735 display driver, save this
+// this User_Setup file, then rebuild and upload the sketch to the board again:
+
+// #define ST7735_INITB
+// #define ST7735_GREENTAB
+// #define ST7735_GREENTAB2
+// #define ST7735_GREENTAB3
+// #define ST7735_GREENTAB128    // For 128 x 128 display
+// #define ST7735_GREENTAB160x80 // For 160 x 80 display (BGR, inverted, 26 offset)
+// #define ST7735_REDTAB
+// #define ST7735_BLACKTAB
+// #define ST7735_REDTAB160x80   // For 160 x 80 display with 24 pixel offset
+
+// If colours are inverted (white shows as black) then uncomment one of the next
+// 2 lines try both options, one of the options should correct the inversion.
+
+// #define TFT_INVERSION_ON
+// #define TFT_INVERSION_OFF
+
+// If a backlight control signal is available then define the TFT_BL pin in Section 2
+// below. The backlight will be turned ON when tft.begin() is called, but the library
+// needs to know if the LEDs are ON with the pin HIGH or LOW. If the LEDs are to be
+// driven with a PWM signal or turned OFF/ON then this must be handled by the user
+// sketch. e.g. with digitalWrite(TFT_BL, LOW);
+
+// #define TFT_BACKLIGHT_ON LOW  // HIGH or LOW are options
+
+// ##################################################################################
+//
+// Section 2. Define the pins that are used to interface with the display here
+//
+// ##################################################################################
+
+// We must use hardware SPI, a minimum of 3 GPIO pins is needed.
+// Typical setup for ESP8266 NodeMCU ESP-12 is :
+//
+// Display SDO/MISO  to NodeMCU pin D6 (or leave disconnected if not reading TFT)
+// Display LED       to NodeMCU pin VIN (or 5V, see below)
+// Display SCK       to NodeMCU pin D5
+// Display SDI/MOSI  to NodeMCU pin D7
+// Display DC (RS/AO)to NodeMCU pin D3
+// Display RESET     to NodeMCU pin D4 (or RST, see below)
+// Display CS        to NodeMCU pin D8 (or GND, see below)
+// Display GND       to NodeMCU pin GND (0V)
+// Display VCC       to NodeMCU 5V or 3.3V
+//
+// The TFT RESET pin can be connected to the NodeMCU RST pin or 3.3V to free up a control pin
+//
+// The DC (Data Command) pin may be labeled AO or RS (Register Select)
+//
+// With some displays such as the ILI9341 the TFT CS pin can be connected to GND if no more
+// SPI devices (e.g. an SD Card) are connected, in this case comment out the #define TFT_CS
+// line below so it is NOT defined. Other displays such at the ST7735 require the TFT CS pin
+// to be toggled during setup, so in these cases the TFT_CS line must be defined and connected.
+//
+// The NodeMCU D0 pin can be used for RST
+//
+//
+// Note: only some versions of the NodeMCU provide the USB 5V on the VIN pin
+// If 5V is not available at a pin you can use 3.3V but backlight brightness
+// will be lower.
+
+
+// ###### EDIT THE PIN NUMBERS IN THE LINES FOLLOWING TO SUIT YOUR ESP8266 SETUP ######
+
+// For NodeMCU - use pin numbers in the form PIN_Dx where Dx is the NodeMCU pin designation
+//#define TFT_CS   PIN_D8  // Chip select control pin D8
+//#define TFT_DC   PIN_D3  // Data Command control pin
+//#define TFT_RST  PIN_D4  // Reset pin (could connect to NodeMCU RST, see next line)
+//#define TFT_RST  -1    // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
+
+//#define TFT_BL PIN_D1  // LED back-light (only for ST7789 with backlight control pin)
+
+//#define TOUCH_CS PIN_D2     // Chip select pin (T_CS) of touch screen
+
+//#define TFT_WR PIN_D2       // Write strobe for modified Raspberry Pi TFT only
+
+
+// ######  FOR ESP8266 OVERLAP MODE EDIT THE PIN NUMBERS IN THE FOLLOWING LINES  ######
+
+// Overlap mode shares the ESP8266 FLASH SPI bus with the TFT so has a performance impact
+// but saves pins for other functions. It is best not to connect MISO as some displays
+// do not tristate that line wjen chip select is high!
+// On NodeMCU 1.0 SD0=MISO, SD1=MOSI, CLK=SCLK to connect to TFT in overlap mode
+// On NodeMCU V3  S0 =MISO, S1 =MOSI, S2 =SCLK
+// In ESP8266 overlap mode the following must be defined
+
+//#define TFT_SPI_OVERLAP
+
+// In ESP8266 overlap mode the TFT chip select MUST connect to pin D3
+//#define TFT_CS   PIN_D3
+//#define TFT_DC   PIN_D5  // Data Command control pin
+//#define TFT_RST  PIN_D4  // Reset pin (could connect to NodeMCU RST, see next line)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
+
+
+// ###### EDIT THE PIN NUMBERS IN THE LINES FOLLOWING TO SUIT YOUR ESP32 SETUP   ######
+
+// For ESP32 Dev board (only tested with ILI9341 display)
+// The hardware SPI can be mapped to any pins
+
+// Marauder Mini
+/*
+#define TFT_CS   17  // Chip select control pin D8
+#define TFT_DC   16  // Data Command control pin
+#define TFT_RST  5  // Reset pin (could connect to NodeMCU RST, see next line)
+//#define TFT_MISO 19
+//#define TFT_MOSI 23
+//#define TFT_SCLK 18
+//#define TFT_BL   32
+*/
+
+// ESP32 Marauder 
+#define TFT_MISO 12
+#define TFT_MOSI 13
+#define TFT_SCLK 14
+#define TFT_CS   15  // Chip select control pin
+#define TFT_DC   2  // Data Command control pin
+#define TFT_RST   -1  // Reset pin (could connect to RST pin)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if display RESET is connected to ESP32 board RST
+
+#define TFT_BL   21  // LED back-light (only for ST7789 with backlight control pin)
+
+#define TOUCH_CS   33     // Chip select pin (T_CS) of touch screen
+
+/////////////////////////////
+
+// ESP32 Centauri
+/*
+#define TFT_MISO 19
+#define TFT_MOSI 23
+#define TFT_SCLK 18
+#define TFT_CS   27  // Chip select control pin
+#define TFT_DC   26  // Data Command control pin
+#define TFT_RST   5  // Reset pin (could connect to RST pin)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if display RESET is connected to ESP32 board RST
+
+#define TFT_BL   32  // LED back-light (only for ST7789 with backlight control pin)
+
+#define TOUCH_CS 21     // Chip select pin (T_CS) of touch screen
+*/
+/////////////////////////////
+
+//#define TFT_WR 22    // Write strobe for modified Raspberry Pi TFT only
+
+// For the M5Stack module use these #define lines
+//#define TFT_MISO 19
+//#define TFT_MOSI 23
+//#define TFT_SCLK 18
+//#define TFT_CS   14  // Chip select control pin
+//#define TFT_DC   27  // Data Command control pin
+//#define TFT_RST  33  // Reset pin (could connect to Arduino RESET pin)
+//#define TFT_BL   32  // LED back-light (required for M5Stack)
+
+// ######       EDIT THE PINs BELOW TO SUIT YOUR ESP32 PARALLEL TFT SETUP        ######
+
+// The library supports 8 bit parallel TFTs with the ESP32, the pin
+// selection below is compatible with ESP32 boards in UNO format.
+// Wemos D32 boards need to be modified, see diagram in Tools folder.
+// Only ILI9481 and ILI9341 based displays have been tested!
+
+// Parallel bus is only supported on ESP32
+// Uncomment line below to use ESP32 Parallel interface instead of SPI
+
+//#define ESP32_PARALLEL
+
+// The ESP32 and TFT the pins used for testing are:
+//#define TFT_CS   33  // Chip select control pin (library pulls permanently low
+//#define TFT_DC   15  // Data Command control pin - must use a pin in the range 0-31
+//#define TFT_RST  32  // Reset pin, toggles on startup
+
+//#define TFT_WR    4  // Write strobe control pin - must use a pin in the range 0-31
+//#define TFT_RD    2  // Read strobe control pin
+
+//#define TFT_D0   12  // Must use pins in the range 0-31 for the data bus
+//#define TFT_D1   13  // so a single register write sets/clears all bits.
+//#define TFT_D2   26  // Pins can be randomly assigned, this does not affect
+//#define TFT_D3   25  // TFT screen update performance.
+//#define TFT_D4   17
+//#define TFT_D5   16
+//#define TFT_D6   27
+//#define TFT_D7   14
+
+
+// ##################################################################################
+//
+// Section 3. Define the fonts that are to be used here
+//
+// ##################################################################################
+
+// Comment out the #defines below with // to stop that font being loaded
+// The ESP8366 and ESP32 have plenty of memory so commenting out fonts is not
+// normally necessary. If all fonts are loaded the extra FLASH space required is
+// about 17Kbytes. To save FLASH space only enable the fonts you need!
+
+#define LOAD_GLCD   // Font 1. Original Adafruit 8 pixel font needs ~1820 bytes in FLASH
+#define LOAD_FONT2  // Font 2. Small 16 pixel high font, needs ~3534 bytes in FLASH, 96 characters
+#define LOAD_FONT4  // Font 4. Medium 26 pixel high font, needs ~5848 bytes in FLASH, 96 characters
+#define LOAD_FONT6  // Font 6. Large 48 pixel font, needs ~2666 bytes in FLASH, only characters 1234567890:-.apm
+#define LOAD_FONT7  // Font 7. 7 segment 48 pixel font, needs ~2438 bytes in FLASH, only characters 1234567890:-.
+#define LOAD_FONT8  // Font 8. Large 75 pixel font needs ~3256 bytes in FLASH, only characters 1234567890:-.
+//#define LOAD_FONT8N // Font 8. Alternative to Font 8 above, slightly narrower, so 3 digits fit a 160 pixel TFT
+#define LOAD_GFXFF  // FreeFonts. Include access to the 48 Adafruit_GFX free fonts FF1 to FF48 and custom fonts
+
+// Comment out the #define below to stop the SPIFFS filing system and smooth font code being loaded
+// this will save ~20kbytes of FLASH
+#define SMOOTH_FONT
+
+
+// ##################################################################################
+//
+// Section 4. Other options
+//
+// ##################################################################################
+
+// Define the SPI clock frequency, this affects the graphics rendering speed. Too
+// fast and the TFT driver will not keep up and display corruption appears.
+// With an ILI9341 display 40MHz works OK, 80MHz sometimes fails
+// With a ST7735 display more than 27MHz may not work (spurious pixels and lines)
+// With an ILI9163 display 27 MHz works OK.
+
+// #define SPI_FREQUENCY   1000000
+//#define SPI_FREQUENCY   5000000
+// #define SPI_FREQUENCY  10000000
+// #define SPI_FREQUENCY  20000000
+#define SPI_FREQUENCY  27000000 // Marauder // Actually sets it to 26.67MHz = 80/3
+// #define SPI_FREQUENCY  40000000
+// #define SPI_FREQUENCY  80000000
+
+// Optional reduced SPI frequency for reading TFT
+#define SPI_READ_FREQUENCY  20000000
+
+// The XPT2046 requires a lower SPI clock rate of 2.5MHz so we define that here:
+#define SPI_TOUCH_FREQUENCY  2500000
+
+// The ESP32 has 2 free SPI ports i.e. VSPI and HSPI, the VSPI is the default.
+// If the VSPI port is in use and pins are not accessible (e.g. TTGO T-Beam)
+// then uncomment the following line:
+#define USE_HSPI_PORT
+
+// Comment out the following #define if "SPI Transactions" do not need to be
+// supported. When commented out the code size will be smaller and sketches will
+// run slightly faster, so leave it commented out unless you need it!
+
+// Transaction support is needed to work with SD library but not needed with TFT_SdFat
+// Transaction support is required if other SPI devices are connected.
+
+// Transactions are automatically enabled by the library for an ESP32 (to use HAL mutex)
+// so changing it here has no effect
+
+// #define SUPPORT_TRANSACTIONS
--- a/User_Setup_marauder_m5cardputer.h
+++ b/User_Setup_marauder_m5cardputer.h
@@ -0,0 +1,328 @@
+//                            USER DEFINED SETTINGS
+//   Set driver type, fonts to be loaded, pins used and SPI control method etc
+//
+//   See the User_Setup_Select.h file if you wish to be able to define multiple
+//   setups and then easily select which setup file is used by the compiler.
+//
+//   If this file is edited correctly then all the library example sketches should
+//   run without the need to make any more changes for a particular hardware setup!
+//   Note that some sketches are designed for a particular TFT pixel width/height
+
+
+// ##################################################################################
+//
+// Section 1. Call up the right driver file and any options for it
+//
+// ##################################################################################
+
+// Display type -  only define if RPi display
+//#define RPI_DRIVER
+
+#define CGRAM_OFFSET
+
+// Only define one driver, the other ones must be commented out
+//#define ILI9341_DRIVER // OG Marauder
+//#define ST7735_DRIVER    // Marauder Mini  // Define additional parameters below for this display
+//#define ILI9163_DRIVER     // Define additional parameters below for this display
+//#define S6D02A1_DRIVER
+//#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
+//#define HX8357D_DRIVER
+//#define ILI9481_DRIVER
+//#define ILI9486_DRIVER
+//#define ILI9488_DRIVER     // WARNING: Do not connect ILI9488 display SDO to MISO if other devices share the SPI bus (TFT SDO does NOT tristate when CS is high)
+//#define ST7789_DRIVER      // Full configuration option, define additional parameters below for this display
+#define ST7789_2_DRIVER    // Minimal configuration option, define additional parameters below for this display
+//#define R61581_DRIVER
+//#define RM68140_DRIVER
+//#define ST7796_DRIVER
+
+// Some displays support SPI reads via the MISO pin, other displays have a single
+// bi-directional SDA pin and the library will try to read this via the MOSI line.
+// To use the SDA line for reading data from the TFT uncomment the following line:
+
+// #define TFT_SDA_READ      // This option is for ESP32 ONLY, tested with ST7789 display only
+
+// For ST7789 and ILI9341 ONLY, define the colour order IF the blue and red are swapped on your display
+// Try ONE option at a time to find the correct colour order for your display
+
+  #define TFT_RGB_ORDER TFT_RGB  // Colour order Red-Green-Blue
+//  #define TFT_RGB_ORDER TFT_BGR  // Colour order Blue-Green-Red
+
+// For M5Stack ESP32 module with integrated ILI9341 display ONLY, remove // in line below
+
+// #define M5STACK
+
+// For ST7789, ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation
+// #define TFT_WIDTH  80
+ #define TFT_WIDTH  135 // Marauder Mini
+// #define TFT_WIDTH  240 // ST7789 240 x 240 and 240 x 320
+// #define TFT_HEIGHT 160
+ #define TFT_HEIGHT 240 // Marauder Mini
+// #define TFT_HEIGHT 240 // ST7789 240 x 240
+// #define TFT_HEIGHT 320 // ST7789 240 x 320
+
+// For ST7735 ONLY, define the type of display, originally this was based on the
+// colour of the tab on the screen protector film but this is not always true, so try
+// out the different options below if the screen does not display graphics correctly,
+// e.g. colours wrong, mirror images, or tray pixels at the edges.
+// Comment out ALL BUT ONE of these options for a ST7735 display driver, save this
+// this User_Setup file, then rebuild and upload the sketch to the board again:
+
+// #define ST7735_INITB
+// #define ST7735_GREENTAB
+// #define ST7735_GREENTAB2
+// #define ST7735_GREENTAB3
+// #define ST7735_GREENTAB128    // For 128 x 128 display
+// #define ST7735_GREENTAB160x80 // For 160 x 80 display (BGR, inverted, 26 offset)
+// #define ST7735_REDTAB
+// #define ST7735_BLACKTAB
+// #define ST7735_REDTAB160x80   // For 160 x 80 display with 24 pixel offset
+
+// If colours are inverted (white shows as black) then uncomment one of the next
+// 2 lines try both options, one of the options should correct the inversion.
+
+// #define TFT_INVERSION_ON
+// #define TFT_INVERSION_OFF
+
+// If a backlight control signal is available then define the TFT_BL pin in Section 2
+// below. The backlight will be turned ON when tft.begin() is called, but the library
+// needs to know if the LEDs are ON with the pin HIGH or LOW. If the LEDs are to be
+// driven with a PWM signal or turned OFF/ON then this must be handled by the user
+// sketch. e.g. with digitalWrite(TFT_BL, LOW);
+
+ #define TFT_BACKLIGHT_ON HIGH  // HIGH or LOW are options
+
+// ##################################################################################
+//
+// Section 2. Define the pins that are used to interface with the display here
+//
+// ##################################################################################
+
+// We must use hardware SPI, a minimum of 3 GPIO pins is needed.
+// Typical setup for ESP8266 NodeMCU ESP-12 is :
+//
+// Display SDO/MISO  to NodeMCU pin D6 (or leave disconnected if not reading TFT)
+// Display LED       to NodeMCU pin VIN (or 5V, see below)
+// Display SCK       to NodeMCU pin D5
+// Display SDI/MOSI  to NodeMCU pin D7
+// Display DC (RS/AO)to NodeMCU pin D3
+// Display RESET     to NodeMCU pin D4 (or RST, see below)
+// Display CS        to NodeMCU pin D8 (or GND, see below)
+// Display GND       to NodeMCU pin GND (0V)
+// Display VCC       to NodeMCU 5V or 3.3V
+//
+// The TFT RESET pin can be connected to the NodeMCU RST pin or 3.3V to free up a control pin
+//
+// The DC (Data Command) pin may be labeled AO or RS (Register Select)
+//
+// With some displays such as the ILI9341 the TFT CS pin can be connected to GND if no more
+// SPI devices (e.g. an SD Card) are connected, in this case comment out the #define TFT_CS
+// line below so it is NOT defined. Other displays such at the ST7735 require the TFT CS pin
+// to be toggled during setup, so in these cases the TFT_CS line must be defined and connected.
+//
+// The NodeMCU D0 pin can be used for RST
+//
+//
+// Note: only some versions of the NodeMCU provide the USB 5V on the VIN pin
+// If 5V is not available at a pin you can use 3.3V but backlight brightness
+// will be lower.
+
+
+// ###### EDIT THE PIN NUMBERS IN THE LINES FOLLOWING TO SUIT YOUR ESP8266 SETUP ######
+
+// For NodeMCU - use pin numbers in the form PIN_Dx where Dx is the NodeMCU pin designation
+//#define TFT_CS   PIN_D8  // Chip select control pin D8
+//#define TFT_DC   PIN_D3  // Data Command control pin
+//#define TFT_RST  PIN_D4  // Reset pin (could connect to NodeMCU RST, see next line)
+//#define TFT_RST  -1    // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
+
+//#define TFT_BL PIN_D1  // LED back-light (only for ST7789 with backlight control pin)
+
+//#define TOUCH_CS PIN_D2     // Chip select pin (T_CS) of touch screen
+
+//#define TFT_WR PIN_D2       // Write strobe for modified Raspberry Pi TFT only
+
+
+// ######  FOR ESP8266 OVERLAP MODE EDIT THE PIN NUMBERS IN THE FOLLOWING LINES  ######
+
+// Overlap mode shares the ESP8266 FLASH SPI bus with the TFT so has a performance impact
+// but saves pins for other functions. It is best not to connect MISO as some displays
+// do not tristate that line wjen chip select is high!
+// On NodeMCU 1.0 SD0=MISO, SD1=MOSI, CLK=SCLK to connect to TFT in overlap mode
+// On NodeMCU V3  S0 =MISO, S1 =MOSI, S2 =SCLK
+// In ESP8266 overlap mode the following must be defined
+
+//#define TFT_SPI_OVERLAP
+
+// In ESP8266 overlap mode the TFT chip select MUST connect to pin D3
+//#define TFT_CS   PIN_D3
+//#define TFT_DC   PIN_D5  // Data Command control pin
+//#define TFT_RST  PIN_D4  // Reset pin (could connect to NodeMCU RST, see next line)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
+
+
+// ###### EDIT THE PIN NUMBERS IN THE LINES FOLLOWING TO SUIT YOUR ESP32 SETUP   ######
+
+// For ESP32 Dev board (only tested with ILI9341 display)
+// The hardware SPI can be mapped to any pins
+
+// M5 Cardputer
+#define TFT_BL   38
+#define TFT_RST  33  // Reset pin (could connect to NodeMCU RST, see next line)
+#define TFT_DC   34  // Data Command control pin
+#define TFT_MOSI 35
+#define TFT_SCLK 36
+#define TFT_CS   37  // Chip select control pin D8
+#define TOUCH_CS -1
+// #define TFT_MISO -1
+
+// Display SDO/MISO  to NodeMCU pin D6 (or leave disconnected if not reading TFT)
+// Display LED       to NodeMCU pin VIN (or 5V, see below)
+// Display SCK       to NodeMCU pin D5
+// Display SDI/MOSI  to NodeMCU pin D7
+// Display DC (RS/AO)to NodeMCU pin D3
+// Display RESET     to NodeMCU pin D4 (or RST, see below)
+// Display CS        to NodeMCU pin D8 (or GND, see below)
+// Display GND       to NodeMCU pin GND (0V)
+// Display VCC       to NodeMCU 5V or 3.3V
+
+/*
+// ESP32 Marauder 
+#define TFT_MISO 19
+#define TFT_MOSI 23
+#define TFT_SCLK 18
+#define TFT_CS   17  // Chip select control pin
+#define TFT_DC   16  // Data Command control pin
+#define TFT_RST   5  // Reset pin (could connect to RST pin)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if display RESET is connected to ESP32 board RST
+
+#define TFT_BL   32  // LED back-light (only for ST7789 with backlight control pin)
+
+#define TOUCH_CS 21     // Chip select pin (T_CS) of touch screen
+*/
+/////////////////////////////
+
+// ESP32 Centauri
+/*
+#define TFT_MISO 19
+#define TFT_MOSI 23
+#define TFT_SCLK 18
+#define TFT_CS   27  // Chip select control pin
+#define TFT_DC   26  // Data Command control pin
+#define TFT_RST   5  // Reset pin (could connect to RST pin)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if display RESET is connected to ESP32 board RST
+
+#define TFT_BL   32  // LED back-light (only for ST7789 with backlight control pin)
+
+#define TOUCH_CS 21     // Chip select pin (T_CS) of touch screen
+*/
+/////////////////////////////
+
+//#define TFT_WR 22    // Write strobe for modified Raspberry Pi TFT only
+
+// For the M5Stack module use these #define lines
+//#define TFT_MISO 19
+//#define TFT_MOSI 23
+//#define TFT_SCLK 18
+//#define TFT_CS   14  // Chip select control pin
+//#define TFT_DC   27  // Data Command control pin
+//#define TFT_RST  33  // Reset pin (could connect to Arduino RESET pin)
+//#define TFT_BL   32  // LED back-light (required for M5Stack)
+
+// ######       EDIT THE PINs BELOW TO SUIT YOUR ESP32 PARALLEL TFT SETUP        ######
+
+// The library supports 8 bit parallel TFTs with the ESP32, the pin
+// selection below is compatible with ESP32 boards in UNO format.
+// Wemos D32 boards need to be modified, see diagram in Tools folder.
+// Only ILI9481 and ILI9341 based displays have been tested!
+
+// Parallel bus is only supported on ESP32
+// Uncomment line below to use ESP32 Parallel interface instead of SPI
+
+//#define ESP32_PARALLEL
+
+// The ESP32 and TFT the pins used for testing are:
+//#define TFT_CS   33  // Chip select control pin (library pulls permanently low
+//#define TFT_DC   15  // Data Command control pin - must use a pin in the range 0-31
+//#define TFT_RST  32  // Reset pin, toggles on startup
+
+//#define TFT_WR    4  // Write strobe control pin - must use a pin in the range 0-31
+//#define TFT_RD    2  // Read strobe control pin
+
+//#define TFT_D0   12  // Must use pins in the range 0-31 for the data bus
+//#define TFT_D1   13  // so a single register write sets/clears all bits.
+//#define TFT_D2   26  // Pins can be randomly assigned, this does not affect
+//#define TFT_D3   25  // TFT screen update performance.
+//#define TFT_D4   17
+//#define TFT_D5   16
+//#define TFT_D6   27
+//#define TFT_D7   14
+
+
+// ##################################################################################
+//
+// Section 3. Define the fonts that are to be used here
+//
+// ##################################################################################
+
+// Comment out the #defines below with // to stop that font being loaded
+// The ESP8366 and ESP32 have plenty of memory so commenting out fonts is not
+// normally necessary. If all fonts are loaded the extra FLASH space required is
+// about 17Kbytes. To save FLASH space only enable the fonts you need!
+
+#define LOAD_GLCD   // Font 1. Original Adafruit 8 pixel font needs ~1820 bytes in FLASH
+#define LOAD_FONT2  // Font 2. Small 16 pixel high font, needs ~3534 bytes in FLASH, 96 characters
+#define LOAD_FONT4  // Font 4. Medium 26 pixel high font, needs ~5848 bytes in FLASH, 96 characters
+#define LOAD_FONT6  // Font 6. Large 48 pixel font, needs ~2666 bytes in FLASH, only characters 1234567890:-.apm
+#define LOAD_FONT7  // Font 7. 7 segment 48 pixel font, needs ~2438 bytes in FLASH, only characters 1234567890:-.
+#define LOAD_FONT8  // Font 8. Large 75 pixel font needs ~3256 bytes in FLASH, only characters 1234567890:-.
+//#define LOAD_FONT8N // Font 8. Alternative to Font 8 above, slightly narrower, so 3 digits fit a 160 pixel TFT
+#define LOAD_GFXFF  // FreeFonts. Include access to the 48 Adafruit_GFX free fonts FF1 to FF48 and custom fonts
+
+// Comment out the #define below to stop the SPIFFS filing system and smooth font code being loaded
+// this will save ~20kbytes of FLASH
+#define SMOOTH_FONT
+
+
+// ##################################################################################
+//
+// Section 4. Other options
+//
+// ##################################################################################
+
+// Define the SPI clock frequency, this affects the graphics rendering speed. Too
+// fast and the TFT driver will not keep up and display corruption appears.
+// With an ILI9341 display 40MHz works OK, 80MHz sometimes fails
+// With a ST7735 display more than 27MHz may not work (spurious pixels and lines)
+// With an ILI9163 display 27 MHz works OK.
+
+// #define SPI_FREQUENCY   1000000
+//#define SPI_FREQUENCY   5000000
+// #define SPI_FREQUENCY  10000000
+ #define SPI_FREQUENCY  20000000
+//#define SPI_FREQUENCY  27000000 // Marauder // Actually sets it to 26.67MHz = 80/3
+// #define SPI_FREQUENCY  40000000
+// #define SPI_FREQUENCY  80000000
+
+// Optional reduced SPI frequency for reading TFT
+#define SPI_READ_FREQUENCY  20000000
+
+// The XPT2046 requires a lower SPI clock rate of 2.5MHz so we define that here:
+#define SPI_TOUCH_FREQUENCY  2500000
+
+// The ESP32 has 2 free SPI ports i.e. VSPI and HSPI, the VSPI is the default.
+// If the VSPI port is in use and pins are not accessible (e.g. TTGO T-Beam)
+// then uncomment the following line:
+//#define USE_HSPI_PORT
+
+// Comment out the following #define if "SPI Transactions" do not need to be
+// supported. When commented out the code size will be smaller and sketches will
+// run slightly faster, so leave it commented out unless you need it!
+
+// Transaction support is needed to work with SD library but not needed with TFT_SdFat
+// Transaction support is required if other SPI devices are connected.
+
+// Transactions are automatically enabled by the library for an ESP32 (to use HAL mutex)
+// so changing it here has no effect
+
+// #define SUPPORT_TRANSACTIONS
--- a/User_Setup_pocket_sdr_3.h
+++ b/User_Setup_pocket_sdr_3.h
@@ -0,0 +1,330 @@
+//                            USER DEFINED SETTINGS
+//   Set driver type, fonts to be loaded, pins used and SPI control method etc
+//
+//   See the User_Setup_Select.h file if you wish to be able to define multiple
+//   setups and then easily select which setup file is used by the compiler.
+//
+//   If this file is edited correctly then all the library example sketches should
+//   run without the need to make any more changes for a particular hardware setup!
+//   Note that some sketches are designed for a particular TFT pixel width/height
+
+
+// ##################################################################################
+//
+// Section 1. Call up the right driver file and any options for it
+//
+// ##################################################################################
+
+// Display type -  only define if RPi display
+//#define RPI_DRIVER
+
+// Only define one driver, the other ones must be commented out
+//#define ILI9341_DRIVER // OG Marauder
+#define ST7735_DRIVER    // Marauder Mini  // Define additional parameters below for this display
+//#define ILI9163_DRIVER     // Define additional parameters below for this display
+//#define S6D02A1_DRIVER
+//#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
+//#define HX8357D_DRIVER
+//#define ILI9481_DRIVER
+//#define ILI9486_DRIVER
+//#define ILI9488_DRIVER     // WARNING: Do not connect ILI9488 display SDO to MISO if other devices share the SPI bus (TFT SDO does NOT tristate when CS is high)
+//#define ST7789_DRIVER      // Full configuration option, define additional parameters below for this display
+//#define ST7789_2_DRIVER    // Minimal configuration option, define additional parameters below for this display
+//#define R61581_DRIVER
+//#define RM68140_DRIVER
+//#define ST7796_DRIVER
+
+// Some displays support SPI reads via the MISO pin, other displays have a single
+// bi-directional SDA pin and the library will try to read this via the MOSI line.
+// To use the SDA line for reading data from the TFT uncomment the following line:
+
+// #define TFT_SDA_READ      // This option is for ESP32 ONLY, tested with ST7789 display only
+
+// For ST7789 and ILI9341 ONLY, define the colour order IF the blue and red are swapped on your display
+// Try ONE option at a time to find the correct colour order for your display
+
+//  #define TFT_RGB_ORDER TFT_RGB  // Colour order Red-Green-Blue
+  #define TFT_RGB_ORDER TFT_BGR  // Colour order Blue-Green-Red
+
+// For M5Stack ESP32 module with integrated ILI9341 display ONLY, remove // in line below
+
+// #define M5STACK
+
+// For ST7789, ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation
+ #define TFT_WIDTH  80
+// #define TFT_WIDTH  128 // Marauder Mini
+// #define TFT_WIDTH  240 // ST7789 240 x 240 and 240 x 320
+ #define TFT_HEIGHT 160
+// #define TFT_HEIGHT 128 // Marauder Mini
+// #define TFT_HEIGHT 240 // ST7789 240 x 240
+// #define TFT_HEIGHT 320 // ST7789 240 x 320
+
+// For ST7735 ONLY, define the type of display, originally this was based on the
+// colour of the tab on the screen protector film but this is not always true, so try
+// out the different options below if the screen does not display graphics correctly,
+// e.g. colours wrong, mirror images, or tray pixels at the edges.
+// Comment out ALL BUT ONE of these options for a ST7735 display driver, save this
+// this User_Setup file, then rebuild and upload the sketch to the board again:
+
+// #define ST7735_INITB
+// #define ST7735_GREENTAB
+// #define ST7735_GREENTAB2
+// #define ST7735_GREENTAB3
+// #define ST7735_GREENTAB128    // For 128 x 128 display
+// #define ST7735_GREENTAB160x80 // For 160 x 80 display (BGR, inverted, 26 offset)
+// #define ST7735_REDTAB
+// #define ST7735_BLACKTAB
+ #define ST7735_REDTAB160x80   // For 160 x 80 display with 24 pixel offset
+
+// If colours are inverted (white shows as black) then uncomment one of the next
+// 2 lines try both options, one of the options should correct the inversion.
+
+// #define TFT_INVERSION_ON
+ #define TFT_INVERSION_OFF
+
+// If a backlight control signal is available then define the TFT_BL pin in Section 2
+// below. The backlight will be turned ON when tft.begin() is called, but the library
+// needs to know if the LEDs are ON with the pin HIGH or LOW. If the LEDs are to be
+// driven with a PWM signal or turned OFF/ON then this must be handled by the user
+// sketch. e.g. with digitalWrite(TFT_BL, LOW);
+
+ #define TFT_BACKLIGHT_ON LOW  // HIGH or LOW are options
+
+// ##################################################################################
+//
+// Section 2. Define the pins that are used to interface with the display here
+//
+// ##################################################################################
+
+// We must use hardware SPI, a minimum of 3 GPIO pins is needed.
+// Typical setup for ESP8266 NodeMCU ESP-12 is :
+//
+// Display SDO/MISO  to NodeMCU pin D6 (or leave disconnected if not reading TFT)
+// Display LED       to NodeMCU pin VIN (or 5V, see below)
+// Display SCK       to NodeMCU pin D5
+// Display SDI/MOSI  to NodeMCU pin D7
+// Display DC (RS/AO)to NodeMCU pin D3
+// Display RESET     to NodeMCU pin D4 (or RST, see below)
+// Display CS        to NodeMCU pin D8 (or GND, see below)
+// Display GND       to NodeMCU pin GND (0V)
+// Display VCC       to NodeMCU 5V or 3.3V
+//
+// The TFT RESET pin can be connected to the NodeMCU RST pin or 3.3V to free up a control pin
+//
+// The DC (Data Command) pin may be labeled AO or RS (Register Select)
+//
+// With some displays such as the ILI9341 the TFT CS pin can be connected to GND if no more
+// SPI devices (e.g. an SD Card) are connected, in this case comment out the #define TFT_CS
+// line below so it is NOT defined. Other displays such at the ST7735 require the TFT CS pin
+// to be toggled during setup, so in these cases the TFT_CS line must be defined and connected.
+//
+// The NodeMCU D0 pin can be used for RST
+//
+//
+// Note: only some versions of the NodeMCU provide the USB 5V on the VIN pin
+// If 5V is not available at a pin you can use 3.3V but backlight brightness
+// will be lower.
+
+
+// ###### EDIT THE PIN NUMBERS IN THE LINES FOLLOWING TO SUIT YOUR ESP8266 SETUP ######
+
+// For NodeMCU - use pin numbers in the form PIN_Dx where Dx is the NodeMCU pin designation
+//#define TFT_CS   PIN_D8  // Chip select control pin D8
+//#define TFT_DC   PIN_D3  // Data Command control pin
+//#define TFT_RST  PIN_D4  // Reset pin (could connect to NodeMCU RST, see next line)
+//#define TFT_RST  -1    // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
+
+//#define TFT_BL PIN_D1  // LED back-light (only for ST7789 with backlight control pin)
+
+//#define TOUCH_CS PIN_D2     // Chip select pin (T_CS) of touch screen
+
+//#define TFT_WR PIN_D2       // Write strobe for modified Raspberry Pi TFT only
+
+
+// ######  FOR ESP8266 OVERLAP MODE EDIT THE PIN NUMBERS IN THE FOLLOWING LINES  ######
+
+// Overlap mode shares the ESP8266 FLASH SPI bus with the TFT so has a performance impact
+// but saves pins for other functions. It is best not to connect MISO as some displays
+// do not tristate that line wjen chip select is high!
+// On NodeMCU 1.0 SD0=MISO, SD1=MOSI, CLK=SCLK to connect to TFT in overlap mode
+// On NodeMCU V3  S0 =MISO, S1 =MOSI, S2 =SCLK
+// In ESP8266 overlap mode the following must be defined
+
+//#define TFT_SPI_OVERLAP
+
+// In ESP8266 overlap mode the TFT chip select MUST connect to pin D3
+//#define TFT_CS   PIN_D3
+//#define TFT_DC   PIN_D5  // Data Command control pin
+//#define TFT_RST  PIN_D4  // Reset pin (could connect to NodeMCU RST, see next line)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
+
+
+// ###### EDIT THE PIN NUMBERS IN THE LINES FOLLOWING TO SUIT YOUR ESP32 SETUP   ######
+
+// For ESP32 Dev board (only tested with ILI9341 display)
+// The hardware SPI can be mapped to any pins
+
+// Marauder Mini
+// Drone Detector v1
+
+#define TFT_CS   23  // Chip select control pin D8
+#define TFT_DC   24  // Data Command control pin
+#define TFT_RST  -1  // Reset pin (could connect to NodeMCU RST, see next line)
+#define TOUCH_CS -1
+//#define TFT_MISO 16
+#define TFT_MOSI 7
+#define TFT_SCLK 6
+#define TFT_BL   27
+
+
+// Drone Detector v2
+/*
+#define TFT_CS   17  // Chip select control pin D8
+#define TFT_DC   26  // Data Command control pin
+#define TFT_RST  -1  // Reset pin (could connect to NodeMCU RST, see next line)
+#define TOUCH_CS -1
+//#define TFT_MISO 16
+#define TFT_MOSI 23
+#define TFT_SCLK 18
+#define TFT_BL   32
+*/
+/*
+// ESP32 Marauder 
+#define TFT_MISO 19
+#define TFT_MOSI 23
+#define TFT_SCLK 18
+#define TFT_CS   17  // Chip select control pin
+#define TFT_DC   16  // Data Command control pin
+#define TFT_RST   5  // Reset pin (could connect to RST pin)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if display RESET is connected to ESP32 board RST
+
+#define TFT_BL   32  // LED back-light (only for ST7789 with backlight control pin)
+
+#define TOUCH_CS 21     // Chip select pin (T_CS) of touch screen
+*/
+/////////////////////////////
+
+// ESP32 Centauri
+/*
+#define TFT_MISO 19
+#define TFT_MOSI 23
+#define TFT_SCLK 18
+#define TFT_CS   27  // Chip select control pin
+#define TFT_DC   26  // Data Command control pin
+#define TFT_RST   5  // Reset pin (could connect to RST pin)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if display RESET is connected to ESP32 board RST
+
+#define TFT_BL   32  // LED back-light (only for ST7789 with backlight control pin)
+
+#define TOUCH_CS 21     // Chip select pin (T_CS) of touch screen
+*/
+/////////////////////////////
+
+//#define TFT_WR 22    // Write strobe for modified Raspberry Pi TFT only
+
+// For the M5Stack module use these #define lines
+//#define TFT_MISO 19
+//#define TFT_MOSI 23
+//#define TFT_SCLK 18
+//#define TFT_CS   14  // Chip select control pin
+//#define TFT_DC   27  // Data Command control pin
+//#define TFT_RST  33  // Reset pin (could connect to Arduino RESET pin)
+//#define TFT_BL   32  // LED back-light (required for M5Stack)
+
+// ######       EDIT THE PINs BELOW TO SUIT YOUR ESP32 PARALLEL TFT SETUP        ######
+
+// The library supports 8 bit parallel TFTs with the ESP32, the pin
+// selection below is compatible with ESP32 boards in UNO format.
+// Wemos D32 boards need to be modified, see diagram in Tools folder.
+// Only ILI9481 and ILI9341 based displays have been tested!
+
+// Parallel bus is only supported on ESP32
+// Uncomment line below to use ESP32 Parallel interface instead of SPI
+
+//#define ESP32_PARALLEL
+
+// The ESP32 and TFT the pins used for testing are:
+//#define TFT_CS   33  // Chip select control pin (library pulls permanently low
+//#define TFT_DC   15  // Data Command control pin - must use a pin in the range 0-31
+//#define TFT_RST  32  // Reset pin, toggles on startup
+
+//#define TFT_WR    4  // Write strobe control pin - must use a pin in the range 0-31
+//#define TFT_RD    2  // Read strobe control pin
+
+//#define TFT_D0   12  // Must use pins in the range 0-31 for the data bus
+//#define TFT_D1   13  // so a single register write sets/clears all bits.
+//#define TFT_D2   26  // Pins can be randomly assigned, this does not affect
+//#define TFT_D3   25  // TFT screen update performance.
+//#define TFT_D4   17
+//#define TFT_D5   16
+//#define TFT_D6   27
+//#define TFT_D7   14
+
+
+// ##################################################################################
+//
+// Section 3. Define the fonts that are to be used here
+//
+// ##################################################################################
+
+// Comment out the #defines below with // to stop that font being loaded
+// The ESP8366 and ESP32 have plenty of memory so commenting out fonts is not
+// normally necessary. If all fonts are loaded the extra FLASH space required is
+// about 17Kbytes. To save FLASH space only enable the fonts you need!
+
+#define LOAD_GLCD   // Font 1. Original Adafruit 8 pixel font needs ~1820 bytes in FLASH
+#define LOAD_FONT2  // Font 2. Small 16 pixel high font, needs ~3534 bytes in FLASH, 96 characters
+#define LOAD_FONT4  // Font 4. Medium 26 pixel high font, needs ~5848 bytes in FLASH, 96 characters
+#define LOAD_FONT6  // Font 6. Large 48 pixel font, needs ~2666 bytes in FLASH, only characters 1234567890:-.apm
+#define LOAD_FONT7  // Font 7. 7 segment 48 pixel font, needs ~2438 bytes in FLASH, only characters 1234567890:-.
+#define LOAD_FONT8  // Font 8. Large 75 pixel font needs ~3256 bytes in FLASH, only characters 1234567890:-.
+//#define LOAD_FONT8N // Font 8. Alternative to Font 8 above, slightly narrower, so 3 digits fit a 160 pixel TFT
+#define LOAD_GFXFF  // FreeFonts. Include access to the 48 Adafruit_GFX free fonts FF1 to FF48 and custom fonts
+
+// Comment out the #define below to stop the SPIFFS filing system and smooth font code being loaded
+// this will save ~20kbytes of FLASH
+#define SMOOTH_FONT
+
+
+// ##################################################################################
+//
+// Section 4. Other options
+//
+// ##################################################################################
+
+// Define the SPI clock frequency, this affects the graphics rendering speed. Too
+// fast and the TFT driver will not keep up and display corruption appears.
+// With an ILI9341 display 40MHz works OK, 80MHz sometimes fails
+// With a ST7735 display more than 27MHz may not work (spurious pixels and lines)
+// With an ILI9163 display 27 MHz works OK.
+
+// #define SPI_FREQUENCY   1000000
+//#define SPI_FREQUENCY   5000000
+// #define SPI_FREQUENCY  10000000
+// #define SPI_FREQUENCY  20000000
+#define SPI_FREQUENCY  27000000 // Marauder // Actually sets it to 26.67MHz = 80/3
+// #define SPI_FREQUENCY  40000000
+// #define SPI_FREQUENCY  80000000
+
+// Optional reduced SPI frequency for reading TFT
+//#define SPI_READ_FREQUENCY  20000000
+
+// The XPT2046 requires a lower SPI clock rate of 2.5MHz so we define that here:
+//#define SPI_TOUCH_FREQUENCY  2500000
+
+// The ESP32 has 2 free SPI ports i.e. VSPI and HSPI, the VSPI is the default.
+// If the VSPI port is in use and pins are not accessible (e.g. TTGO T-Beam)
+// then uncomment the following line:
+//#define USE_HSPI_PORT
+
+// Comment out the following #define if "SPI Transactions" do not need to be
+// supported. When commented out the code size will be smaller and sketches will
+// run slightly faster, so leave it commented out unless you need it!
+
+// Transaction support is needed to work with SD library but not needed with TFT_SdFat
+// Transaction support is required if other SPI devices are connected.
+
+// Transactions are automatically enabled by the library for an ESP32 (to use HAL mutex)
+// so changing it here has no effect
+
+// #define SUPPORT_TRANSACTIONS
--- a/esp32_marauder/Assets.h
+++ b/esp32_marauder/Assets.h
@@ -215,7 +215,19 @@ PROGMEM static const unsigned char menu_icons[][66] = {
    0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 
    0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 
    0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 
-    0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF}
+    0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF},
+    {0xFF, 0xFF, 0x3F, 0xFF, 0xF7, 0x3F, 0x7F, 0x96, 0x3F, 0xFF, 0xED, 0x3F, // PINESCAN_SNIFF: 37
+    0x3F, 0x25, 0x3F, 0xDF, 0xD2, 0x3E, 0xFF, 0xED, 0x3F, 0x7F, 0x8E, 0x3F, 
+    0x3B, 0x77, 0x37, 0xBD, 0x6A, 0x2F, 0xD6, 0xBD, 0x1A, 0xDA, 0xDA, 0x16, 
+    0x5A, 0x6F, 0x16, 0x9A, 0xF7, 0x16, 0xD6, 0x5A, 0x1A, 0xDD, 0xBD, 0x2E, 
+    0xBB, 0x5A, 0x37, 0x3F, 0x6F, 0x3F, 0x7F, 0xB7, 0x3F, 0xFF, 0xCC, 0x3F, 
+    0xFF, 0xF3, 0x3F, 0xFF, 0xFF, 0x3F},
+    {0xFF, 0xFF, 0xFF, 0xFF, 0x07, 0xFF, 0xFF, 0xFC, 0xFF, 0xF3, 0x87, 0xF7, // JOINED: 38
+    0x7F, 0xEE, 0xFF, 0xED, 0xC7, 0xDD, 0xBF, 0xDB, 0x7F, 0xDB, 0x67, 0xDB, 
+    0x67, 0xDB, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF},
+    {0xFF, 0xFF, 0x1F, 0xF8, 0x0F, 0xF0, 0x07, 0xE0, 0x07, 0xE0, 0x07, 0xE0, // FORCE: 39
+    0x67, 0xE6, 0x77, 0xEE, 0x87, 0xE0, 0x8F, 0xF1, 0x0F, 0xF0, 0x4F, 0xF5, 
+    0x1F, 0xF8, 0x3F, 0xFC, 0xFF, 0xFF, 0xFF, 0xFF}
 };

 /*#ifndef MARAUDER_MINI
--- a/esp32_marauder/CommandLine.cpp
+++ b/esp32_marauder/CommandLine.cpp
@@ -220,13 +220,19 @@ void CommandLine::runCommand(String input) {
    
    // WiFi sniff/scan
    Serial.println(HELP_EVIL_PORTAL_CMD);
+    Serial.println(HELP_PACKET_COUNT_CMD);
+    Serial.println(HELP_PING_CMD);
+    Serial.println(HELP_PORT_SCAN_CMD);
    Serial.println(HELP_SIGSTREN_CMD);
+    Serial.println(HELP_SCAN_ALL_CMD);
    Serial.println(HELP_SCANAP_CMD);
    Serial.println(HELP_SCANSTA_CMD);
    Serial.println(HELP_SNIFF_RAW_CMD);
    Serial.println(HELP_SNIFF_BEACON_CMD);
    Serial.println(HELP_SNIFF_PROBE_CMD);
    Serial.println(HELP_SNIFF_PWN_CMD);
+    Serial.println(HELP_SNIFF_PINESCAN_CMD);
+    Serial.println(HELP_SNIFF_MULTISSID_CMD);
    Serial.println(HELP_SNIFF_ESP_CMD);
    Serial.println(HELP_SNIFF_DEAUTH_CMD);
    Serial.println(HELP_SNIFF_PMKID_CMD);
@@ -239,15 +245,18 @@ void CommandLine::runCommand(String input) {
    Serial.println(HELP_ATTACK_CMD);
    
    // WiFi Aux
+    Serial.println(HELP_INFO_CMD);
    Serial.println(HELP_LIST_AP_CMD_A);
    Serial.println(HELP_LIST_AP_CMD_B);
    Serial.println(HELP_LIST_AP_CMD_C);
    Serial.println(HELP_LIST_AP_CMD_D);
+    Serial.println(HELP_LIST_AP_CMD_E);
    Serial.println(HELP_SEL_CMD_A);
    Serial.println(HELP_SSID_CMD_A);
    Serial.println(HELP_SSID_CMD_B);
    Serial.println(HELP_SAVE_CMD);
    Serial.println(HELP_LOAD_CMD);
+    Serial.println(HELP_JOIN_CMD);
    
    // Bluetooth sniff/scan
    #ifdef HAS_BT
@@ -277,9 +286,16 @@ void CommandLine::runCommand(String input) {
    //  web_obj.shutdownServer();
    //  return;
    //}
+
+    int f_arg = this->argSearch(&cmd_args, "-f");
    
    uint8_t old_scan_mode=wifi_scan_obj.currentScanMode;

+    if (f_arg != -1) {
+      WiFi.disconnect(true);
+      delay(100);
+    }
+
    wifi_scan_obj.StartScan(WIFI_SCAN_OFF);

    if(old_scan_mode == WIFI_SCAN_GPS_NMEA)
@@ -520,6 +536,16 @@ void CommandLine::runCommand(String input) {
        menu_function_obj.drawStatusBar();
      #endif
      wifi_scan_obj.StartScan(WIFI_SCAN_SIG_STREN, TFT_MAGENTA);
+      wifi_scan_obj.renderPacketRate();
+    }
+    // Packet count
+    else if (cmd_args.get(0) == PACKET_COUNT_CMD) {
+      Serial.println("Starting Packet Count Scan. Stop with " + (String)STOPSCAN_CMD);
+      #ifdef HAS_SCREEN
+        display_obj.clearScreen();
+        menu_function_obj.drawStatusBar();
+      #endif
+      wifi_scan_obj.StartScan(WIFI_SCAN_PACKET_RATE, TFT_ORANGE);
    }
    // Wardrive
    else if (cmd_args.get(0) == WARDRIVE_CMD) {
@@ -593,6 +619,10 @@ void CommandLine::runCommand(String input) {
        }
      }
    }
+    else if (cmd_args.get(0) == SCAN_ALL_CMD) {
+      Serial.println("Scanning for APs and Stations. Stop with " + (String)STOPSCAN_CMD);
+      wifi_scan_obj.StartScan(WIFI_SCAN_AP_STA, TFT_MAGENTA);
+    }
    else if (cmd_args.get(0) == SCANAP_CMD) {
      int full_sw = -1;
      #ifdef HAS_SCREEN
@@ -666,6 +696,24 @@ void CommandLine::runCommand(String input) {
      #endif
      wifi_scan_obj.StartScan(WIFI_SCAN_PWN, TFT_MAGENTA);
    }
+    // PineScan sniff
+    else if (cmd_args.get(0) == SNIFF_PINESCAN_CMD) {
+      Serial.println("Starting Pinescan sniff. Stop with " + (String)STOPSCAN_CMD);
+      #ifdef HAS_SCREEN
+        display_obj.clearScreen();
+        menu_function_obj.drawStatusBar();
+      #endif
+      wifi_scan_obj.StartScan(WIFI_SCAN_PINESCAN, TFT_MAGENTA);
+    }
+    // MultiSSID sniff
+    else if (cmd_args.get(0) == SNIFF_MULTISSID_CMD) {
+      Serial.println("Starting MultiSSID sniff. Stop with " + (String)STOPSCAN_CMD);
+      #ifdef HAS_SCREEN
+        display_obj.clearScreen();
+        menu_function_obj.drawStatusBar();
+      #endif
+      wifi_scan_obj.StartScan(WIFI_SCAN_MULTISSID, TFT_MAGENTA);
+    }
    // Espressif sniff
    else if (cmd_args.get(0) == SNIFF_ESP_CMD) {
      Serial.println("Starting Espressif device sniff. Stop with " + (String)STOPSCAN_CMD);
@@ -1123,6 +1171,52 @@ void CommandLine::runCommand(String input) {
    }
  }

+  if (wifi_scan_obj.wifi_connected) {
+    // Ping Scan
+    if (cmd_args.get(0) == PING_CMD) {
+      Serial.println("Starting Ping Scan. Stop with " + (String)STOPSCAN_CMD);
+      #ifdef HAS_SCREEN
+        display_obj.clearScreen();
+        menu_function_obj.drawStatusBar();
+      #endif
+      wifi_scan_obj.StartScan(WIFI_PING_SCAN, TFT_GREEN);
+    }
+
+    // Port Scan
+    if (cmd_args.get(0) == PORT_SCAN_CMD) {
+      int all_sw = this->argSearch(&cmd_args, "-a");
+      int ip_sw = this->argSearch(&cmd_args, "-t");
+
+      // Check they specified ip index
+      if (ip_sw != -1) {
+        int ip_index = cmd_args.get(ip_sw + 1).toInt();
+
+        // Check provided index is in list
+        if (ip_index < ipList->size()) {
+
+          // Full port scan
+          if (all_sw != -1) {
+            Serial.println("Selected: " + ipList->get(ip_index).toString());
+            wifi_scan_obj.current_scan_ip = ipList->get(ip_index);
+            #ifdef HAS_SCREEN
+              display_obj.clearScreen();
+              menu_function_obj.drawStatusBar();
+            #endif
+            wifi_scan_obj.StartScan(WIFI_PORT_SCAN_ALL, TFT_BLUE);
+          }
+        }
+        else {
+          Serial.println("The IP index specified is out of range");
+          return;
+        }
+      }
+      else {
+        Serial.println("You did not specify an IP index");
+        return;
+      }
+    }
+  }
+

  int count_selected = 0;
  //// WiFi aux commands
@@ -1132,6 +1226,7 @@ void CommandLine::runCommand(String input) {
    int ss_sw = this->argSearch(&cmd_args, "-s");
    int cl_sw = this->argSearch(&cmd_args, "-c");
    int at_sw = this->argSearch(&cmd_args, "-t");
+    int ip_sw = this->argSearch(&cmd_args, "-i");

    // List APs
    if (ap_sw != -1) {
@@ -1145,6 +1240,12 @@ void CommandLine::runCommand(String input) {
      }
      this->showCounts(count_selected);
    }
+    // List IPs
+    else if (ip_sw != -1) {
+      for (int i = 0; i < ipList->size(); i++) {
+        Serial.println("[" + (String)i + "] " + ipList->get(i).toString());
+      }
+    }
    // List SSIDs
    else if (ss_sw != -1) {
      for (int i = 0; i < ssids->size(); i++) {
@@ -1189,6 +1290,43 @@ void CommandLine::runCommand(String input) {
      return;
    }
  }
+  else if (cmd_args.get(0) == INFO_CMD) {
+    int ap_sw = this->argSearch(&cmd_args, "-a");
+
+    if (ap_sw != -1) {
+      int filter_ap = cmd_args.get(ap_sw + 1).toInt();
+      wifi_scan_obj.RunAPInfo(filter_ap, false);
+    }
+    else {
+      wifi_scan_obj.currentScanMode = SHOW_INFO;
+      #ifdef HAS_SCREEN
+        menu_function_obj.changeMenu(&menu_function_obj.infoMenu);
+      #endif
+      wifi_scan_obj.RunInfo();
+    }
+  }
+  else if (cmd_args.get(0) == JOIN_CMD) {
+    int ap_sw = this->argSearch(&cmd_args, "-a");
+    int pw_sw = this->argSearch(&cmd_args, "-p");
+
+    if ((ap_sw != -1) && (pw_sw != -1)) {
+      int index = cmd_args.get(ap_sw + 1).toInt();
+      String password = cmd_args.get(pw_sw + 1);
+      Serial.println("Using SSID: " + (String)access_points->get(index).essid + " Password: " + (String)password);
+      //wifi_scan_obj.currentScanMode = LV_JOIN_WIFI;
+      //wifi_scan_obj.StartScan(LV_JOIN_WIFI, TFT_YELLOW); 
+      wifi_scan_obj.joinWiFi(access_points->get(index).essid, password, false);
+      #ifdef HAS_SCREEN
+        #ifdef HAS_MINI_KB
+          menu_function_obj.changeMenu(menu_function_obj.current_menu);
+        #endif
+      #endif
+    }
+    else {
+      Serial.println("You did not provide the proper args");
+      return;
+    }
+  }
  // Select access points or stations
  else if (cmd_args.get(0) == SEL_CMD) {
    // Get switches
@@ -1313,26 +1451,43 @@ void CommandLine::runCommand(String input) {
      // Get list of indices
      LinkedList<String> ss_index = this->parseCommand(cmd_args.get(ss_sw + 1), ",");

-      // Mark APs as selected
-      for (int i = 0; i < ss_index.size(); i++) {
-        int index = ss_index.get(i).toInt();
-        if (!this->inRange(ssids->size(), index)) {
-          Serial.println("Index not in range: " + (String)index);
-          continue;
+      // Select ALL SSIDs
+      if (cmd_args.get(ss_sw + 1) == "all") {
+        for (int i = 0; i < ssids->size(); i++) {
+          if (ssids->get(i).selected) {
+            ssid new_ssid = ssids->get(i);
+            new_ssid.selected = false;
+            ssids->set(i, new_ssid);
+            count_unselected += 1;
+          }
+          else {
+            ssid new_ssid = ssids->get(i);
+            new_ssid.selected = true;
+            ssids->set(i, new_ssid);
+            count_selected += 1;
+          }
        }
-        if (ssids->get(index).selected) {
-          // Unselect "selected" ap
-          ssid new_ssid = ssids->get(index);
-          new_ssid.selected = false;
-          ssids->set(index, new_ssid);
-          count_unselected += 1;
-        }
-        else {
-          // Select "unselected" ap
-          ssid new_ssid = ssids->get(index);
-          new_ssid.selected = true;
-          ssids->set(index, new_ssid);
-          count_selected += 1;
+      }
+      else {
+      // Mark SSIDs as selected
+        for (int i = 0; i < ss_index.size(); i++) {
+          int index = ss_index.get(i).toInt();
+          if (!this->inRange(ssids->size(), index)) {
+            Serial.println("Index not in range: " + (String)index);
+            continue;
+          }
+          if (ssids->get(index).selected) {
+            ssid new_ssid = ssids->get(index);
+            new_ssid.selected = false;
+            ssids->set(index, new_ssid);
+            count_unselected += 1;
+          }
+          else {
+            ssid new_ssid = ssids->get(index);
+            new_ssid.selected = true;
+            ssids->set(index, new_ssid);
+            count_selected += 1;
+          }
        }
      }
      this->showCounts(count_selected, count_unselected);
--- a/esp32_marauder/CommandLine.h
+++ b/esp32_marauder/CommandLine.h
@@ -34,6 +34,7 @@ extern LinkedList<AccessPoint>* access_points;
 extern LinkedList<AirTag>* airtags;
 extern LinkedList<ssid>* ssids;
 extern LinkedList<Station>* stations;
+extern LinkedList<IPAddress>* ipList;
 extern const String PROGMEM version_number;
 extern const String PROGMEM board_target;

@@ -54,18 +55,24 @@ const char PROGMEM NMEA_CMD[] = "nmea";

 // WiFi sniff/scan
 const char PROGMEM EVIL_PORTAL_CMD[] = "evilportal";
+const char PROGMEM PACKET_COUNT_CMD[] = "packetcount";
 const char PROGMEM SIGSTREN_CMD[] = "sigmon";
+const char PROGMEM SCAN_ALL_CMD[] = "scanall";
 const char PROGMEM SCANAP_CMD[] = "scanap";
 const char PROGMEM SCANSTA_CMD[] = "scansta";
 const char PROGMEM SNIFF_RAW_CMD[] = "sniffraw";
 const char PROGMEM SNIFF_BEACON_CMD[] = "sniffbeacon";
 const char PROGMEM SNIFF_PROBE_CMD[] = "sniffprobe";
 const char PROGMEM SNIFF_PWN_CMD[] = "sniffpwn";
+const char PROGMEM SNIFF_PINESCAN_CMD[] = "sniffpinescan";
+const char PROGMEM SNIFF_MULTISSID_CMD[] = "sniffmultissid";
 const char PROGMEM SNIFF_ESP_CMD[] = "sniffesp";
 const char PROGMEM SNIFF_DEAUTH_CMD[] = "sniffdeauth";
 const char PROGMEM SNIFF_PMKID_CMD[] = "sniffpmkid";
 const char PROGMEM STOPSCAN_CMD[] = "stopscan";
 const char PROGMEM WARDRIVE_CMD[] = "wardrive";
+const char PROGMEM PING_CMD[] = "pingscan";
+const char PROGMEM PORT_SCAN_CMD[] = "portscan";

 // WiFi attack
 const char PROGMEM ATTACK_CMD[] = "attack";
@@ -76,10 +83,12 @@ const char PROGMEM ATTACK_TYPE_RR[] = "rickroll";

 // WiFi Aux
 const char PROGMEM LIST_AP_CMD[] = "list";
+const char PROGMEM INFO_CMD[] = "info";
 const char PROGMEM SEL_CMD[] = "select";
 const char PROGMEM SSID_CMD[] = "ssid";
 const char PROGMEM SAVE_CMD[] = "save";
 const char PROGMEM LOAD_CMD[] = "load";
+const char PROGMEM JOIN_CMD[] = "join";

 // Bluetooth sniff/scan
 const char PROGMEM BT_SPAM_CMD[] = "blespam";
@@ -109,18 +118,24 @@ const char PROGMEM HELP_NMEA_CMD[] = "nmea";

 // WiFi sniff/scan
 const char PROGMEM HELP_EVIL_PORTAL_CMD[] = "evilportal [-c start [-w html.html]/sethtml <html.html>]";
+const char PROGMEM HELP_PACKET_COUNT_CMD[] = "packetcount";
 const char PROGMEM HELP_SIGSTREN_CMD[] = "sigmon";
+const char PROGMEM HELP_SCAN_ALL_CMD[] = "scanall";
 const char PROGMEM HELP_SCANAP_CMD[] = "scanap";
 const char PROGMEM HELP_SCANSTA_CMD[] = "scansta";
 const char PROGMEM HELP_SNIFF_RAW_CMD[] = "sniffraw";
 const char PROGMEM HELP_SNIFF_BEACON_CMD[] = "sniffbeacon";
 const char PROGMEM HELP_SNIFF_PROBE_CMD[] = "sniffprobe";
 const char PROGMEM HELP_SNIFF_PWN_CMD[] = "sniffpwn";
+const char PROGMEM HELP_SNIFF_PINESCAN_CMD[] = "sniffpinescan";
+const char PROGMEM HELP_SNIFF_MULTISSID_CMD[] = "sniffmultissid";
 const char PROGMEM HELP_SNIFF_ESP_CMD[] = "sniffesp";
 const char PROGMEM HELP_SNIFF_DEAUTH_CMD[] = "sniffdeauth";
 const char PROGMEM HELP_SNIFF_PMKID_CMD[] = "sniffpmkid [-c <channel>][-d][-l]";
-const char PROGMEM HELP_STOPSCAN_CMD[] = "stopscan";
+const char PROGMEM HELP_STOPSCAN_CMD[] = "stopscan [-f]";
 const char PROGMEM HELP_WARDRIVE_CMD[] = "wardrive [-s]";
+const char PROGMEM HELP_PING_CMD[] = "pingscan";
+const char PROGMEM HELP_PORT_SCAN_CMD[] = "portscan [-a] -t <ip index>";

 // WiFi attack
 const char PROGMEM HELP_ATTACK_CMD[] = "attack -t <beacon [-l/-r/-a]/deauth [-c]/[-s <src mac>] [-d <dst mac>]/probe/rickroll>";
@@ -130,11 +145,14 @@ const char PROGMEM HELP_LIST_AP_CMD_A[] = "list -s";
 const char PROGMEM HELP_LIST_AP_CMD_B[] = "list -a";
 const char PROGMEM HELP_LIST_AP_CMD_C[] = "list -c";
 const char PROGMEM HELP_LIST_AP_CMD_D[] = "list -t";
+const char PROGMEM HELP_LIST_AP_CMD_E[] = "list -i";
+const char PROGMEM HELP_INFO_CMD[] = "info [-a <index>]";
 const char PROGMEM HELP_SEL_CMD_A[] = "select -a/-s/-c <index (comma separated)>/-f \"equals <String> or contains <String>\"";
 const char PROGMEM HELP_SSID_CMD_A[] = "ssid -a [-g <count>/-n <name>]";
 const char PROGMEM HELP_SSID_CMD_B[] = "ssid -r <index>";
 const char PROGMEM HELP_SAVE_CMD[] = "save -a/-s";
 const char PROGMEM HELP_LOAD_CMD[] = "load -a/-s";
+const char PROGMEM HELP_JOIN_CMD[] = "join -a <index> -p <password>";

 // Bluetooth sniff/scan
 const char PROGMEM HELP_BT_SNIFF_CMD[] = "sniffbt [-t] <airtag/flipper>";
--- a/esp32_marauder/Display.cpp
+++ b/esp32_marauder/Display.cpp
@@ -4,9 +4,111 @@
 #ifdef HAS_SCREEN

 Display::Display()
+#ifdef HAS_CYD_TOUCH
+  : touchscreenSPI(VSPI),
+    touchscreen(XPT2046_CS, XPT2046_IRQ)
+#endif
 {
 }

+int8_t Display::menuButton(uint16_t *x, uint16_t *y, bool pressed, bool check_hold) {
+  #ifdef HAS_ILI9341
+    for (uint8_t b = BUTTON_ARRAY_LEN; b < BUTTON_ARRAY_LEN + 3; b++) {
+      if (pressed && this->key[b].contains(*x, *y)) {
+        this->key[b].press(true);  // tell the button it is pressed
+      } else {
+        this->key[b].press(false);  // tell the button it is NOT pressed
+      }
+    }
+
+    for (uint8_t b = BUTTON_ARRAY_LEN; b < BUTTON_ARRAY_LEN + 3; b++) {
+      if (!check_hold) {
+        if ((this->key[b].justReleased()) && (!pressed)) {
+          return b - BUTTON_ARRAY_LEN;
+        }
+      }
+      else {
+        if ((this->key[b].isPressed())) {
+          return b - BUTTON_ARRAY_LEN;
+        }
+      }
+    }
+
+  #endif
+
+  return -1;
+}
+
+uint8_t Display::updateTouch(uint16_t *x, uint16_t *y, uint16_t threshold) {
+  #ifdef HAS_ILI9341
+    if (!this->headless_mode)
+      #ifndef HAS_CYD_TOUCH
+        return this->tft.getTouch(x, y, threshold);
+      #else
+        if (this->touchscreen.tirqTouched() && this->touchscreen.touched()) {
+          TS_Point p = this->touchscreen.getPoint();
+
+          //*x = map(p.x, 200, 3700, 1, TFT_WIDTH);
+          //*y = map(p.y, 240, 3800, 1, TFT_HEIGHT);
+
+          uint8_t rot = this->tft.getRotation();
+
+          //#ifdef HAS_CYD_PORTRAIT
+          //  rot = 0;
+          //#endif
+
+          switch (rot) {
+            case 0: // Standard Protrait
+              *x = map(p.x, 200, 3700, 1, TFT_WIDTH);
+              *y = map(p.y, 240, 3800, 1, TFT_HEIGHT);
+              break;
+            case 1:
+              *x = map(p.y, 143, 3715, 0, TFT_HEIGHT);     // Horizontal (Y axis in touch, X on screen)
+              *y = map(p.x, 3786, 216, 0, TFT_WIDTH);    // Vertical (X axis in touch, Y on screen)
+              break;
+            case 2:
+              *x = map(p.x, 3700, 200, 1, TFT_WIDTH);
+              *y = map(p.y, 3800, 240, 1, TFT_HEIGHT);
+              break;
+            case 3:
+              *x = map(p.y, 3800, 240, 1, TFT_WIDTH);
+              *y = map(p.x, 200, 3700, 1, TFT_HEIGHT);
+              break;
+          }
+          return 1;
+        }
+        else
+          return 0;
+      #endif
+    else
+      return !this->headless_mode;
+  #endif
+
+  return 0;
+}
+
+bool Display::isTouchHeld(uint16_t threshold) {
+  static unsigned long touchStartTime = 0;
+  static bool touchHeld = false;
+  uint16_t x, y;
+
+  if (this->updateTouch(&x, &y, threshold)) {
+    // Touch detected
+    if (touchStartTime == 0) {
+      touchStartTime = millis();  // First touch timestamp
+    } else if (!touchHeld && millis() - touchStartTime >= 1000) {
+      touchHeld = true;  // Held for at least 1000ms
+      return true;
+    }
+  } else {
+    // Touch released
+    touchStartTime = 0;
+    touchHeld = false;
+  }
+
+  return false;
+}
+
 // Function to prepare the display and the menus
 void Display::RunSetup()
 {
@@ -18,42 +120,34 @@ void Display::RunSetup()
  #ifdef SCREEN_BUFFER
    screen_buffer = new LinkedList<String>();
  #endif
+
+  #ifdef HAS_CYD_TOUCH
+    this->touchscreenSPI.begin(XPT2046_CLK, XPT2046_MISO, XPT2046_MOSI, XPT2046_CS);
+    this->touchscreen.begin(touchscreenSPI);
+    this->touchscreen.setRotation(0);
+  #endif
  
  tft.init();
-  #ifndef MARAUDER_M5STICKC
-    tft.setRotation(0); // Portrait
-  #endif

-  #ifdef MARAUDER_M5STICKC
-    tft.setRotation(1);
-  #endif
-
-  #ifdef MARAUDER_REV_FEATHER
-    tft.setRotation(1);
-  #endif
+  tft.setRotation(SCREEN_ORIENTATION);

  tft.setCursor(0, 0);

  #ifdef HAS_ILI9341

-    #ifdef TFT_SHIELD
-      uint16_t calData[5] = { 275, 3494, 361, 3528, 4 }; // tft.setRotation(0); // Portrait with TFT Shield
-      //Serial.println(F("Using TFT Shield"));
-    #else if defined(TFT_DIY)
-      uint16_t calData[5] = { 339, 3470, 237, 3438, 2 }; // tft.setRotation(0); // Portrait with DIY TFT
-      //Serial.println(F("Using TFT DIY"));
+    #ifndef HAS_CYD_TOUCH
+      #ifdef TFT_SHIELD
+        uint16_t calData[5] = { 275, 3494, 361, 3528, 4 }; // tft.setRotation(0); // Portrait with TFT Shield
+      #elif defined(TFT_DIY)
+        uint16_t calData[5] = { 339, 3470, 237, 3438, 2 }; // tft.setRotation(0); // Portrait with DIY TFT
+      #endif
+      tft.setTouch(calData);
    #endif
-    tft.setTouch(calData);

  #endif

-  //tft.fillScreen(TFT_BLACK);
  clearScreen();

-  //Serial.println("SPI_FREQUENCY: " + (String)SPI_FREQUENCY);
-  //Serial.println("SPI_READ_FREQUENCY:" + (String)SPI_READ_FREQUENCY);
-  //Serial.println("SPI_TOUCH_FREQUENCY: " + (String)SPI_TOUCH_FREQUENCY);
-
  #ifdef KIT
    pinMode(KIT_LED_BUILTIN, OUTPUT);
  #endif
@@ -189,31 +283,56 @@ void Display::tftDrawYScaleButtons(byte y_scale)
  key[3].drawButton();
 }

-void Display::tftDrawChannelScaleButtons(int set_channel)
+void Display::tftDrawChannelScaleButtons(int set_channel, bool lnd_an)
 {
-  tft.drawFastVLine(178, 0, 20, TFT_WHITE);
-  tft.setCursor(145, 21); tft.setTextColor(TFT_WHITE); tft.setTextSize(1); tft.print(text10); tft.print(set_channel);
+  if (lnd_an) {
+    tft.drawFastVLine(178, 0, 20, TFT_WHITE);
+    tft.setCursor(145, 21); tft.setTextColor(TFT_WHITE); tft.setTextSize(1); tft.print(text10); tft.print(set_channel);

-  key[4].initButton(&tft, // channel - box
-                        164,
-                        10, // x, y, w, h, outline, fill, text
-                        20,
-                        20,
-                        TFT_BLACK, // Outline
-                        TFT_BLUE, // Fill
-                        TFT_BLACK, // Text
-                        "-",
-                        2);
-  key[5].initButton(&tft, // channel + box
-                        193,
-                        10, // x, y, w, h, outline, fill, text
-                        20,
-                        20,
-                        TFT_BLACK, // Outline
-                        TFT_BLUE, // Fill
-                        TFT_BLACK, // Text
-                        "+",
-                        2);
+    key[4].initButton(&tft, // channel - box
+                          164,
+                          10, // x, y, w, h, outline, fill, text
+                          EXT_BUTTON_WIDTH,
+                          EXT_BUTTON_WIDTH,
+                          TFT_BLACK, // Outline
+                          TFT_BLUE, // Fill
+                          TFT_BLACK, // Text
+                          "-",
+                          2);
+    key[5].initButton(&tft, // channel + box
+                          193,
+                          10, // x, y, w, h, outline, fill, text
+                          EXT_BUTTON_WIDTH,
+                          EXT_BUTTON_WIDTH,
+                          TFT_BLACK, // Outline
+                          TFT_BLUE, // Fill
+                          TFT_BLACK, // Text
+                          "+",
+                          2);
+  }
+
+  else {
+    key[4].initButton(&tft, // channel - box
+                          (EXT_BUTTON_WIDTH / 2) * 6,
+                          (STATUS_BAR_WIDTH * 2) + CHAR_WIDTH - 1, // x, y, w, h, outline, fill, text
+                          EXT_BUTTON_WIDTH,
+                          EXT_BUTTON_WIDTH,
+                          TFT_BLACK, // Outline
+                          TFT_BLUE, // Fill
+                          TFT_BLACK, // Text
+                          "-",
+                          2);
+    key[5].initButton(&tft, // channel + box
+                          (EXT_BUTTON_WIDTH / 2) * 10,
+                          (STATUS_BAR_WIDTH * 2) + CHAR_WIDTH - 1, // x, y, w, h, outline, fill, text
+                          EXT_BUTTON_WIDTH,
+                          EXT_BUTTON_WIDTH,
+                          TFT_BLACK, // Outline
+                          TFT_BLUE, // Fill
+                          TFT_BLACK, // Text
+                          "+",
+                          2);
+  }

  key[4].setLabelDatum(1, 5, MC_DATUM);
  key[5].setLabelDatum(1, 5, MC_DATUM);
@@ -222,21 +341,37 @@ void Display::tftDrawChannelScaleButtons(int set_channel)
  key[5].drawButton();
 }

-void Display::tftDrawExitScaleButtons()
+void Display::tftDrawExitScaleButtons(bool lnd_an)
 {
  //tft.drawFastVLine(178, 0, 20, TFT_WHITE);
  //tft.setCursor(145, 21); tft.setTextColor(TFT_WHITE); tft.setTextSize(1); tft.print("Channel:"); tft.print(set_channel);

-  key[6].initButton(&tft, // Exit box
-                        137,
-                        10, // x, y, w, h, outline, fill, text
-                        20,
-                        20,
-                        TFT_ORANGE, // Outline
-                        TFT_RED, // Fill
-                        TFT_BLACK, // Text
-                        "X",
-                        2);
+  if (lnd_an) {
+
+    key[6].initButton(&tft, // Exit box
+                      137,
+                      10, // x, y, w, h, outline, fill, text
+                      EXT_BUTTON_WIDTH,
+                      EXT_BUTTON_WIDTH,
+                      TFT_ORANGE, // Outline
+                      TFT_RED, // Fill
+                      TFT_BLACK, // Text
+                      "X",
+                      2);
+  }
+
+  else {
+    key[6].initButton(&tft, // Exit box
+                      EXT_BUTTON_WIDTH / 2,
+                      (STATUS_BAR_WIDTH * 2) + CHAR_WIDTH - 1, // x, y, w, h, outline, fill, text
+                      EXT_BUTTON_WIDTH,
+                      EXT_BUTTON_WIDTH,
+                      TFT_ORANGE, // Outline
+                      TFT_RED, // Fill
+                      TFT_BLACK, // Text
+                      "X",
+                      2);
+  }

  key[6].setLabelDatum(1, 5, MC_DATUM);

@@ -270,8 +405,13 @@ void Display::touchToExit()
 void Display::clearScreen()
 {
  //Serial.println(F("clearScreen()"));
-  tft.fillScreen(TFT_BLACK);
-  tft.setCursor(0, 0);
+  #ifndef MARAUDER_V7
+    tft.fillScreen(TFT_BLACK);
+    tft.setCursor(0, 0);
+  #else
+    tft.fillRect(0, 0, TFT_WIDTH, TFT_HEIGHT, TFT_BLACK);
+    tft.setCursor(0, 0);
+  #endif
 }

 #ifdef SCREEN_BUFFER
@@ -340,7 +480,7 @@ void Display::displayBuffer(bool do_clear)
          blank[(18+(yStart - TOP_FIXED_AREA_2) / TEXT_HEIGHT)%19] = xPos;
      #else
        xPos = 0;
-        if (this->screen_buffer->size() >= MAX_SCREEN_BUFFER) 
+        if (this->screen_buffer->size() >= MAX_SCREEN_BUFFER)
          this->scrollScreenBuffer();

        screen_buffer->add(display_buffer->shift());
@@ -348,14 +488,10 @@ void Display::displayBuffer(bool do_clear)
        for (int i = 0; i < this->screen_buffer->size(); i++) {
          tft.setCursor(xPos, (i * 12) + (SCREEN_HEIGHT / 6));
          String spaces = String(' ', TFT_WIDTH / CHAR_WIDTH);
-          //for (int x = 0; x < TFT_WIDTH / CHAR_WIDTH; x++)
-          //  tft.print(" ");
          tft.print(spaces);
          tft.setCursor(xPos, (i * 12) + (SCREEN_HEIGHT / 6));

          this->processAndPrintString(tft, this->screen_buffer->get(i));
-          //tft.setTextColor(TFT_GREEN, TFT_BLACK);
-          //tft.print(this->screen_buffer->get(i));
        }
      #endif

@@ -434,7 +570,11 @@ void Display::setupScrollArea(uint16_t tfa, uint16_t bfa) {
  //Serial.println("   bfa: " + (String)bfa);
  //Serial.println("yStart: " + (String)this->yStart);
  #ifdef HAS_ILI9341
-    tft.writecommand(ILI9341_VSCRDEF); // Vertical scroll definition
+    #ifdef HAS_ST7789
+      tft.writecommand(ST7789_VSCRDEF); // Vertical scroll definition
+    #else
+      tft.writecommand(ILI9341_VSCRDEF);
+    #endif
    tft.writedata(tfa >> 8);           // Top Fixed Area line count
    tft.writedata(tfa);
    tft.writedata((YMAX-tfa-bfa)>>8);  // Vertical Scrolling Area line count
@@ -447,7 +587,11 @@ void Display::setupScrollArea(uint16_t tfa, uint16_t bfa) {

 void Display::scrollAddress(uint16_t vsp) {
  #ifdef HAS_ILI9341
-    tft.writecommand(ILI9341_VSCRSADD); // Vertical scrolling pointer
+    #ifdef HAS_ST7789
+      tft.writecommand(ST7789_VSCRDEF); // Vertical scroll definition
+    #else
+      tft.writecommand(ILI9341_VSCRDEF);
+    #endif
    tft.writedata(vsp>>8);
    tft.writedata(vsp);
  #endif
@@ -567,7 +711,7 @@ void Display::drawStylus()
 //====================================================================================
 //   Decode and render the Jpeg image onto the TFT screen
 //====================================================================================
-void Display::jpegRender(int xpos, int ypos) {
+/*void Display::jpegRender(int xpos, int ypos) {

  // retrieve infomration about the image
  uint16_t  *pImg;
@@ -634,13 +778,13 @@ void Display::jpegRender(int xpos, int ypos) {

  // calculate how long it took to draw the image
  drawTime = millis() - drawTime; // Calculate the time it took
-}
+}*/

 //====================================================================================
 //   Print information decoded from the Jpeg image
 //====================================================================================
-void Display::jpegInfo() {
-/*
+/*void Display::jpegInfo() {
+
  Serial.println("===============");
  Serial.println("JPEG image info");
  Serial.println("===============");
@@ -654,13 +798,12 @@ void Display::jpegInfo() {
  Serial.print  ("MCU height :"); Serial.println(JpegDec.MCUHeight);
  Serial.println("===============");
  Serial.println("");
-  */
-}
+}*/

 //====================================================================================
 //   Open a Jpeg file and send it to the Serial port in a C array compatible format
 //====================================================================================
-void createArray(const char *filename) {
+/*void createArray(const char *filename) {

  // Open the named file
  fs::File jpgFile = SPIFFS.open( filename, "r");    // File handle reference for SPIFFS
@@ -700,7 +843,7 @@ void createArray(const char *filename) {

  Serial.println("};\r\n");
  jpgFile.close();
-}
+}*/

 // End JPEG_functions

--- a/esp32_marauder/Display.h
+++ b/esp32_marauder/Display.h
@@ -9,7 +9,7 @@

 #include <FS.h>
 #include <functional>
-#include <JPEGDecoder.h>
+//#include <JPEGDecoder.h>
 #include <LinkedList.h>
 #include <SPI.h>
 #include <lvgl.h>
@@ -19,6 +19,10 @@

 #include <TFT_eSPI.h>

+#ifdef HAS_CYD_TOUCH
+  #include <XPT2046_Touchscreen.h>
+#endif
+
 // WiFi stuff
 #define OTA_UPDATE 100
 #define SHOW_INFO 101
@@ -45,6 +49,10 @@
 #define MAGENTA_KEY ";mgn;"
 #define WHITE_KEY ";wht;"

+#define UP_BUTTON     0
+#define SELECT_BUTTON 1
+#define DOWN_BUTTON   2
+
 class Display
 {
  private:
@@ -69,9 +77,14 @@ class Display
  public:
    Display();
    TFT_eSPI tft = TFT_eSPI();
-    TFT_eSPI_Button key[BUTTON_ARRAY_LEN];
+    TFT_eSPI_Button key[BUTTON_ARRAY_LEN + 3];
    const String PROGMEM version_number = MARAUDER_VERSION;

+    #ifdef HAS_CYD_TOUCH
+      SPIClass touchscreenSPI;
+      XPT2046_Touchscreen touchscreen;
+    #endif
+
    bool printing = false;
    bool loading = false;
    bool tteBar = false;
@@ -105,6 +118,9 @@ class Display
    // We can speed up scrolling of short text lines by just blanking the character we drew
    int blank[19]; // We keep all the strings pixel lengths to optimise the speed of the top line blanking

+    int8_t menuButton(uint16_t *x, uint16_t *y, bool pressed, bool check_hold = false);
+    uint8_t updateTouch(uint16_t *x, uint16_t *y, uint16_t threshold = 600);
+    bool isTouchHeld(uint16_t threshold = 600);
    void tftDrawRedOnOffButton();
    void tftDrawGreenOnOffButton();
    void tftDrawGraphObjects(byte x_scale);
@@ -112,16 +128,16 @@ class Display
    void tftDrawColorKey();
    void tftDrawXScaleButtons(byte x_scale);
    void tftDrawYScaleButtons(byte y_scale);
-    void tftDrawChannelScaleButtons(int set_channel);
-    void tftDrawExitScaleButtons();
+    void tftDrawChannelScaleButtons(int set_channel, bool lnd_an = true);
+    void tftDrawExitScaleButtons(bool lnd_an = true);
    void buildBanner(String msg, int xpos);
    void clearScreen();
    void displayBuffer(bool do_clear = false);
    //void drawJpeg(const char *filename, int xpos, int ypos);
    void getTouchWhileFunction(bool pressed);
    void initScrollValues(bool tte = false);
-    void jpegInfo();
-    void jpegRender(int xpos, int ypos);
+    //void jpegInfo();
+    //void jpegRender(int xpos, int ypos);
    void listDir(fs::FS &fs, const char * dirname, uint8_t levels);
    void listFiles();
    void main(uint8_t scan_mode);
--- a/esp32_marauder/EvilPortal.cpp
+++ b/esp32_marauder/EvilPortal.cpp
@@ -1,5 +1,9 @@
 #include "EvilPortal.h"

+#ifdef HAS_PSRAM
+  char* index_html = nullptr;
+#endif
+
 AsyncWebServer server(80);

 EvilPortal::EvilPortal() {
@@ -14,8 +18,6 @@ void EvilPortal::setup() {

  html_files = new LinkedList<String>();

-  html_files->add("Back");
-
  #ifdef HAS_SD
    if (sd_obj.supported) {
      sd_obj.listDirToLinkedList(html_files, "/", "html");
@@ -25,6 +27,13 @@ void EvilPortal::setup() {
  #endif
 }

+void EvilPortal::cleanup() {
+  #ifdef HAS_PSRAM
+    free(index_html);
+    index_html = nullptr;
+  #endif
+}
+
 bool EvilPortal::begin(LinkedList<ssid>* ssids, LinkedList<AccessPoint>* access_points) {
  if (!this->setAP(ssids, access_points))
    return false;
@@ -45,12 +54,50 @@ String EvilPortal::get_password() {
 }

 void EvilPortal::setupServer() {
-  server.on("/", HTTP_GET, [this](AsyncWebServerRequest *request) {
-    request->send_P(200, "text/html", index_html);
-    Serial.println("client connected");
-    #ifdef HAS_SCREEN
-      this->sendToDisplay("Client connected to server");
+  #ifndef HAS_PSRAM
+    server.on("/", HTTP_GET, [this](AsyncWebServerRequest *request) {
+      request->send_P(200, "text/html", index_html);
+      Serial.println("client connected");
+      #ifdef HAS_SCREEN
+        this->sendToDisplay("Client connected to server");
+      #endif
+    });
+  #else
+    server.on("/", HTTP_GET, [this](AsyncWebServerRequest *request) {
+      request->send(200, "text/html", index_html);
+      Serial.println("client connected");
+      #ifdef HAS_SCREEN
+        this->sendToDisplay("Client connected to server");
+      #endif
+    });
+  #endif
+
+  const char* captiveEndpoints[] = {
+    "/hotspot-detect.html",
+    "/library/test/success.html",
+    "/success.txt",
+    "/generate_204",
+    "/gen_204",
+    "/ncsi.txt",
+    "/connecttest.txt",
+    "/redirect"
+  };
+
+  for (int i = 0; i < sizeof(captiveEndpoints) / sizeof(captiveEndpoints[0]); i++) {
+    
+    #ifndef HAS_PSRAM
+      server.on(captiveEndpoints[i], HTTP_GET, [this](AsyncWebServerRequest *request){
+        request->send_P(200, "text/html", index_html);
+      });
+    #else
+      server.on(captiveEndpoints[i], HTTP_GET, [this](AsyncWebServerRequest *request){
+        request->send(200, "text/html", index_html);
+      });
    #endif
+  }
+
+  server.on("/get-ap-name", HTTP_GET, [this](AsyncWebServerRequest *request) {
+    request->send(200, "text/plain", WiFi.softAPSSID());
  });

  server.on("/get", HTTP_GET, [this](AsyncWebServerRequest *request) {
@@ -80,7 +127,13 @@ void EvilPortal::setupServer() {
 void EvilPortal::setHtmlFromSerial() {
  Serial.println("Setting HTML from serial...");
  const char *htmlStr = Serial.readString().c_str();
-  strncpy(index_html, htmlStr, strlen(htmlStr));
+  #ifdef HAS_PSRAM
+    index_html = (char*) ps_malloc(MAX_HTML_SIZE);
+  #endif
+  strlcpy(index_html, htmlStr, strlen(htmlStr));
+  #ifdef HAS_PSRAM
+    index_html[MAX_HTML_SIZE - 1] = '\0';
+  #endif
  this->has_html = true;
  this->using_serial_html = true;
  Serial.println("html set");
@@ -121,7 +174,13 @@ bool EvilPortal::setHtml() {
      if (isPrintable(c))
        html.concat(c);
    }
-    strncpy(index_html, html.c_str(), strlen(html.c_str()));
+    #ifdef HAS_PSRAM
+      index_html = (char*) ps_malloc(MAX_HTML_SIZE);
+    #endif
+    strlcpy(index_html, html.c_str(), strlen(html.c_str()));
+    #ifdef HAS_PSRAM
+      index_html[MAX_HTML_SIZE - 1] = '\0';
+    #endif
    this->has_html = true;
    Serial.println("html set");
    html_file.close();
--- a/esp32_marauder/EvilPortal.h
+++ b/esp32_marauder/EvilPortal.h
@@ -33,11 +33,16 @@ extern Buffer buffer_obj;
 #define RESET_CMD "reset"
 #define START_CMD "start"
 #define ACK_CMD "ack"
-#define MAX_AP_NAME_SIZE 30
+#define MAX_AP_NAME_SIZE 32
 #define WIFI_SCAN_EVIL_PORTAL 30

 char apName[MAX_AP_NAME_SIZE] = "PORTAL";
-char index_html[MAX_HTML_SIZE] = "TEST";
+
+#ifndef HAS_PSRAM
+  char index_html[MAX_HTML_SIZE] = "TEST";
+#else
+  extern char* index_html;
+#endif

 struct ssid {
  String essid;
@@ -51,9 +56,14 @@ struct AccessPoint {
  uint8_t channel;
  uint8_t bssid[6];
  bool selected;
-  LinkedList<char>* beacon;
-  char rssi;
+ // LinkedList<char>* beacon;
+  char beacon[2];
+  int8_t rssi;
  LinkedList<uint16_t>* stations;
+  uint16_t packets;
+  uint8_t sec;
+  bool wps;
+  String man;
 };

 class CaptiveRequestHandler : public AsyncWebHandler {
@@ -102,6 +112,7 @@ class EvilPortal {

    LinkedList<String>* html_files;

+    void cleanup();
    String get_user_name();
    String get_password();
    void setup();
--- a/esp32_marauder/Keyboard.cpp
+++ b/esp32_marauder/Keyboard.cpp
@@ -0,0 +1,269 @@
+#include "Keyboard.h"
+
+#ifdef MARAUDER_CARDPUTER
+#include <driver/gpio.h>
+#include <Arduino.h>
+
+#define digitalWrite(pin, level) gpio_set_level((gpio_num_t)pin, level)
+#define digitalRead(pin) gpio_get_level((gpio_num_t)pin)
+
+void Keyboard_Class::_set_output(const std::vector<int> &pinList,
+                                 uint8_t output)
+{
+    output = output & 0B00000111;
+
+    digitalWrite(pinList[0], (output & 0B00000001));
+    digitalWrite(pinList[1], (output & 0B00000010));
+    digitalWrite(pinList[2], (output & 0B00000100));
+}
+
+uint8_t Keyboard_Class::_get_input(const std::vector<int> &pinList)
+{
+    uint8_t buffer = 0x00;
+    uint8_t pin_value = 0x00;
+
+    for (int i = 0; i < 7; i++)
+    {
+        pin_value = (digitalRead(pinList[i]) == 1) ? 0x00 : 0x01;
+        pin_value = pin_value << i;
+        buffer = buffer | pin_value;
+    }
+
+    return buffer;
+}
+
+void Keyboard_Class::begin()
+{
+    for (auto i : output_list)
+    {
+        gpio_reset_pin((gpio_num_t)i);
+        gpio_set_direction((gpio_num_t)i, GPIO_MODE_OUTPUT);
+        gpio_set_pull_mode((gpio_num_t)i, GPIO_PULLUP_PULLDOWN);
+        digitalWrite(i, 0);
+    }
+
+    for (auto i : input_list)
+    {
+        gpio_reset_pin((gpio_num_t)i);
+        gpio_set_direction((gpio_num_t)i, GPIO_MODE_INPUT);
+        gpio_set_pull_mode((gpio_num_t)i, GPIO_PULLUP_ONLY);
+    }
+
+    _set_output(output_list, 0);
+}
+
+uint8_t Keyboard_Class::getKey(Point2D_t keyCoor)
+{
+    uint8_t ret = 0;
+
+    if ((keyCoor.x < 0) || (keyCoor.y < 0))
+    {
+        return 0;
+    }
+    if (_keys_state_buffer.ctrl || _keys_state_buffer.shift ||
+        _is_caps_locked)
+    {
+        ret = _key_value_map[keyCoor.y][keyCoor.x].value_second;
+    }
+    else
+    {
+        ret = _key_value_map[keyCoor.y][keyCoor.x].value_first;
+    }
+    return ret;
+}
+
+void Keyboard_Class::updateKeyList()
+{
+    _key_list_buffer.clear();
+    Point2D_t coor;
+    uint8_t input_value = 0;
+
+    for (int i = 0; i < 8; i++)
+    {
+        _set_output(output_list, i);
+        input_value = _get_input(input_list);
+        /* If key pressed */
+
+        if (input_value)
+        {
+            /* Get X */
+            for (int j = 0; j < 7; j++)
+            {
+                if (input_value & (0x01 << j))
+                {
+                    coor.x = (i > 3) ? X_map_chart[j].x_1 : X_map_chart[j].x_2;
+
+                    /* Get Y */
+                    coor.y = (i > 3) ? (i - 4) : i;
+                    // printf("%d,%d\t", coor.x, coor.y);
+
+                    /* Keep the same as picture */
+                    coor.y = -coor.y;
+                    coor.y = coor.y + 3;
+
+                    _key_list_buffer.push_back(coor);
+                }
+            }
+        }
+    }
+}
+
+uint8_t Keyboard_Class::isPressed()
+{
+    return _key_list_buffer.size();
+}
+
+bool Keyboard_Class::isChange()
+{
+    if (_last_key_size != _key_list_buffer.size())
+    {
+        _last_key_size = _key_list_buffer.size();
+        return true;
+    }
+    else
+    {
+        return false;
+    }
+}
+
+String Keyboard_Class::getPressedKeysString() {
+    updateKeyList();
+    String pressed = "";
+
+    for (auto &keyCoor : _key_list_buffer) {
+        pressed += getKey(keyCoor);
+    }
+
+    return pressed;
+}
+
+bool Keyboard_Class::isKeyPressed(char c)
+{
+    if (_key_list_buffer.size())
+    {
+        for (const auto &i : _key_list_buffer)
+        {
+            if (getKey(i) == c)
+                return true;
+        }
+    }
+    return false;
+}
+
+#include <cstring>
+
+void Keyboard_Class::updateKeysState()
+{
+    _keys_state_buffer.reset();
+    _key_pos_print_keys.clear();
+    _key_pos_hid_keys.clear();
+    _key_pos_modifier_keys.clear();
+
+    // Get special keys
+    for (auto &i : _key_list_buffer)
+    {
+        // modifier
+        if (getKeyValue(i).value_first == KEY_FN)
+        {
+            _keys_state_buffer.fn = true;
+            continue;
+        }
+        if (getKeyValue(i).value_first == KEY_OPT)
+        {
+            _keys_state_buffer.opt = true;
+            continue;
+        }
+
+        if (getKeyValue(i).value_first == KEY_LEFT_CTRL)
+        {
+            _keys_state_buffer.ctrl = true;
+            _key_pos_modifier_keys.push_back(i);
+            continue;
+        }
+
+        if (getKeyValue(i).value_first == KEY_LEFT_SHIFT)
+        {
+            _keys_state_buffer.shift = true;
+            _key_pos_modifier_keys.push_back(i);
+            continue;
+        }
+
+        if (getKeyValue(i).value_first == KEY_LEFT_ALT)
+        {
+            _keys_state_buffer.alt = true;
+            _key_pos_modifier_keys.push_back(i);
+            continue;
+        }
+
+        // function
+        if (getKeyValue(i).value_first == KEY_TAB)
+        {
+            _keys_state_buffer.tab = true;
+            _key_pos_hid_keys.push_back(i);
+            continue;
+        }
+
+        if (getKeyValue(i).value_first == KEY_BACKSPACE)
+        {
+            _keys_state_buffer.del = true;
+            _key_pos_hid_keys.push_back(i);
+            continue;
+        }
+
+        if (getKeyValue(i).value_first == KEY_ENTER)
+        {
+            _keys_state_buffer.enter = true;
+            _key_pos_hid_keys.push_back(i);
+            continue;
+        }
+
+        if (getKeyValue(i).value_first == ' ')
+        {
+            _keys_state_buffer.space = true;
+        }
+        _key_pos_hid_keys.push_back(i);
+        _key_pos_print_keys.push_back(i);
+    }
+
+    for (auto &i : _key_pos_modifier_keys)
+    {
+        uint8_t key = getKeyValue(i).value_first;
+        _keys_state_buffer.modifier_keys.push_back(key);
+    }
+
+    for (auto &k : _keys_state_buffer.modifier_keys)
+    {
+        _keys_state_buffer.modifiers |= (1 << (k - 0x80));
+    }
+
+    for (auto &i : _key_pos_hid_keys)
+    {
+        uint8_t k = getKeyValue(i).value_first;
+        if (k == KEY_TAB || k == KEY_BACKSPACE || k == KEY_ENTER)
+        {
+            _keys_state_buffer.hid_keys.push_back(k);
+            continue;
+        }
+        uint8_t key = _kb_asciimap[k];
+        if (key)
+        {
+            _keys_state_buffer.hid_keys.push_back(key);
+        }
+    }
+
+    // Deal what left
+    for (auto &i : _key_pos_print_keys)
+    {
+        if (_keys_state_buffer.ctrl || _keys_state_buffer.shift ||
+            _is_caps_locked)
+        {
+            _keys_state_buffer.word.push_back(getKeyValue(i).value_second);
+        }
+        else
+        {
+            _keys_state_buffer.word.push_back(getKeyValue(i).value_first);
+        }
+    }
+}
+
+#endif
--- a/esp32_marauder/Keyboard.h
+++ b/esp32_marauder/Keyboard.h
@@ -0,0 +1,206 @@
+#pragma once
+
+#ifndef Keyboard_h
+#define Keyboard_h
+
+#include "configs.h"
+
+#ifdef MARAUDER_CARDPUTER
+
+/**
+ * @file keyboard.h
+ * @author Forairaaaaa
+ * @brief
+ * @version 0.1
+ * @date 2023-09-22
+ *
+ * @copyright Copyright (c) 2023
+ *
+ */
+#include <iostream>
+#include <vector>
+#include "Arduino.h"
+#include "Keyboard_def.h"
+#include "configs.h"
+
+struct Chart_t
+{
+    uint8_t value;
+    uint8_t x_1;
+    uint8_t x_2;
+};
+
+struct Point2D_t
+{
+    int x;
+    int y;
+};
+
+const std::vector<int> output_list = {8, 9, 11};
+const std::vector<int> input_list = {13, 15, 3, 4, 5, 6, 7};
+
+const Chart_t X_map_chart[7] = {{1, 0, 1}, {2, 2, 3}, {4, 4, 5}, {8, 6, 7}, {16, 8, 9}, {32, 10, 11}, {64, 12, 13}};
+
+struct KeyValue_t
+{
+    const char value_first;
+    const char value_second;
+};
+
+const KeyValue_t _key_value_map[4][14] = {{{'`', '~'},
+                                           {'1', '!'},
+                                           {'2', '@'},
+                                           {'3', '#'},
+                                           {'4', '$'},
+                                           {'5', '%'},
+                                           {'6', '^'},
+                                           {'7', '&'},
+                                           {'8', '*'},
+                                           {'9', '('},
+                                           {'0', ')'},
+                                           {'-', '_'},
+                                           {'=', '+'},
+                                           {KEY_BACKSPACE, KEY_BACKSPACE}},
+                                          {{KEY_TAB, KEY_TAB},
+                                           {'q', 'Q'},
+                                           {'w', 'W'},
+                                           {'e', 'E'},
+                                           {'r', 'R'},
+                                           {'t', 'T'},
+                                           {'y', 'Y'},
+                                           {'u', 'U'},
+                                           {'i', 'I'},
+                                           {'o', 'O'},
+                                           {'p', 'P'},
+                                           {'[', '{'},
+                                           {']', '}'},
+                                           {'\\', '|'}},
+                                          {{KEY_FN, KEY_FN},
+                                           {KEY_LEFT_SHIFT, KEY_LEFT_SHIFT},
+                                           {'a', 'A'},
+                                           {'s', 'S'},
+                                           {'d', 'D'},
+                                           {'f', 'F'},
+                                           {'g', 'G'},
+                                           {'h', 'H'},
+                                           {'j', 'J'},
+                                           {'k', 'K'},
+                                           {'l', 'L'},
+                                           {';', ':'},
+                                           {'\'', '\"'},
+                                           {KEY_ENTER, KEY_ENTER}},
+                                          {{KEY_LEFT_CTRL, KEY_LEFT_CTRL},
+                                           {KEY_OPT, KEY_OPT},
+                                           {KEY_LEFT_ALT, KEY_LEFT_ALT},
+                                           {'z', 'Z'},
+                                           {'x', 'X'},
+                                           {'c', 'C'},
+                                           {'v', 'V'},
+                                           {'b', 'B'},
+                                           {'n', 'N'},
+                                           {'m', 'M'},
+                                           {',', '<'},
+                                           {'.', '>'},
+                                           {'/', '?'},
+                                           {' ', ' '}}};
+
+class Keyboard_Class
+{
+public:
+    struct KeysState
+    {
+        bool tab = false;
+        bool fn = false;
+        bool shift = false;
+        bool ctrl = false;
+        bool opt = false;
+        bool alt = false;
+        bool del = false;
+        bool enter = false;
+        bool space = false;
+        uint8_t modifiers = 0;
+
+        std::vector<char> word;
+        std::vector<uint8_t> hid_keys;
+        std::vector<uint8_t> modifier_keys;
+
+        void reset()
+        {
+            tab = false;
+            fn = false;
+            shift = false;
+            ctrl = false;
+            opt = false;
+            alt = false;
+            del = false;
+            enter = false;
+            space = false;
+            modifiers = 0;
+            word.clear();
+            hid_keys.clear();
+            modifier_keys.clear();
+        }
+    };
+
+private:
+    std::vector<Point2D_t> _key_list_buffer;
+    std::vector<Point2D_t> _key_pos_print_keys; // only text: eg A,B,C
+    std::vector<Point2D_t> _key_pos_hid_keys;   // print key + space, enter, del
+    std::vector<Point2D_t>
+        _key_pos_modifier_keys; // modifier key: eg shift, ctrl, alt
+    KeysState _keys_state_buffer;
+    bool _is_caps_locked;
+    uint8_t _last_key_size;
+
+    void _set_output(const std::vector<int> &pinList, uint8_t output);
+    uint8_t _get_input(const std::vector<int> &pinList);
+
+public:
+    const char _ascii_list[95] = {'a','b','c','d','e','f','g','h','i','j','k','l','m','n','o','p',
+                            'q','r','s','t','u','v','w','x','y','z','A','B','C','D','E','F',
+                            'G','H','I','J','K','L','M','N','O','P','Q','R','S','T','U','V',
+                            'W','X','Y','Z',' ','0','1','2','3','4','5','6','7','8','9','-',
+                            '=','[',']',';','\'',',','.','/','`','\\','_','+','{','}',':',
+                            '"','<','>','?','~','|','!','@','#','$','%','^','&','*','(',')'};
+                            
+    Keyboard_Class() : _is_caps_locked(false)
+    {
+    }
+
+    void begin();
+    uint8_t getKey(Point2D_t keyCoor);
+
+    void updateKeyList();
+    inline std::vector<Point2D_t> &keyList()
+    {
+        return _key_list_buffer;
+    }
+
+    inline KeyValue_t getKeyValue(const Point2D_t &keyCoor)
+    {
+        return _key_value_map[keyCoor.y][keyCoor.x];
+    }
+
+    uint8_t isPressed();
+    bool isChange();
+    bool isKeyPressed(char c);
+    String getPressedKeysString();
+
+    void updateKeysState();
+    inline KeysState &keysState()
+    {
+        return _keys_state_buffer;
+    }
+
+    inline bool capslocked(void)
+    {
+        return _is_caps_locked;
+    }
+    inline void setCapsLocked(bool isLocked)
+    {
+        _is_caps_locked = isLocked;
+    }
+};
+#endif
+
+#endif
--- a/esp32_marauder/Keyboard_def.h
+++ b/esp32_marauder/Keyboard_def.h
@@ -0,0 +1,155 @@
+#ifndef M5CARDPUTER_KB_KEYS_DEF_H
+#define M5CARDPUTER_KB_KEYS_DEF_H
+
+#include "configs.h"
+
+#ifdef MARAUDER_CARDPUTER
+
+#define SHIFT 0x80
+
+#define KEY_LEFT_CTRL 0x80
+#define KEY_LEFT_SHIFT 0x81
+#define KEY_LEFT_ALT 0x82
+
+#define KEY_FN 0xff
+#define KEY_OPT 0x00
+
+#define KEY_BACKSPACE 0x2a
+#define KEY_TAB 0x2b
+#define KEY_ENTER 0x28
+
+const uint8_t _kb_asciimap[128] = {
+    0x00,          // NUL
+    0x00,          // SOH
+    0x00,          // STX
+    0x00,          // ETX
+    0x00,          // EOT
+    0x00,          // ENQ
+    0x00,          // ACK
+    0x00,          // BEL
+    KEY_BACKSPACE, // BS	Backspace
+    KEY_TAB,       // TAB	Tab
+    KEY_ENTER,     // LF	Enter
+    0x00,          // VT
+    0x00,          // FF
+    0x00,          // CR
+    0x00,          // SO
+    0x00,          // SI
+    0x00,          // DEL
+    0x00,          // DC1
+    0x00,          // DC2
+    0x00,          // DC3
+    0x00,          // DC4
+    0x00,          // NAK
+    0x00,          // SYN
+    0x00,          // ETB
+    0x00,          // CAN
+    0x00,          // EM
+    0x00,          // SUB
+    0x00,          // ESC
+    0x00,          // FS
+    0x00,          // GS
+    0x00,          // RS
+    0x00,          // US
+
+    0x2c,         //  ' '
+    0x1e | SHIFT, // !
+    0x34 | SHIFT, // "
+    0x20 | SHIFT, // #
+    0x21 | SHIFT, // $
+    0x22 | SHIFT, // %
+    0x24 | SHIFT, // &
+    0x34,         // '
+    0x26 | SHIFT, // (
+    0x27 | SHIFT, // )
+    0x25 | SHIFT, // *
+    0x2e | SHIFT, // +
+    0x36,         // ,
+    0x2d,         // -
+    0x37,         // .
+    0x38,         // /
+    0x27,         // 0
+    0x1e,         // 1
+    0x1f,         // 2
+    0x20,         // 3
+    0x21,         // 4
+    0x22,         // 5
+    0x23,         // 6
+    0x24,         // 7
+    0x25,         // 8
+    0x26,         // 9
+    0x33 | SHIFT, // :
+    0x33,         // ;
+    0x36 | SHIFT, // <
+    0x2e,         // =
+    0x37 | SHIFT, // >
+    0x38 | SHIFT, // ?
+    0x1f | SHIFT, // @
+    0x04 | SHIFT, // A
+    0x05 | SHIFT, // B
+    0x06 | SHIFT, // C
+    0x07 | SHIFT, // D
+    0x08 | SHIFT, // E
+    0x09 | SHIFT, // F
+    0x0a | SHIFT, // G
+    0x0b | SHIFT, // H
+    0x0c | SHIFT, // I
+    0x0d | SHIFT, // J
+    0x0e | SHIFT, // K
+    0x0f | SHIFT, // L
+    0x10 | SHIFT, // M
+    0x11 | SHIFT, // N
+    0x12 | SHIFT, // O
+    0x13 | SHIFT, // P
+    0x14 | SHIFT, // Q
+    0x15 | SHIFT, // R
+    0x16 | SHIFT, // S
+    0x17 | SHIFT, // T
+    0x18 | SHIFT, // U
+    0x19 | SHIFT, // V
+    0x1a | SHIFT, // W
+    0x1b | SHIFT, // X
+    0x1c | SHIFT, // Y
+    0x1d | SHIFT, // Z
+    0x2f,         // [
+    0x31,         // bslash
+    0x30,         // ]
+    0x23 | SHIFT, // ^
+    0x2d | SHIFT, // _
+    0x35,         // `
+    0x04,         // a
+    0x05,         // b
+    0x06,         // c
+    0x07,         // d
+    0x08,         // e
+    0x09,         // f
+    0x0a,         // g
+    0x0b,         // h
+    0x0c,         // i
+    0x0d,         // j
+    0x0e,         // k
+    0x0f,         // l
+    0x10,         // m
+    0x11,         // n
+    0x12,         // o
+    0x13,         // p
+    0x14,         // q
+    0x15,         // r
+    0x16,         // s
+    0x17,         // t
+    0x18,         // u
+    0x19,         // v
+    0x1a,         // w
+    0x1b,         // x
+    0x1c,         // y
+    0x1d,         // z
+    0x2f | SHIFT, // {
+    0x31 | SHIFT, // |
+    0x30 | SHIFT, // }
+    0x35 | SHIFT, // ~
+    0             // DEL
+};
+
+#endif
+
+#endif
--- a/esp32_marauder/LedInterface.cpp
+++ b/esp32_marauder/LedInterface.cpp
@@ -6,14 +6,17 @@ LedInterface::LedInterface() {

 void LedInterface::RunSetup() {
  //Serial.println("Setting neopixel to black...");
-  strip.setBrightness(0);
-  strip.begin();
-  strip.setPixelColor(0, strip.Color(0, 0, 0));
-  strip.show();
-  //delay(100);
-  strip.setBrightness(50);
-  strip.setPixelColor(0, strip.Color(0, 0, 0));
-  strip.show();
+  #ifdef HAS_NEOPIXEL_LED
+    strip.setBrightness(0);
+    strip.begin();
+    strip.setPixelColor(0, strip.Color(0, 0, 0));
+    strip.show();
+    //delay(100);
+    strip.setBrightness(50);
+    strip.setPixelColor(0, strip.Color(0, 0, 0));
+    strip.show();
+  #endif
+
  this->initTime = millis();
 }

@@ -50,8 +53,10 @@ uint8_t LedInterface::getMode() {
 }

 void LedInterface::setColor(int r, int g, int b) {
-  strip.setPixelColor(0, strip.Color(r, g, b));
-  strip.show();  
+  #ifdef HAS_NEOPIXEL_LED
+    strip.setPixelColor(0, strip.Color(r, g, b));
+    strip.show();
+  #endif
 }

 void LedInterface::sniffLed() {
@@ -67,25 +72,29 @@ void LedInterface::ledOff() {
 }

 void LedInterface::rainbow() {
-  strip.setPixelColor(0, this->Wheel((0 * 256 / 100 + this->wheel_pos) % 256));
-  strip.show();
+  #ifdef HAS_NEOPIXEL_LED
+    strip.setPixelColor(0, this->Wheel((0 * 256 / 100 + this->wheel_pos) % 256));
+    strip.show();

-  this->current_fade_itter++;
+    this->current_fade_itter++;

-  this->wheel_pos = this->wheel_pos - this->wheel_speed;
-  if (this->wheel_pos < 0)
-    this->wheel_pos = 255;
+    this->wheel_pos = this->wheel_pos - this->wheel_speed;
+    if (this->wheel_pos < 0)
+      this->wheel_pos = 255;
+  #endif
 }

 uint32_t LedInterface::Wheel(byte WheelPos) {
-  WheelPos = 255 - WheelPos;
-  if(WheelPos < 85) {
-    return strip.Color(255 - WheelPos * 3, 0, WheelPos * 3);
-  }
-  if(WheelPos < 170) {
-    WheelPos -= 85;
-    return strip.Color(0, WheelPos * 3, 255 - WheelPos * 3);
-  }
-  WheelPos -= 170;
-  return strip.Color(WheelPos * 3, 255 - WheelPos * 3, 0);
+  #ifdef HAS_NEOPIXEL_LED
+    WheelPos = 255 - WheelPos;
+    if(WheelPos < 85) {
+      return strip.Color(255 - WheelPos * 3, 0, WheelPos * 3);
+    }
+    if(WheelPos < 170) {
+      WheelPos -= 85;
+      return strip.Color(0, WheelPos * 3, 255 - WheelPos * 3);
+    }
+    WheelPos -= 170;
+    return strip.Color(WheelPos * 3, 255 - WheelPos * 3, 0);
+  #endif
 }
--- a/esp32_marauder/MenuFunctions.cpp
+++ b/esp32_marauder/MenuFunctions.cpp
--- a/esp32_marauder/MenuFunctions.h
+++ b/esp32_marauder/MenuFunctions.h
@@ -5,6 +5,10 @@

 #include "configs.h"

+#ifdef MARAUDER_CARDPUTER
+  #include "Keyboard.h"
+#endif
+
 #ifdef HAS_SCREEN

 #define BATTERY_ANALOG_ON 0
@@ -16,11 +20,21 @@

 #ifdef HAS_BUTTONS
  #include "Switches.h"
-  extern Switches u_btn;
-  extern Switches d_btn;
-  extern Switches l_btn;
-  extern Switches r_btn;
-  extern Switches c_btn;
+  #if (U_BTN >= 0)
+    extern Switches u_btn;
+  #endif
+  #if (D_BTN >= 0)
+    extern Switches d_btn;
+  #endif
+  #if (L_BTN >= 0)
+    extern Switches l_btn;
+  #endif
+  #if (R_BTN >= 0)
+    extern Switches r_btn;
+  #endif
+  #if (C_BTN >= 0)
+    extern Switches c_btn;
+  #endif
 #endif

 extern WiFiScan wifi_scan_obj;
@@ -74,6 +88,10 @@ extern Settings settings_obj;
 #define DISABLE_TOUCH 34
 #define FLIPPER 35
 #define BLANK 36
+#define PINESCAN_SNIFF 37 // Use blanks icon
+#define MULTISSID_SNIFF 37 // Use blanks icon
+#define JOINED 38
+#define FORCE 39

 PROGMEM void my_disp_flush(lv_disp_drv_t *disp, const lv_area_t *area, lv_color_t *color_p);
 PROGMEM bool my_touchpad_read(lv_indev_drv_t * indev_driver, lv_indev_data_t * data);
@@ -82,9 +100,11 @@ PROGMEM static lv_disp_buf_t disp_buf;
 PROGMEM static lv_color_t buf[LV_HOR_RES_MAX * 10];

 PROGMEM static void ta_event_cb(lv_obj_t * ta, lv_event_t event);
+PROGMEM static void join_wifi_keyboard_event_cb(lv_obj_t * keyboard, lv_event_t event);
 PROGMEM static void add_ssid_keyboard_event_cb(lv_obj_t * keyboard, lv_event_t event);
 PROGMEM static void html_list_cb(lv_obj_t * btn, lv_event_t event);
 PROGMEM static void ap_list_cb(lv_obj_t * btn, lv_event_t event);
+PROGMEM static void ap_info_list_cb(lv_obj_t * btn, lv_event_t event);
 PROGMEM static void at_list_cb(lv_obj_t * btn, lv_event_t event);
 PROGMEM static void station_list_cb(lv_obj_t * btn, lv_event_t event);
 PROGMEM static void setting_dropdown_cb(lv_obj_t * btn, lv_event_t event);
@@ -155,29 +175,34 @@ class MenuFunctions
    Menu updateMenu;
    Menu settingsMenu;
    Menu specSettingMenu;
-    Menu infoMenu;
    Menu languageMenu;
    Menu sdDeleteMenu;

    // WiFi menu stuff
    Menu wifiSnifferMenu;
+    Menu wifiScannerMenu;
    Menu wifiAttackMenu;
    #ifdef HAS_GPS
      Menu wardrivingMenu;
    #endif
    Menu wifiGeneralMenu;
    Menu wifiAPMenu;
+    Menu wifiIPMenu;
    #ifdef HAS_BT
      Menu airtagMenu;
    #endif
-    #ifndef HAS_ILI9341
+    //#ifndef HAS_ILI9341
      Menu wifiStationMenu;
-    #endif
+    //#endif

    // WiFi General Menu
    Menu htmlMenu;
    Menu miniKbMenu;
    Menu saveFileMenu;
+    Menu genAPMacMenu;
+    Menu cloneAPMacMenu;
+    Menu setMacMenu;
+    Menu selectProbeSSIDsMenu;

    // Bluetooth menu stuff
    Menu bluetoothSnifferMenu;
@@ -190,7 +215,7 @@ class MenuFunctions

    // Menu icons

-
+    void displayMenuButtons();
    uint16_t getColor(uint16_t color);
    void drawAvgLine(int16_t value);
    void drawMaxLine(int16_t value, uint16_t color);
@@ -208,11 +233,14 @@ class MenuFunctions
    void displaySetting(String key, Menu* menu, int index);
    void buttonSelected(int b, int x = -1);
    void buttonNotSelected(int b, int x = -1);
-    #if (!defined(HAS_ILI9341) && defined(HAS_BUTTONS))
-      void miniKeyboard(Menu * targetMenu);
-    #endif
+    //#if (!defined(HAS_ILI9341) && defined(HAS_BUTTONS))
+      String miniKeyboard(Menu * targetMenu, bool do_pass = false);
+    //#endif

-    uint8_t updateTouch(uint16_t *x, uint16_t *y, uint16_t threshold = 600);
+    #ifdef MARAUDER_CARDPUTER
+      Keyboard_Class M5CardputerKeyboard = Keyboard_Class();
+      bool isKeyPressed(char c);
+    #endif

  public:
    MenuFunctions();
@@ -234,6 +262,9 @@ class MenuFunctions
      Menu gpsInfoMenu;
    #endif

+    Menu infoMenu;
+    Menu apInfoMenu;
+
    Ticker tick;

    uint16_t x = -1, y = -1;
@@ -243,6 +274,7 @@ class MenuFunctions

    String loaded_file = "";

+    void joinWiFiGFX(String essid);
    void setGraphScale(float scale);
    void initLVGL();
    void deinitLVGL();
--- a/esp32_marauder/SDInterface.cpp
+++ b/esp32_marauder/SDInterface.cpp
@@ -1,6 +1,10 @@
 #include "SDInterface.h"
 #include "lang_var.h"

+#ifdef HAS_C5_SD
+  SDInterface::SDInterface(SPIClass* spi, int cs)
+    : _spi(spi), _cs(cs) {}
+#endif

 bool SDInterface::initSD() {
  #ifdef HAS_SD
@@ -21,7 +25,7 @@ bool SDInterface::initSD() {
    pinMode(SD_CS, OUTPUT);

    delay(10);
-    #if defined(MARAUDER_M5STICKC)
+    #if (defined(MARAUDER_M5STICKC)) || (defined(HAS_CYD_TOUCH)) || (defined(MARAUDER_CARDPUTER))
      /* Set up SPI SD Card using external pin header
      StickCPlus Header - SPI SD Card Reader
                  3v3   -   3v3
@@ -31,10 +35,24 @@ bool SDInterface::initSD() {
                  G26   -   MOSI
                        -   CS (jumper to SD Card GND Pin)
      */
-      enum { SPI_SCK = 0, SPI_MISO = 36, SPI_MOSI = 26 };
-      this->spiExt = new SPIClass();
+      #if defined(MARAUDER_M5STICKC)
+        enum { SPI_SCK = 0, SPI_MISO = 36, SPI_MOSI = 26 };
+      #elif defined(HAS_CYD_TOUCH) || defined(MARAUDER_CARDPUTER)
+        enum { SPI_SCK = SD_SCK, SPI_MISO = SD_MISO, SPI_MOSI = SD_MOSI };
+      #else
+        enum { SPI_SCK = 0, SPI_MISO = 36, SPI_MOSI = 26 };
+      #endif
+      #ifndef MARAUDER_CARDPUTER
+        this->spiExt = new SPIClass();
+      #else
+        this->spiExt = new SPIClass(FSPI);
+      #endif
+      Serial.println("Using external SPI configuration...");
      this->spiExt->begin(SPI_SCK, SPI_MISO, SPI_MOSI, SD_CS);
      if (!SD.begin(SD_CS, *(this->spiExt))) {
+    #elif defined(HAS_C5_SD)
+      Serial.println("Using C5 SD configuration...");
+      if (!SD.begin(SD_CS, *_spi)) {
    #else
      if (!SD.begin(SD_CS)) {
    #endif
@@ -45,19 +63,9 @@ bool SDInterface::initSD() {
    else {
      this->supported = true;
      this->cardType = SD.cardType();
-      //if (cardType == CARD_MMC)
-      //  Serial.println(F("SD: MMC Mounted"));
-      //else if(cardType == CARD_SD)
-      //    Serial.println(F("SD: SDSC Mounted"));
-      //else if(cardType == CARD_SDHC)
-      //    Serial.println(F("SD: SDHC Mounted"));
-      //else
-      //    Serial.println(F("SD: UNKNOWN Card Mounted"));

      this->cardSizeMB = SD.cardSize() / (1024 * 1024);
    
-      //Serial.printf("SD Card Size: %lluMB\n", this->cardSizeMB);
-
      if (this->supported) {
        const int NUM_DIGITS = log10(this->cardSizeMB) + 1;

--- a/esp32_marauder/SDInterface.h
+++ b/esp32_marauder/SDInterface.h
@@ -6,7 +6,13 @@
 #include "configs.h"

 #include "settings.h"
+#ifdef HAS_C5_SD
+  #include "FS.h"
+#endif
 #include "SD.h"
+#ifdef HAS_C5_SD
+  #include "SPI.h"
+#endif
 #include "Buffer.h"
 #ifdef HAS_SCREEN
  #include "Display.h"
@@ -26,12 +32,19 @@ extern Settings settings_obj;
 class SDInterface {

  private:
-#if defined(MARAUDER_M5STICKC)
-  SPIClass *spiExt;
-#endif
+  #if (defined(MARAUDER_M5STICKC) || defined(HAS_CYD_TOUCH) || defined(MARAUDER_CARDPUTER))
+    SPIClass *spiExt;
+  #elif defined(HAS_C5_SD)
+    SPIClass* _spi;
+    int _cs;
+  #endif
    bool checkDetectPin();

  public:
+    #ifdef HAS_C5_SD
+      SDInterface(SPIClass* spi, int cs);
+    #endif
+
    uint8_t cardType;
    //uint64_t cardSizeBT;
    //uint64_t cardSizeKB;
--- a/esp32_marauder/WiFiScan.cpp
+++ b/esp32_marauder/WiFiScan.cpp
--- a/esp32_marauder/WiFiScan.h
+++ b/esp32_marauder/WiFiScan.h
@@ -11,14 +11,18 @@
 #include <vector>

 #ifdef HAS_BT
-  #include <NimBLEDevice.h>
+  #include <NimBLEDevice.h> // 1.3.8
 #endif

 #include <WiFi.h>
+#include <ESP32Ping.h>
 #include "EvilPortal.h"
 #include <math.h>
 #include "esp_wifi.h"
 #include "esp_wifi_types.h"
+#ifdef HAS_DUAL_BAND
+  #include "esp_system.h"
+#endif
 #ifdef HAS_BT
  #include "esp_bt.h"
 #endif
@@ -37,7 +41,7 @@
 #endif
 #include "settings.h"
 #include "Assets.h"
-#ifdef MARAUDER_FLIPPER
+#ifdef HAS_FLIPPER_LED
  #include "flipperLED.h"
 #elif defined(XIAO_ESP32_S3)
  #include "xiaoLED.h"
@@ -100,11 +104,54 @@
 #define BT_SCAN_FLIPPER 45
 #define WIFI_SCAN_CHAN_ANALYZER 46
 #define BT_SCAN_ANALYZER 47
+#define WIFI_SCAN_PACKET_RATE 48
+#define WIFI_SCAN_AP_STA 49
+#define WIFI_SCAN_PINESCAN 50
+#define WIFI_SCAN_MULTISSID 51
+#define WIFI_CONNECTED 52
+#define WIFI_PING_SCAN 53
+#define WIFI_PORT_SCAN_ALL 54

 #define BASE_MULTIPLIER 4

+#define ANALYZER_NAME_REFRESH 100 // Number of events to refresh the name
+
+// PineScan and Multi SSID
+#define MULTISSID_THRESHOLD 3 // Threshold For Multi SSID
+#define MAX_MULTISSID_ENTRIES 100 // Max number of confirmed MultiSSIDs to store
+#define MAX_AP_ENTRIES 100 // Max number of APs to track for analysis
+#define MAX_DISPLAY_ENTRIES 1 // Max Unique MACs to display
+#define MAX_PINESCAN_ENTRIES 100 // PineScan Max Entries
+
 #define MAX_CHANNEL     14

+#define MAX_PORT 65535
+
+#define WIFI_SECURITY_OPEN   0
+#define WIFI_SECURITY_WEP    1
+#define WIFI_SECURITY_WPA    2
+#define WIFI_SECURITY_WPA2   3
+#define WIFI_SECURITY_WPA3   4
+#define WIFI_SECURITY_WPA_WPA2_MIXED 5
+#define WIFI_SECURITY_WPA2_ENTERPRISE 6
+#define WIFI_SECURITY_WPA3_ENTERPRISE 7
+#define WIFI_SECURITY_WAPI 8
+#define WIFI_SECURITY_UNKNOWN 255
+
+#define WPS_CONFIG_USBA              0x0001
+#define WPS_CONFIG_ETHERNET          0x0002
+#define WPS_CONFIG_LABEL             0x0004
+#define WPS_CONFIG_DISPLAY           0x0008
+#define WPS_CONFIG_EXT_NFC_TOKEN     0x0010
+#define WPS_CONFIG_INT_NFC_TOKEN     0x0020
+#define WPS_CONFIG_NFC_INTERFACE     0x0040
+#define WPS_CONFIG_PUSH_BUTTON       0x0080
+#define WPS_CONFIG_KEYPAD            0x0100
+#define WPS_CONFIG_VIRT_PUSH_BUTTON  0x1000
+#define WPS_CONFIG_PHY_PUSH_BUTTON   0x2000
+#define WPS_CONFIG_VIRT_DISPLAY      0x4000
+#define WPS_CONFIG_PHY_DISPLAY       0x8000
+
 extern EvilPortal evil_portal_obj;

 #ifdef HAS_SCREEN
@@ -121,7 +168,7 @@ extern Buffer buffer_obj;
  extern BatteryInterface battery_obj;
 #endif
 extern Settings settings_obj;
-#ifdef MARAUDER_FLIPPER
+#ifdef HAS_FLIPPER_LED
  extern flipperLED flipper_led;
 #elif defined(XIAO_ESP32_S3)
  extern xiaoLED xiao_led;
@@ -133,6 +180,10 @@ extern Settings settings_obj;

 esp_err_t esp_wifi_80211_tx(wifi_interface_t ifx, const void *buffer, int len, bool en_sys_seq);

+#ifdef HAS_DUAL_BAND
+  esp_err_t esp_base_mac_addr_set(uint8_t *Mac);
+#endif
+
 /*struct ssid {
  String essid;
  uint8_t channel;
@@ -172,18 +223,28 @@ struct Flipper {
  String name;
 };

+#ifdef HAS_PSRAM
+  extern struct mac_addr* mac_history;
+#endif
+
 class WiFiScan
 {
  private:
    // Wardriver thanks to https://github.com/JosephHewitt
-    struct mac_addr mac_history[mac_history_len];
+    #ifndef HAS_PSRAM
+      struct mac_addr mac_history[mac_history_len];
+    #endif
+
+    uint8_t ap_mac[6] = {0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED};
+    uint8_t sta_mac[6] = {0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED};
+
+    uint8_t dual_band_channels[DUAL_BAND_CHANNELS] = {1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 32, 36, 40, 44, 48, 52, 56, 60, 64, 68, 72, 76, 80, 84, 88, 92, 96, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 144, 149, 153, 157, 161, 165, 169, 173, 177};
+
+    uint8_t dual_band_channel_index = 0;

    // Settings
    uint mac_history_cursor = 0;
    uint8_t channel_hop_delay = 1;
-    bool force_pmkid = false;
-    bool force_probe = false;
-    bool save_pcap = false;
  
    int x_pos; //position along the graph x axis
    float y_pos_x; //current graph y axis position of X value
@@ -200,6 +261,8 @@ class WiFiScan

    bool wsl_bypass_enabled = false;

+    bool scan_complete = false;
+
    //int num_beacon = 0; // GREEN
    //int num_probe = 0; // BLUE
    //int num_deauth = 0; // RED
@@ -246,6 +309,74 @@ class WiFiScan
      WifiMgmtHdr hdr;
    } wifi_ieee80211_packet_t;

+		// Tracking structures for PineScan (similar to MultiSSID)
+    struct PineScanTracker {
+        uint8_t mac[6];
+        bool suspicious_oui;
+        bool tag_and_susp_cap;
+        uint8_t channel;
+        int8_t rssi;
+        bool reported;
+    };
+
+    // For confirmed Pineapple devices
+    struct ConfirmedPineScan {
+        uint8_t mac[6];
+        String detection_type;
+        String essid;
+        uint8_t channel;
+        int8_t rssi;
+        bool displayed;
+    };
+    LinkedList<PineScanTracker>* pinescan_trackers;
+    LinkedList<ConfirmedPineScan>* confirmed_pinescan;
+    bool pinescan_list_full_reported;
+    
+    // Security Conditions For Pineapple detection
+    enum SecurityCondition {
+        NONE = 0x00,
+        SUSPICIOUS_WHEN_OPEN = 0x01,
+        SUSPICIOUS_WHEN_PROTECTED = 0x02,
+        SUSPICIOUS_ALWAYS = 0x04
+    };
+
+    // SuspiciousVendor struct
+    struct SuspiciousVendor {
+        const char* vendor_name;
+        uint8_t security_flags;
+        uint32_t ouis[20];                 // Array of OUIs (max 20 per vendor)
+        uint8_t oui_count;                 // Number of OUIs for this vendor
+    };
+
+    // Declare the table for Pineapple
+    static const SuspiciousVendor suspicious_vendors[];
+    static const int NUM_SUSPICIOUS_VENDORS;
+
+    // Track for AP list limit (Uninitialised, Done in RunSetup)
+    bool ap_list_full_reported;
+
+    // MULTI SSID STRUCTS
+
+    struct MultiSSIDTracker {
+        uint8_t mac[6];
+        uint16_t ssid_hashes[MULTISSID_THRESHOLD];
+        uint8_t unique_ssid_count;
+        bool reported;
+    };
+
+    // New struct for confirmed MultiSSID devices
+    struct ConfirmedMultiSSID {
+        uint8_t mac[6];
+        String essid;
+        uint8_t channel;
+        int8_t rssi;
+        uint8_t ssid_count;
+        bool displayed;
+    };
+    LinkedList<MultiSSIDTracker>* multissid_trackers;
+    LinkedList<ConfirmedMultiSSID>* confirmed_multissid;
+    bool multissid_list_full_reported;
+
    // barebones packet
    uint8_t packet[128] = { 0x80, 0x00, 0x00, 0x00, //Frame Control, Duration
                    /*4*/   0xff, 0xff, 0xff, 0xff, 0xff, 0xff, //Destination address 
@@ -307,6 +438,14 @@ class WiFiScan
      NimBLEAdvertisementData GetUniversalAdvertisementData(EBLEPayloadType type);
    #endif

+    void pingScan();
+    void portScan(uint8_t scan_mode = WIFI_PORT_SCAN_ALL);
+    bool isHostAlive(IPAddress ip);
+    bool checkHostPort(IPAddress ip, uint16_t port, uint16_t timeout = 100);
+    String extractManufacturer(const uint8_t* payload);
+    int checkMatchAP(char addr[]);
+    bool beaconHasWPS(const uint8_t* payload, int len);
+    uint8_t getSecurityType(const uint8_t* beacon, uint16_t len);
    void addAnalyzerValue(int16_t value, int rssi_avg, int16_t target_array[], int array_size);
    bool seen_mac(unsigned char* mac);
    bool mac_cmp(struct mac_addr addr1, struct mac_addr addr2);
@@ -323,7 +462,9 @@ class WiFiScan

    void startWiFiAttacks(uint8_t scan_mode, uint16_t color, String title_string);

+    void signalAnalyzerLoop(uint32_t tick);
    void channelAnalyzerLoop(uint32_t tick);
+    void packetRateLoop(uint32_t tick);
    void packetMonitorMain(uint32_t currentTime);
    void eapolMonitorMain(uint32_t currentTime);
    void updateMidway();
@@ -345,6 +486,8 @@ class WiFiScan
    void RunGPSNmea();
    void RunMimicFlood(uint8_t scan_mode, uint16_t color);
    void RunPwnScan(uint8_t scan_mode, uint16_t color);
+    void RunPineScan(uint8_t scan_mode, uint16_t color);
+    void RunMultiSSIDScan(uint8_t scan_mode, uint16_t color);
    void RunBeaconScan(uint8_t scan_mode, uint16_t color);
    void RunRawScan(uint8_t scan_mode, uint16_t color);
    void RunStationScan(uint8_t scan_mode, uint16_t color);
@@ -357,6 +500,8 @@ class WiFiScan
    void RunSwiftpairSpam(uint8_t scan_mode, uint16_t color);
    void RunLvJoinWiFi(uint8_t scan_mode, uint16_t color);
    void RunEvilPortal(uint8_t scan_mode, uint16_t color);
+    void RunPingScan(uint8_t scan_mode, uint16_t color);
+    void RunPortScanAll(uint8_t scan_mode, uint16_t color);
    bool checkMem();
    void parseBSSID(const char* bssidStr, uint8_t* bssid);

@@ -368,6 +513,27 @@ class WiFiScan

    //LinkedList<ssid>* ssids;

+    // Stuff for RAW stats
+    uint32_t mgmt_frames = 0;
+    uint32_t data_frames = 0;
+    uint32_t beacon_frames = 0;
+    uint32_t req_frames = 0;
+    uint32_t resp_frames = 0;
+    uint32_t deauth_frames = 0;
+    uint32_t eapol_frames = 0;
+    int8_t min_rssi = 0;
+    int8_t max_rssi = -128;
+
+    bool force_pmkid = false;
+    bool force_probe = false;
+    bool save_pcap = false;
+
+    String analyzer_name_string = "";
+    
+    uint8_t analyzer_frames_recvd = 0;
+
+    bool analyzer_name_update = false;
+
    uint8_t set_channel = 1;

    uint8_t old_channel = 0;
@@ -377,11 +543,20 @@ class WiFiScan
    bool orient_display = false;
    bool wifi_initialized = false;
    bool ble_initialized = false;
+    bool wifi_connected = false;

    String free_ram = "";
    String old_free_ram = "";
    String connected_network = "";

+    IPAddress ip_addr;
+    IPAddress gateway;
+    IPAddress subnet;
+
+    IPAddress current_scan_ip;
+
+    uint16_t current_scan_port = 1;
+
    String dst_mac = "ff:ff:ff:ff:ff:ff";
    byte src_mac[6] = {};

@@ -396,55 +571,72 @@ class WiFiScan

    wifi_init_config_t cfg = WIFI_INIT_CONFIG_DEFAULT();

-    wifi_init_config_t cfg2 = { \
-        .event_handler = &esp_event_send_internal, \
-        .osi_funcs = &g_wifi_osi_funcs, \
-        .wpa_crypto_funcs = g_wifi_default_wpa_crypto_funcs, \
-        .static_rx_buf_num = 6,\
-        .dynamic_rx_buf_num = 6,\
-        .tx_buf_type = 0,\
-        .static_tx_buf_num = 1,\
-        .dynamic_tx_buf_num = WIFI_DYNAMIC_TX_BUFFER_NUM,\
-        .cache_tx_buf_num = 0,\
-        .csi_enable = false,\
-        .ampdu_rx_enable = false,\
-        .ampdu_tx_enable = false,\
-        .amsdu_tx_enable = false,\
-        .nvs_enable = false,\
-        .nano_enable = WIFI_NANO_FORMAT_ENABLED,\
-        .rx_ba_win = 6,\
-        .wifi_task_core_id = WIFI_TASK_CORE_ID,\
-        .beacon_max_len = 752, \
-        .mgmt_sbuf_num = 8, \
-        .feature_caps = g_wifi_feature_caps, \
-        .sta_disconnected_pm = WIFI_STA_DISCONNECTED_PM_ENABLED,  \
-        .espnow_max_encrypt_num = 0, \
-        .magic = WIFI_INIT_CONFIG_MAGIC\
-    };
+    #ifndef HAS_DUAL_BAND
+      wifi_init_config_t cfg2 = { \
+          .event_handler = &esp_event_send_internal, \
+          .osi_funcs = &g_wifi_osi_funcs, \
+          .wpa_crypto_funcs = g_wifi_default_wpa_crypto_funcs, \
+          .static_rx_buf_num = 6,\
+          .dynamic_rx_buf_num = 6,\
+          .tx_buf_type = 0,\
+          .static_tx_buf_num = 1,\
+          .dynamic_tx_buf_num = WIFI_DYNAMIC_TX_BUFFER_NUM,\
+          .cache_tx_buf_num = 0,\
+          .csi_enable = false,\
+          .ampdu_rx_enable = false,\
+          .ampdu_tx_enable = false,\
+          .amsdu_tx_enable = false,\
+          .nvs_enable = false,\
+          .nano_enable = WIFI_NANO_FORMAT_ENABLED,\
+          .rx_ba_win = 6,\
+          .wifi_task_core_id = WIFI_TASK_CORE_ID,\
+          .beacon_max_len = 752, \
+          .mgmt_sbuf_num = 8, \
+          .feature_caps = g_wifi_feature_caps, \
+          .sta_disconnected_pm = WIFI_STA_DISCONNECTED_PM_ENABLED,  \
+          .espnow_max_encrypt_num = 0, \
+          .magic = WIFI_INIT_CONFIG_MAGIC\
+      };
+    #else
+      wifi_init_config_t cfg2 = WIFI_INIT_CONFIG_DEFAULT();
+    #endif

    wifi_config_t ap_config;

+    #ifdef HAS_SCREEN
+      int8_t checkAnalyzerButtons(uint32_t currentTime);
+    #endif
+    void setMac();
+    void renderRawStats();
+    void renderPacketRate();
+    void displayAnalyzerString(String str);
    String security_int_to_string(int security_type);
    char* stringToChar(String string);
    void RunSetup();
    int clearSSIDs();
    int clearAPs();
+    int clearIPs();
    int clearAirtags();
    int clearFlippers();
    int clearStations();
+    int clearPineScanTrackers();
+    int clearMultiSSID();
    bool addSSID(String essid);
    int generateSSIDs(int count = 20);
    bool shutdownWiFi();
    bool shutdownBLE();
    bool scanning();
-    //void joinWiFi(String ssid, String password);
+    bool joinWiFi(String ssid, String password, bool gui = true);
    String getStaMAC();
    String getApMAC();
    String freeRAM();
    void changeChannel();
    void changeChannel(int chan);
+    void RunAPInfo(uint16_t index, bool do_display = true);
    void RunInfo();
    //void RunShutdownBLE();
+    void RunSetMac(uint8_t * mac, bool ap = true);
+    void RunGenerateRandomMac(bool ap = true);
    void RunGenerateSSIDs(int count = 20);
    void RunClearSSIDs();
    void RunClearAPs();
@@ -481,6 +673,9 @@ class WiFiScan
    static void activeEapolSnifferCallback(void* buf, wifi_promiscuous_pkt_type_t type);
    static void eapolSnifferCallback(void* buf, wifi_promiscuous_pkt_type_t type);
    static void wifiSnifferCallback(void* buf, wifi_promiscuous_pkt_type_t type);
+    static void pineScanSnifferCallback(void* buf, wifi_promiscuous_pkt_type_t type); // Pineapple
+    static int extractPineScanChannel(const uint8_t* payload, int len); // Pineapple
+    static void multiSSIDSnifferCallback(void* buf, wifi_promiscuous_pkt_type_t type); // MultiSSID

    /*#ifdef HAS_BT
      enum EBLEPayloadType
--- a/esp32_marauder/configs.h
+++ b/esp32_marauder/configs.h
--- a/esp32_marauder/esp32_marauder.ino
+++ b/esp32_marauder/esp32_marauder.ino
@@ -34,7 +34,7 @@ https://www.online-utility.org/image/convert/to/XBM
 #endif
 #include "Buffer.h"

-#ifdef MARAUDER_FLIPPER
+#ifdef HAS_FLIPPER_LED
  #include "flipperLED.h"
 #elif defined(XIAO_ESP32_S3)
  #include "xiaoLED.h"
@@ -97,7 +97,7 @@ CommandLine cli_obj;
  MenuFunctions menu_function_obj;
 #endif

-#ifdef HAS_SD
+#if defined(HAS_SD) && !defined(HAS_C5_SD)
  SDInterface sd_obj;
 #endif

@@ -105,7 +105,7 @@ CommandLine cli_obj;
  AXP192 axp192_obj;
 #endif

-#ifdef MARAUDER_FLIPPER
+#ifdef HAS_FLIPPER_LED
  flipperLED flipper_led;
 #elif defined(XIAO_ESP32_S3)
  xiaoLED xiao_led;
@@ -123,7 +123,6 @@ const String PROGMEM version_number = MARAUDER_VERSION;

 uint32_t currentTime  = 0;

-
 void backlightOn() {
  #ifdef HAS_SCREEN
    #ifdef MARAUDER_MINI
@@ -148,9 +147,23 @@ void backlightOff() {
  #endif
 }

+#ifdef HAS_C5_SD
+  SPIClass sharedSPI(SPI);
+  SDInterface sd_obj = SDInterface(&sharedSPI, SD_CS);
+#endif

 void setup()
 {
+  #ifndef HAS_DUAL_BAND
+    esp_spiram_init();
+  #endif
+
+  #ifdef HAS_C5_SD
+    Serial.println("Starting shared SPI for C5 SD configuration...");
+    sharedSPI.begin(SD_SCK, SD_MISO, SD_MOSI);
+    delay(100);
+  #endif
+
  #ifdef defined(MARAUDER_M5STICKC) && !defined(MARAUDER_M5STICKCP2)
    axp192_obj.begin();
  #endif
@@ -165,17 +178,17 @@ void setup()
  #endif
  
  backlightOff();
-#if BATTERY_ANALOG_ON == 1
-  pinMode(BATTERY_PIN, OUTPUT);
-  pinMode(CHARGING_PIN, INPUT);
-#endif
+  #if BATTERY_ANALOG_ON == 1
+    pinMode(BATTERY_PIN, OUTPUT);
+    pinMode(CHARGING_PIN, INPUT);
+  #endif
  
  // Preset SPI CS pins to avoid bus conflicts
  #ifdef HAS_SCREEN
    digitalWrite(TFT_CS, HIGH);
  #endif
  
-  #ifdef HAS_SD
+  #if defined(HAS_SD) && !defined(HAS_C5_SD)
    pinMode(SD_CS, OUTPUT);

    delay(10);
@@ -192,6 +205,14 @@ void setup()

  Serial.println("ESP-IDF version is: " + String(esp_get_idf_version()));

+  #ifdef HAS_PSRAM
+    if (psramInit()) {
+      Serial.println("PSRAM is correctly initialized");
+    } else {
+      Serial.println("PSRAM not available");
+    }
+  #endif
+
  #ifdef HAS_SCREEN
    display_obj.RunSetup();
    display_obj.tft.setTextColor(TFT_WHITE, TFT_BLACK);
@@ -199,22 +220,17 @@ void setup()

  backlightOff();

-  // Draw the title screen
-  /*
  #ifdef HAS_SCREEN
-    #ifndef MARAUDER_MINI
-      display_obj.drawJpeg("/marauder3L.jpg", 0 , 0);     // 240 x 320 image
+    #ifndef MARAUDER_CARDPUTER
+      display_obj.tft.drawCentreString("ESP32 Marauder", TFT_WIDTH/2, TFT_HEIGHT * 0.33, 1);
+      display_obj.tft.drawCentreString("JustCallMeKoko", TFT_WIDTH/2, TFT_HEIGHT * 0.5, 1);
+      display_obj.tft.drawCentreString(display_obj.version_number, TFT_WIDTH/2, TFT_HEIGHT * 0.66, 1);
    #else
-      display_obj.drawJpeg("/marauder3L.jpg", 0, 0);
+      display_obj.tft.drawCentreString("ESP32 Marauder", TFT_HEIGHT/2, TFT_WIDTH * 0.33, 1);
+      display_obj.tft.drawCentreString("JustCallMeKoko", TFT_HEIGHT/2, TFT_WIDTH * 0.5, 1);
+      display_obj.tft.drawCentreString(display_obj.version_number, TFT_HEIGHT/2, TFT_WIDTH * 0.66, 1);
    #endif
  #endif
-  */
-
-  #ifdef HAS_SCREEN
-    display_obj.tft.drawCentreString("ESP32 Marauder", TFT_WIDTH/2, TFT_HEIGHT * 0.33, 1);
-    display_obj.tft.drawCentreString("JustCallMeKoko", TFT_WIDTH/2, TFT_HEIGHT * 0.5, 1);
-    display_obj.tft.drawCentreString(display_obj.version_number, TFT_WIDTH/2, TFT_HEIGHT * 0.66, 1);
-  #endif


  backlightOn(); // Need this
@@ -248,29 +264,16 @@ void setup()

  settings_obj.begin();

-  wifi_scan_obj.RunSetup();
-
-  //#ifdef HAS_SCREEN
-  //  display_obj.tft.println(F(text_table0[2]));
-  //#endif
-
  buffer_obj = Buffer();
  #if defined(HAS_SD)
    // Do some SD stuff
-    if(sd_obj.initSD()) {
-      #ifdef HAS_SCREEN
-        //display_obj.tft.println(F(text_table0[3]));
-      #endif
-    } else {
+    if(!sd_obj.initSD())
      Serial.println(F("SD Card NOT Supported"));
-      #ifdef HAS_SCREEN
-        //display_obj.tft.setTextColor(TFT_RED, TFT_BLACK);
-        //display_obj.tft.println(F(text_table0[4]));
-        //display_obj.tft.setTextColor(TFT_CYAN, TFT_BLACK);
-      #endif
-    }
+
  #endif

+  wifi_scan_obj.RunSetup();
+
  #ifdef HAS_SCREEN
    display_obj.tft.setTextColor(TFT_GREEN, TFT_BLACK);
    display_obj.tft.drawCentreString("Initializing...", TFT_WIDTH/2, TFT_HEIGHT * 0.82, 1);
@@ -281,21 +284,13 @@ void setup()
  #ifdef HAS_BATTERY
    battery_obj.RunSetup();
  #endif
-  
-  #ifdef HAS_SCREEN
-    //display_obj.tft.println(F(text_table0[5]));
-  #endif
-
-  #ifdef HAS_SCREEN
-    //display_obj.tft.println(F(text_table0[6]));
-  #endif

  #ifdef HAS_BATTERY
    battery_obj.battery_level = battery_obj.getBatteryLevel();
  #endif

  // Do some LED stuff
-  #ifdef MARAUDER_FLIPPER
+  #ifdef HAS_FLIPPER_LED
    flipper_led.RunSetup();
  #elif defined(XIAO_ESP32_S3)
    xiao_led.RunSetup();
@@ -305,28 +300,12 @@ void setup()
    led_obj.RunSetup();
  #endif

-  #ifdef HAS_SCREEN
-    //display_obj.tft.println(F(text_table0[7]));
-
-    //delay(500);
-  #endif
-
  #ifdef HAS_GPS
    gps_obj.begin();
-    //#ifdef HAS_SCREEN
-      //if (gps_obj.getGpsModuleStatus())
-        //display_obj.tft.println("GPS Module connected");
-      //else
-        //display_obj.tft.println("GPS Module NOT connected");
-    //#endif
  #endif

-  #ifdef HAS_SCREEN
-    //display_obj.tft.println(F(text_table0[8]));
-  
+  #ifdef HAS_SCREEN  
    display_obj.tft.setTextColor(TFT_WHITE, TFT_BLACK);
-  
-    //delay(2000);
  #endif

  #ifdef HAS_SCREEN
@@ -346,10 +325,12 @@ void loop()
  bool mini = false;

  #ifdef SCREEN_BUFFER
-    mini = true;
+    #ifndef HAS_ILI9341
+      mini = true;
+    #endif
  #endif

-  #ifdef HAS_ILI9341
+  #if (defined(HAS_ILI9341) && !defined(MARAUDER_CYD_2USB))
    #ifdef HAS_BUTTONS
      if (c_btn.isHeld()) {
        if (menu_function_obj.disable_touch)
@@ -366,20 +347,11 @@ void loop()
  #endif

  // Update all of our objects
-  /*#ifdef HAS_SCREEN
-    bool do_draw = display_obj.draw_tft;
-  #else
-    bool do_draw = false;
-  #endif*/
-  
-  //if ((!do_draw) && (wifi_scan_obj.currentScanMode != ESP_UPDATE))
-  //{
  cli_obj.main(currentTime);
  #ifdef HAS_SCREEN
    display_obj.main(wifi_scan_obj.currentScanMode);
  #endif
  wifi_scan_obj.main(currentTime);
-  //evil_portal_obj.main(wifi_scan_obj.currentScanMode);

  #ifdef HAS_GPS
    gps_obj.main();
@@ -395,7 +367,6 @@ void loop()

  #ifdef HAS_BATTERY
    battery_obj.main(currentTime);
-    //temp_obj.main(currentTime);
  #endif
  settings_obj.main(currentTime);
  if (((wifi_scan_obj.currentScanMode != WIFI_PACKET_MONITOR) && (wifi_scan_obj.currentScanMode != WIFI_SCAN_EAPOL)) ||
@@ -403,9 +374,8 @@ void loop()
    #ifdef HAS_SCREEN
      menu_function_obj.main(currentTime);
    #endif
-    //cli_obj.main(currentTime);
  }
-  #ifdef MARAUDER_FLIPPER
+  #ifdef HAS_FLIPPER_LED
    flipper_led.main();
  #elif defined(XIAO_ESP32_S3)
    xiao_led.main();
@@ -415,29 +385,9 @@ void loop()
    led_obj.main(currentTime);
  #endif

-  //if (wifi_scan_obj.currentScanMode == OTA_UPDATE)
-  //  web_obj.main();
  #ifdef HAS_SCREEN
    delay(1);
  #else
    delay(50);
  #endif
-  //}
-  /*else if (wifi_scan_obj.currentScanMode == ESP_UPDATE) {
-    #ifdef HAS_SCREEN
-      display_obj.main(wifi_scan_obj.currentScanMode);
-      menu_function_obj.main(currentTime);
-    #endif
-
-    #ifdef MARAUDER_FLIPPER
-      flipper_led.main();
-    #elif defined(XIAO_ESP32_S3)
-      xiao_led.main();
-    #else
-      led_obj.main(currentTime);
-    #endif
-    
-    //cli_obj.main(currentTime);
-    delay(1);
-  }*/
 }
--- a/esp32_marauder/flipperLED.cpp
+++ b/esp32_marauder/flipperLED.cpp
@@ -1,5 +1,7 @@
 #include "flipperLED.h"

+#ifdef HAS_FLIPPER_LED
+
 void flipperLED::RunSetup() {
  pinMode(B_PIN, OUTPUT);
  pinMode(G_PIN, OUTPUT);
@@ -58,4 +60,6 @@ void flipperLED::offLED() {

 void flipperLED::main() {
  // do nothing
-}
+}
+
+#endif
--- a/esp32_marauder/flipperLED.h
+++ b/esp32_marauder/flipperLED.h
@@ -8,10 +8,6 @@

 #include <Arduino.h>

-#define B_PIN 4
-#define G_PIN 5
-#define R_PIN 6
-
 extern Settings settings_obj;

 class flipperLED {
--- a/esp32_marauder/lang_var.h
+++ b/esp32_marauder/lang_var.h
@@ -103,7 +103,9 @@ PROGMEM const char text1_59[] = "Station Sniff";
 PROGMEM const char text1_60[] = "Clear Stations";
 PROGMEM const char text1_61[] = "Select Stations";
 PROGMEM const char text1_62[] = "Deauth Targeted";
-
+PROGMEM const char text1_63[] = "Detect Pineapple";
+PROGMEM const char text1_64[] = "Detect MultiSSID";
+PROGMEM const char text1_65[] = "Select probe SSIDs";

 //SDInterface.cpp texts
 PROGMEM const char text2_0[] = "Error, could not find update.bin";
@@ -179,12 +181,14 @@ PROGMEM const char text4_44[] = " AP Scan ";
 PROGMEM const char text4_45[] = "Clearing Stations...";
 PROGMEM const char text4_46[] = "Stations Cleared: ";
 PROGMEM const char text4_47[] = "Targeted Deauth";
+PROGMEM const char text4_48[] = " Detect Pineapple ";
+PROGMEM const char text4_49[] = " Detect MultiSSID ";

 //Making tables
 PROGMEM const char *text_table0[] = {text0_0,text0_1, text0_2, text0_3, text0_4, text0_5, text0_6, text0_7, text0_8};
-PROGMEM const char *text_table1[] = {text1_0,text1_1,text1_2,text1_3,text1_4,text1_5,text1_6,text1_7,text1_8,text1_9,text1_10,text1_11,text1_12,text1_13,text1_14,text1_15,text1_16,text1_17,text1_18,text1_19,text1_20,text1_21,text1_22,text1_23,text1_24,text1_25,text1_26,text1_27,text1_28,text1_29,text1_30,text1_31,text1_32,text1_33,text1_34,text1_35,text1_36,text1_37,text1_38,text1_39,text1_40,text1_41,text1_42,text1_43,text1_44,text1_45,text1_46,text1_47,text1_48,text1_49,text1_50,text1_51,text1_52,text1_53,text1_54,text1_55,text1_56,text1_57,text1_58,text1_59,text1_60,text1_61,text1_62};
+PROGMEM const char *text_table1[] = {text1_0,text1_1,text1_2,text1_3,text1_4,text1_5,text1_6,text1_7,text1_8,text1_9,text1_10,text1_11,text1_12,text1_13,text1_14,text1_15,text1_16,text1_17,text1_18,text1_19,text1_20,text1_21,text1_22,text1_23,text1_24,text1_25,text1_26,text1_27,text1_28,text1_29,text1_30,text1_31,text1_32,text1_33,text1_34,text1_35,text1_36,text1_37,text1_38,text1_39,text1_40,text1_41,text1_42,text1_43,text1_44,text1_45,text1_46,text1_47,text1_48,text1_49,text1_50,text1_51,text1_52,text1_53,text1_54,text1_55,text1_56,text1_57,text1_58,text1_59,text1_60,text1_61,text1_62,text1_63,text1_64, text1_65};
 PROGMEM const char *text_table2[] = {text2_0,text2_1,text2_2,text2_3,text2_4,text2_5,text2_6,text2_7,text2_8,text2_9,text2_10,text2_11,text2_12,text2_13,text2_14};
 PROGMEM const char *text_table3[] = {text3_0,text3_1,text3_2,text3_3,text3_4,text3_5};
-PROGMEM const char *text_table4[] = {text4_0,text4_1,text4_2,text4_3,text4_4,text4_5,text4_6,text4_7,text1_54,text4_9,text4_10,text4_11,text4_12,text4_13,text4_14,text4_15,text4_16,text4_17,text4_18,text4_19,text4_20,text4_21,text4_22,text4_23,text4_24,text4_25,text4_26,text4_27,text4_28,text4_29,text4_30,text4_31,text4_32,text4_33,text4_34,text4_35,text4_36,text4_37,text4_38,text4_39,text4_40,text4_41,text4_42,text4_43,text4_44,text4_45,text4_46,text4_47};
+PROGMEM const char *text_table4[] = {text4_0,text4_1,text4_2,text4_3,text4_4,text4_5,text4_6,text4_7,text1_54,text4_9,text4_10,text4_11,text4_12,text4_13,text4_14,text4_15,text4_16,text4_17,text4_18,text4_19,text4_20,text4_21,text4_22,text4_23,text4_24,text4_25,text4_26,text4_27,text4_28,text4_29,text4_30,text4_31,text4_32,text4_33,text4_34,text4_35,text4_36,text4_37,text4_38,text4_39,text4_40,text4_41,text4_42,text4_43,text4_44,text4_45,text4_46,text4_47,text4_48,text4_49};

 #endif
--- a/esp32_marauder/utils.h
+++ b/esp32_marauder/utils.h
@@ -4,6 +4,11 @@

 #include <Arduino.h>
 #include <vector>
+#include <WiFi.h>
+
+#include "configs.h"
+
+#include "esp_heap_caps.h"

 struct mac_addr {
   unsigned char bytes[6];
@@ -12,8 +17,174 @@ struct mac_addr {
 struct Station {
  uint8_t mac[6];
  bool selected;
+  uint16_t packets;
+  uint16_t ap;
 };

+struct ProbeReqSsid {
+    String essid;
+    bool selected;
+    uint8_t requests;
+};
+
+const char apple_ouis[][9] PROGMEM = {
+  "00:17:F2", "00:1E:C2", "00:26:08", "F8:1E:DF", "BC:92:6B", 
+  "28:E0:2C", "3C:07:54", "7C:D1:C3", "DC:A9:04", "F0:D1:A9",
+  "C0:2C:5C", "00:03:93", "00:03:94", "00:03:95", "00:03:96",
+  "00:03:97", "00:03:98", "00:03:99", "00:03:9A", "00:03:9B",
+  "00:03:9C", "00:03:9D", "00:03:9E", "00:03:9F", "00:03:A0",
+  "00:03:A1", "00:03:A2", "00:03:A3", "00:03:A4", "00:03:A5",
+  "00:03:A6", "00:03:A7", "00:03:A8", "00:03:A9", "00:03:AA",
+  "00:03:AB", "00:03:AC", "00:03:AD", "00:03:AE", "00:03:AF",
+  "00:03:B0", "00:03:B1", "00:03:B2", "00:03:B3", "00:03:B4",
+  "00:03:B5", "00:03:B6", "00:03:B7", "00:03:B8", "00:03:B9",
+  "00:03:BA", "00:03:BB", "00:03:BC", "00:03:BD", "00:03:BE",
+  "00:03:BF", "00:03:C0", "00:03:C1", "00:03:C2", "00:03:C3",
+  "00:03:C4", "00:03:C5", "00:03:C6", "00:03:C7", "00:03:C8",
+  "00:03:C9", "00:03:CA", "00:03:CB", "00:03:CC", "00:03:CD",
+  "00:03:CE", "00:03:CF", "00:03:D0", "00:03:D1", "00:03:D2",
+  "00:03:D3", "00:03:D4", "00:03:D5", "00:03:D6", "00:03:D7",
+  "00:03:D8", "00:03:D9", "00:03:DA", "00:03:DB", "00:03:DC",
+  "00:03:DD", "00:03:DE", "00:03:DF", "00:03:E0", "00:03:E1",
+  "00:03:E2", "00:03:E3", "00:03:E4", "00:03:E5", "00:03:E6",
+  "00:03:E7", "00:03:E8", "00:03:E9", "00:03:EA", "00:03:EB",
+  "00:03:EC", "00:03:ED", "00:03:EE", "00:03:EF", "00:03:F0",
+  "00:03:F1", "00:03:F2", "00:03:F3", "00:03:F4", "00:03:F5",
+  "00:03:F6", "00:03:F7", "00:03:F8", "00:03:F9", "00:03:FA",
+  "00:03:FB", "00:03:FC", "00:03:FD", "00:03:FE", "00:03:FF"
+};
+
+const char asus_ouis[][9] PROGMEM = {
+  "00:0C:6E", "00:0E:A6", "00:11:2F", "00:11:D8", "00:13:D4", "00:15:F2", "00:17:31", "00:18:F3", "00:1A:92",
+  "00:1B:FC", "00:1D:60", "00:1E:8C", "00:1F:C6", "00:22:15", "00:23:54", "00:24:8C", "00:26:18", "00:E0:18",
+  "04:42:1A", "04:92:26", "04:D4:C4", "04:D9:F5", "08:60:6E", "08:62:66", "08:BF:B8", "0C:9D:92", "10:7B:44",
+  "10:7C:61", "10:BF:48", "10:C3:7B", "14:DA:E9", "14:DD:A9", "18:31:BF", "1C:87:2C", "1C:B7:2C", "20:CF:30",
+  "24:4B:FE", "2C:4D:54", "2C:56:DC", "2C:FD:A1", "30:5A:3A", "30:85:A9", "34:97:F6", "38:2C:4A", "38:D5:47",
+  "3C:7C:3F", "40:16:7E", "40:B0:76", "48:5B:39", "4C:ED:FB", "50:46:5D", "50:EB:F6", "54:04:A6", "54:A0:50",
+  "58:11:22", "60:45:CB", "60:A4:4C", "60:CF:84", "70:4D:7B", "70:8B:CD", "74:D0:2B", "78:24:AF", "7C:10:C9",
+  "88:D7:F6", "90:E6:BA", "9C:5C:8E", "A0:36:BC", "A8:5E:45", "AC:22:0B", "AC:9E:17", "B0:6E:BF", "BC:AE:C5",
+  "BC:EE:7B", "C8:60:00", "C8:7F:54", "CC:28:AA", "D0:17:C2", "D4:5D:64", "D8:50:E6", "E0:3F:49", "E0:CB:4E",
+  "E8:9C:25", "F0:2F:74", "F0:79:59", "F4:6D:04", "F8:32:E4", "FC:34:97", "FC:C2:33"
+};
+
+const char belkin_ouis[][9] PROGMEM = {
+  "00:11:50", "00:17:3F", "00:30:BD", "08:BD:43", "14:91:82", "24:F5:A2", "30:23:03", "80:69:1A", "94:10:3E",
+  "94:44:52", "B4:75:0E", "C0:56:27", "C4:41:1E", "D8:EC:5E", "E8:9F:80", "EC:1A:59", "EC:22:80"
+};
+
+const char cisco_ouis[][9] PROGMEM = {
+  "00:1B:0D", "00:1D:45", "00:1E:7A", "00:25:9C", "00:50:56", 
+  "40:55:39", "58:8D:09", "A4:4C:C8", "F8:0F:F9"
+};
+
+const char dlink_ouis[][9] PROGMEM = {
+  "00:05:5D", "00:0D:88", "00:0F:3D", "00:11:95", "00:13:46", "00:15:E9", "00:17:9A", "00:19:5B", "00:1B:11",
+  "00:1C:F0", "00:1E:58", "00:21:91", "00:22:B0", "00:24:01", "00:26:5A", "00:AD:24", "04:BA:D6", "08:5A:11",
+  "0C:0E:76", "0C:B6:D2", "10:62:EB", "10:BE:F5", "14:D6:4D", "18:0F:76", "1C:5F:2B", "1C:7E:E5", "1C:AF:F7",
+  "1C:BD:B9", "28:3B:82", "30:23:03", "34:08:04", "34:0A:33", "3C:1E:04", "3C:33:32", "40:86:CB", "40:9B:CD",
+  "54:B8:0A", "5C:D9:98", "60:63:4C", "64:29:43", "6C:19:8F", "6C:72:20", "74:44:01", "74:DA:DA", "78:32:1B",
+  "78:54:2E", "78:98:E8", "80:26:89", "84:C9:B2", "88:76:B9", "90:8D:78", "90:94:E4", "9C:D6:43", "A0:63:91",
+  "A0:AB:1B", "A4:2A:95", "A8:63:7D", "AC:F1:DF", "B4:37:D8", "B8:A3:86", "BC:0F:9A", "BC:22:28", "BC:F6:85",
+  "C0:A0:BB", "C4:A8:1D", "C4:E9:0A", "C8:78:7D", "C8:BE:19", "C8:D3:A3", "CC:B2:55", "D8:FE:E3", "DC:EA:E7",
+  "E0:1C:FC", "E4:6F:13", "E8:CC:18", "EC:22:80", "EC:AD:E0", "F0:7D:68", "F0:B4:D2", "F4:8C:EB", "F8:E9:03",
+  "FC:75:16"
+};
+
+const char google_ouis[][9] PROGMEM = {
+  "3C:5A:B4", "5C:BF:C0", "78:4F:43", "A4:77:33", "D4:97:0B", "F0:72:8C"
+};
+
+const char huawei_ouis[][9] PROGMEM = {
+  "00:1A:2B", "28:FF:3C", "5C:4C:A9", "8C:71:F8", "C8:D1:5E", 
+  "E4:4C:A9", "F4:12:FA"
+};
+
+const char lg_ouis[][9] PROGMEM = {
+  "00:17:C0", "18:AF:8F", "38:2D:AE", "5C:87:9C", "68:27:37", 
+  "78:5D:C8", "94:65:2D", "A4:77:33", "C4:43:8F"
+};
+
+const char linksys_ouis[][9] PROGMEM = {
+  "00:04:5A", "00:06:25", "00:0C:41", "00:0E:08", "00:0F:66", "00:12:17", "00:13:10", "00:14:BF", "00:16:B6",
+  "00:18:39", "00:18:F8", "00:1A:70", "00:1C:10", "00:1D:7E", "00:1E:E5", "00:21:29", "00:22:6B", "00:23:69",
+  "00:25:9C", "00:23:54", "00:24:B2", "00:31:92", "00:5F:67", "10:27:F5", "14:EB:B6", "1C:61:B4", "20:36:26",
+  "28:87:BA", "30:5A:3A", "2C:FD:A1", "30:23:03", "30:46:9A", "40:ED:00", "48:22:54", "50:91:E3", "54:AF:97",
+  "5C:A2:F4", "5C:A6:E6", "5C:E9:31", "60:A4:B7", "68:7F:F0", "6C:5A:B0", "78:8C:B5", "7C:C2:C6", "9C:53:22",
+  "9C:A2:F4", "A8:42:A1", "AC:15:A2", "B0:A7:B9", "B4:B0:24", "C0:06:C3", "CC:68:B6", "E8:48:B8", "F0:A7:31"
+};
+
+const char netgear_ouis[][9] PROGMEM = {
+  "00:09:5B", "00:0F:B5", "00:14:6C", "00:1B:2F", "00:1E:2A", "00:1F:33", "00:22:3F", "00:22:4B", "00:26:F2",
+  "00:8E:F2", "08:02:8E", "08:36:C9", "08:BD:43", "10:0C:6B", "10:0D:7F", "10:DA:43", "14:59:C0", "20:4E:7F",
+  "20:E5:2A", "28:80:88", "28:94:01", "28:C6:8E", "2C:30:33", "2C:B0:5D", "30:46:9A", "34:98:B5", "38:94:ED",
+  "3C:37:86", "40:5D:82", "44:A5:6E", "4C:60:DE", "50:4A:6E", "50:6A:03", "54:07:7D", "58:EF:68", "60:38:E0",
+  "6C:B0:CE", "6C:CD:D6", "74:44:01", "80:37:73", "84:1B:5E", "8C:3B:AD", "94:18:65", "9C:3D:CF", "9C:C9:EB",
+  "9C:D3:6D", "A0:04:60", "A0:21:B7", "A0:40:A0", "A4:2B:8C", "B0:39:56", "B0:7F:B9", "B0:B9:8A", "BC:A5:11",
+  "C0:3F:0E", "C0:FF:D4", "C4:04:15", "C4:3D:C7", "C8:9E:43", "CC:40:D0", "DC:EF:09", "E0:46:9A", "E0:46:EE",
+  "E0:91:F5", "E4:F4:C6", "E8:FC:AF", "F8:73:94"
+};
+
+const char oneplus_ouis[][9] PROGMEM = {
+  "08:EC:A9", "30:9C:23", "38:78:62", "64:A2:F9", "74:AC:B9", 
+  "A8:14:51", "B4:86:55", "D8:CB:8A", "F4:8C:50"
+};
+
+const char samsung_ouis[][9] PROGMEM = {
+  "00:12:47", "00:15:99", "00:16:6B", "00:1B:FC", "10:5F:06", 
+  "18:59:36", "20:02:AF", "24:4B:03", "38:2D:3D", "40:B8:37",
+  "00:1F:12", "00:1D:0F", "00:1A:9A", "00:19:E1", "00:18:FF", 
+  "00:17:77", "00:16:72", "00:14:69", "00:13:65", "00:12:60",
+  "30:37:0D", "40:8C:47", "50:55:5F", "60:47:A1", "70:0A:AD",
+  "80:61:43", "90:48:F7", "A0:4C:CB", "B0:5E:93", "C0:3D:F5",
+  "D0:31:AA", "E0:4F:02", "F0:3B:94"
+};
+
+const char sony_ouis[][9] PROGMEM = {
+  "00:19:C5", "00:1B:59", "00:1E:DC", "10:68:3F", "54:42:49", 
+  "A8:E3:EE", "B8:F9:34", "CC:5D:4E", "E8:89:2F"
+};
+
+const char tplink_ouis[][9] PROGMEM = {
+  "00:31:92", "00:5F:67", "10:27:F5", "14:EB:B6", "1C:61:B4", "20:36:26", "28:87:BA", "30:DE:4B", "34:60:F9",
+  "3C:52:A1", "40:ED:00", "48:22:54", "50:91:E3", "54:AF:97", "5C:62:8B", "5C:A6:E6", "5C:E9:31", "60:A4:B7",
+  "68:7F:F0", "6C:5A:B0", "78:8C:B5", "7C:C2:C6", "9C:53:22", "9C:A2:F4", "A8:42:A1", "AC:15:A2", "B0:A7:B9",
+  "B4:B0:24", "C0:06:C3", "CC:68:B6", "E8:48:B8", "F0:A7:31"
+};
+
+const char xiaomi_ouis[][9] PROGMEM = {
+  "04:CF:8C", "18:59:36", "38:1A:2D", "64:B4:73", "78:02:F8", 
+  "90:4E:91", "C4:0B:CB", "D0:DB:32"
+};
+
+uint8_t getDRAMUsagePercent() {
+  //size_t total = heap_caps_get_total_size(MALLOC_CAP_8BIT);
+  //size_t free = heap_caps_get_free_size(MALLOC_CAP_8BIT);
+  size_t free = ESP.getFreeHeap();
+  size_t total = ESP.getHeapSize();
+  
+  if (total == 0) return 0; // Avoid division by zero
+
+  size_t used = total - free;
+  uint8_t percent = (used * 100) / total;
+  return percent;
+}
+
+#ifdef HAS_PSRAM
+  uint8_t getPSRAMUsagePercent() {
+    //size_t total = heap_caps_get_total_size(MALLOC_CAP_SPIRAM);
+    //size_t free  = heap_caps_get_free_size(MALLOC_CAP_SPIRAM);
+
+    size_t total = ESP.getPsramSize();
+    size_t free = ESP.getFreePsram();
+
+    if (total == 0) return 0; // Avoid division by zero or PSRAM not available
+
+    size_t used = total - free;
+    uint8_t percent = (used * 100) / total;
+    return percent;
+  }
+#endif
+
 String byteArrayToHexString(const std::vector<uint8_t>& byteArray) {
  String result;

@@ -127,4 +298,92 @@ void convertMacStringToUint8(const String& macStr, uint8_t macAddr[6]) {
    }
 }

+// Function to check if the given MAC address matches any known OUI
+const char* getManufacturer(const char *addr) {
+  static char oui[9]; // Temporary buffer for extracted OUI
+
+  // Extract the first three bytes (OUI) from addr
+  strncpy(oui, addr, 8);
+  oui[8] = '\0'; // Ensure null termination
+
+  // Convert the addr (OUI) to lowercase
+  for (int i = 0; i < 8; i++) {
+    oui[i] = tolower(oui[i]);
+  }
+
+  // Helper macro to check against an array stored in PROGMEM
+  #define CHECK_OUI(manufacturer, list) \
+    for (uint8_t i = 0; i < sizeof(list) / sizeof(list[0]); i++) { \
+      char storedOUI[9]; \
+      strcpy_P(storedOUI, list[i]); \
+      /* Convert the stored OUI to lowercase */ \
+      for (int j = 0; j < 8; j++) { \
+        storedOUI[j] = tolower(storedOUI[j]); \
+      } \
+      if (strcmp(oui, storedOUI) == 0) return manufacturer; \
+    }
+
+  // Check against known manufacturers
+  CHECK_OUI("Apple", apple_ouis);
+  CHECK_OUI("Asus", asus_ouis);
+  CHECK_OUI("Belkin", belkin_ouis);
+  CHECK_OUI("Cisco", cisco_ouis);
+  CHECK_OUI("DLink", dlink_ouis);
+  CHECK_OUI("Google", google_ouis);
+  CHECK_OUI("Huawei", huawei_ouis);
+  CHECK_OUI("LG", lg_ouis);
+  CHECK_OUI("Linksys", linksys_ouis);
+  CHECK_OUI("Netgear", netgear_ouis);
+  CHECK_OUI("OnePlus", oneplus_ouis);
+  CHECK_OUI("Samsung", samsung_ouis);
+  CHECK_OUI("Sony", sony_ouis);
+  CHECK_OUI("TP-Link", tplink_ouis);
+  CHECK_OUI("Xiaomi", xiaomi_ouis);
+
+  return ""; // Return "Unknown" if no match is found
+}
+
+String replaceOUIWithManufacturer(const char *sta_addr) {
+  const char *manufacturer = getManufacturer(sta_addr);
+
+  if (manufacturer == nullptr || strlen(manufacturer) == 0) {
+    return String(sta_addr); // Return original if no manufacturer found
+  }
+
+  // Skip the first 8 characters (3 bytes and 2 colons)
+  const char *mac_suffix = sta_addr + 8;
+
+  // Construct the new address: manufacturer + the remaining MAC address (after the first 3 bytes)
+  return String(manufacturer) + mac_suffix;
+}
+
+IPAddress getNextIP(IPAddress currentIP, IPAddress subnetMask) {
+  // Convert IPAddress to uint32_t
+  uint32_t ipInt = (currentIP[0] << 24) | (currentIP[1] << 16) | (currentIP[2] << 8) | currentIP[3];
+  uint32_t maskInt = (subnetMask[0] << 24) | (subnetMask[1] << 16) | (subnetMask[2] << 8) | subnetMask[3];
+
+  uint32_t networkBase = ipInt & maskInt;
+  uint32_t broadcast = networkBase | ~maskInt;
+
+  uint32_t nextIP = ipInt + 1;
+
+  if (nextIP <= networkBase) {
+    nextIP = networkBase + 1;
+  }
+  if (nextIP >= broadcast) {
+    return IPAddress(0, 0, 0, 0); // no more IPs
+  }
+
+  return IPAddress(
+    (nextIP >> 24) & 0xFF,
+    (nextIP >> 16) & 0xFF,
+    (nextIP >> 8) & 0xFF,
+    nextIP & 0xFF
+  );
+}
+
+uint16_t getNextPort(uint16_t port) {
+  return port + 1;
+}
+
 #endif
--- a/mechanical/Flipper
+++ b/mechanical/Flipper
--- a/mechanical/Flipper
+++ b/mechanical/Flipper
--- a/Board/Wifi_Dev_REAR_THRUBOLT_STD_GPS_ANT.stl
+++ b/Board/Wifi_Dev_REAR_THRUBOLT_STD_GPS_ANT.stl
--- a/Fix/DSC05049-Edit.jpg
+++ b/Fix/DSC05049-Edit.jpg
--- a/Fix/DSC05050.jpg
+++ b/Fix/DSC05050.jpg
--- a/pictures/c5_marauder_flipper_adapter.png
+++ b/pictures/c5_marauder_flipper_adapter.png
--- a/pictures/icons/force_16.bmp
+++ b/pictures/icons/force_16.bmp
--- a/pictures/icons/joined_16.bmp
+++ b/pictures/icons/joined_16.bmp
--- a/pictures/icons/pineapple_22.bmp
+++ b/pictures/icons/pineapple_22.bmp
--- a/pictures/marauder_skull_240x320-01-01.png
+++ b/pictures/marauder_skull_240x320-01-01.png
--- a/pictures/marauder_skull_patch_04_full_final.png
+++ b/pictures/marauder_skull_patch_04_full_final.png
--- a/pictures/xbm/force_16.xbm
+++ b/pictures/xbm/force_16.xbm
@@ -0,0 +1,6 @@
+#define 3f9b97ac7933453c85ec3a8adb49feeejQ9bt0wTgiC65w8g_width 16
+#define 3f9b97ac7933453c85ec3a8adb49feeejQ9bt0wTgiC65w8g_height 16
+static char 3f9b97ac7933453c85ec3a8adb49feeejQ9bt0wTgiC65w8g_bits[] = {
+  0xFF, 0xFF, 0x1F, 0xF8, 0x0F, 0xF0, 0x07, 0xE0, 0x07, 0xE0, 0x07, 0xE0, 
+  0x67, 0xE6, 0x77, 0xEE, 0x87, 0xE0, 0x8F, 0xF1, 0x0F, 0xF0, 0x4F, 0xF5, 
+  0x1F, 0xF8, 0x3F, 0xFC, 0xFF, 0xFF, 0xFF, 0xFF, };
--- a/pictures/xbm/joined_16.xbm
+++ b/pictures/xbm/joined_16.xbm
@@ -0,0 +1,6 @@
+#define 67ae760eaaa64924c492c46151d37f46mewyG1NBArKDOITT_width 16
+#define 67ae760eaaa64924c492c46151d37f46mewyG1NBArKDOITT_height 16
+static char 67ae760eaaa64924c492c46151d37f46mewyG1NBArKDOITT_bits[] = {
+  0xFF, 0xFF, 0xFF, 0xFF, 0x07, 0xFF, 0xFF, 0xFC, 0xFF, 0xF3, 0x87, 0xF7, 
+  0x7F, 0xEE, 0xFF, 0xED, 0xC7, 0xDD, 0xBF, 0xDB, 0x7F, 0xDB, 0x67, 0xDB, 
+  0x67, 0xDB, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, };
--- a/pictures/xbm/pineapple_22.xbm
+++ b/pictures/xbm/pineapple_22.xbm
@@ -0,0 +1,9 @@
+#define be52a82b6ef24281d57d9491aef1484cv5n1Pq988C5WdKha_width 22
+#define be52a82b6ef24281d57d9491aef1484cv5n1Pq988C5WdKha_height 22
+static char be52a82b6ef24281d57d9491aef1484cv5n1Pq988C5WdKha_bits[] = {
+  0xFF, 0xFF, 0x3F, 0xFF, 0xF7, 0x3F, 0x7F, 0x96, 0x3F, 0xFF, 0xED, 0x3F, 
+  0x3F, 0x25, 0x3F, 0xDF, 0xD2, 0x3E, 0xFF, 0xED, 0x3F, 0x7F, 0x8E, 0x3F, 
+  0x3B, 0x77, 0x37, 0xBD, 0x6A, 0x2F, 0xD6, 0xBD, 0x1A, 0xDA, 0xDA, 0x16, 
+  0x5A, 0x6F, 0x16, 0x9A, 0xF7, 0x16, 0xD6, 0x5A, 0x1A, 0xDD, 0xBD, 0x2E, 
+  0xBB, 0x5A, 0x37, 0x3F, 0x6F, 0x3F, 0x7F, 0xB7, 0x3F, 0xFF, 0xCC, 0x3F, 
+  0xFF, 0xF3, 0x3F, 0xFF, 0xFF, 0x3F, };
Author	SHA1	Message	Date
Just Call Me Koko	2c2df227d2	Merge pull request #840 from justcallmekoko/develop Merge develop into master	2025-07-22 09:59:16 -04:00
Just Call Me Koko	ede779845c	Merge pull request #839 from justcallmekoko/marauder_c5 Add C5 flasher	2025-07-22 09:54:01 -04:00
Just Call Me Koko	9c62237fcf	Add C5 flasher	2025-07-22 09:40:56 -04:00
Just Call Me Koko	7966b07441	Merge pull request #838 from justcallmekoko/develop Merge develop into master	2025-07-21 19:24:29 -04:00
Just Call Me Koko	158644092c	Merge pull request #837 from justcallmekoko/marauder_c5 Add support for M5 Cardputer	2025-07-21 19:19:13 -04:00
Just Call Me Koko	9411128cca	Fix board definition	2025-07-21 18:55:12 -04:00
Just Call Me Koko	530a30c6d7	Add support for M5 Cardputer	2025-07-21 18:47:57 -04:00
Just Call Me Koko	ee7e3f1d1e	Merge pull request #836 from justcallmekoko/marauder_c5 Add support for ESP32-C5 DevKit	2025-07-21 18:45:51 -04:00
Just Call Me Koko	3d9b91a80b	Adjust wardriving coverage for C5	2025-07-10 13:40:47 -04:00
Just Call Me Koko	07a3e54498	Silly little C5 SD card stuff	2025-07-10 12:23:37 -04:00
Just Call Me Koko	9a25224c83	Marauder compiles and installs for ESP32-C5	2025-07-10 11:20:50 -04:00
Just Call Me Koko	44189ff945	Merge pull request #826 from justcallmekoko/develop Develop	2025-07-07 19:04:24 -04:00
Just Call Me Koko	d61542eb5f	Merge pull request #825 from justcallmekoko/captiveportal captiveportal	2025-07-07 17:26:10 -04:00
Just Call Me Koko	e0eb37e082	Merge pull request #824 from bpmcircuits/captiveportal-dev Added captive endpoints redirection to index.html file.	2025-07-07 17:14:37 -04:00
Just Call Me Koko	17338427a1	Fix BLE spam crash	2025-07-07 17:10:55 -04:00
Bartek Pokrywka	a10bb164ac	Added captive endopints redirection to index_html	2025-07-07 16:52:27 +02:00
Bartek Pokrywka	b43a79e036	Added captive endopints redirection to index_html	2025-07-07 16:49:24 +02:00
Just Call Me Koko	1cdb9b4a17	Merge pull request #813 from justcallmekoko/develop Increment version number	2025-06-24 13:16:52 -04:00
Just Call Me Koko	c117eebc0f	Increment version number	2025-06-24 13:11:26 -04:00
Just Call Me Koko	303a9d2eeb	Merge pull request #812 from justcallmekoko/develop Fix S3 PSRAM and BLE transmit stop, Add probe SSID list	2025-06-24 11:54:05 -04:00
Just Call Me Koko	a101bfdddf	Merge pull request #811 from justcallmekoko/probe Select SSIDs from Probe Request Sniff	2025-06-24 11:39:05 -04:00
Just Call Me Koko	a0ed27308e	Merge pull request #803 from m1crod0t/Select_SSIDs_from_Probe Select SSIDs from Probe Request Sniff #796	2025-06-24 09:00:22 -04:00
Just Call Me Koko	2362b8e8c5	Merge pull request #809 from WillyJL/fix/s3-psram Fix multiboardS3 builds, fix BLE spam not stopping	2025-06-24 08:43:39 -04:00
WillyJL	0ca43eb403	Fix multiboardS3 builds, fix BLE spam not stopping	2025-06-21 04:49:29 +01:00
m1crod0t	b76de6c314	Update WiFiScan.cpp Intendent issue	2025-06-11 15:30:22 +02:00
m1crod0t	d0ac2f178b	Update build_parallel.yml revert to def	2025-06-11 15:25:37 +02:00
m1crod0t	06a5de8cd9	Just intendent	2025-06-11 15:23:18 +02:00
m1crod0t	e300489b77	Update build_parallel.yml	2025-06-10 19:37:04 +02:00
m1crod0t	fe27910096	Update build_parallel.yml	2025-06-10 15:59:03 +02:00
m1crod0t	50b96f696e	Merge pull request #2 from m1crod0t/master Update from master	2025-06-10 15:53:15 +02:00
Just Call Me Koko	35c6d9ca63	Merge pull request #798 from justcallmekoko/develop Update pins for CYD board from fork configs	2025-06-09 14:28:15 -04:00
Just Call Me Koko	07762891d5	Fix wifi channel in status bar	2025-06-09 12:05:27 -04:00
Just Call Me Koko	1278474ca0	Merge pull request #792 from CodeHedge/develop Updated pins for the CYD 2.8" boards	2025-06-09 11:12:25 -04:00
Just Call Me Koko	4874ef3193	Add flipper zero dev board gps enclosure	2025-06-09 11:06:53 -04:00
m1crod0t	a6ed8899c7	Update MenuFunctions.cpp Changed how request count is shown	2025-06-08 17:53:40 +02:00
m1crod0t	2c40d83e3a	Update WiFiScan.cpp Fixed saving request count per ssid	2025-06-08 17:24:54 +02:00
m1crod0t	acef9d437c	Select SSIDs from Probe Request Sniff	2025-06-08 16:09:16 +02:00
Just Call Me Koko	50d876e20f	Merge pull request #791 from justcallmekoko/develop Write IP scan info to logs	2025-06-06 12:48:57 -04:00
hedge	d8512b082c	Updated pins for the CYD 2.8" boards	2025-06-06 09:11:29 -07:00
Just Call Me Koko	dec4b9066f	Write scan info to logs	2025-06-06 10:49:38 -04:00
Just Call Me Koko	dd74b60744	Merge pull request #790 from justcallmekoko/develop Add TCP port scan and Force PMKID status icon	2025-06-06 09:59:37 -04:00
Just Call Me Koko	3a3102d877	Add command for port scan	2025-06-06 09:54:55 -04:00
Just Call Me Koko	38d99bda35	Update status bar format for v7.1	2025-06-05 17:57:51 -04:00
Just Call Me Koko	01660f408d	Add port scan	2025-06-05 15:29:04 -04:00
Just Call Me Koko	5d2c2d553a	Add status icon for force pmkid	2025-06-05 14:04:24 -04:00
Just Call Me Koko	0beb7c455f	Merge pull request #789 from justcallmekoko/develop Add Join WiFi, Ping Scan, and associated commands	2025-06-05 12:23:46 -04:00
Just Call Me Koko	61a7449a89	Fix more non-display stuff	2025-06-05 12:00:42 -04:00
Just Call Me Koko	eb6000a5c3	Fix color definition	2025-06-05 11:46:37 -04:00
Just Call Me Koko	93cb77526f	Add ping command and fix join command	2025-06-05 11:38:37 -04:00
Just Call Me Koko	bade515fb3	Add active IPs to list	2025-06-05 11:05:45 -04:00
Just Call Me Koko	ed95a97506	Connect using set MAC addresses	2025-06-05 10:07:37 -04:00
Just Call Me Koko	ebc3497c32	Add Ping Scan	2025-06-04 20:26:54 -04:00
Just Call Me Koko	38bef9121f	Add network info tracking	2025-06-04 18:59:36 -04:00
Just Call Me Koko	a274e42708	Add wifi connection status icon to status bar	2025-06-04 15:51:26 -04:00
Just Call Me Koko	33d7460c6b	Add join wifi for switch hardware	2025-06-04 11:59:03 -04:00
Just Call Me Koko	51eddd5b8f	Add Join WiFi for touch hardware	2025-06-03 23:13:11 -04:00
Just Call Me Koko	e9e6a84c17	Merge pull request #782 from justcallmekoko/develop Fix display includes	2025-05-31 18:33:42 -04:00
Just Call Me Koko	75e3e71453	Increment version number	2025-05-31 18:29:28 -04:00
Just Call Me Koko	a73da306c9	Fix display includes	2025-05-31 08:26:53 -04:00
Just Call Me Koko	b0a98dbdd6	Merge pull request #781 from justcallmekoko/develop Add build for CYD 2 USB	2025-05-30 16:15:58 -04:00
Just Call Me Koko	09eab04003	Add build for CYD 2 USB	2025-05-30 16:06:41 -04:00
Just Call Me Koko	bed3de7b41	Merge pull request #780 from justcallmekoko/develop Fix SD card init for CYD 2 USB	2025-05-30 13:32:55 -04:00
Just Call Me Koko	a4c0569c7f	Fix SD card init for CYD 2 USB	2025-05-30 13:26:41 -04:00
Just Call Me Koko	dc404f8766	Merge pull request #779 from justcallmekoko/develop Update README.md	2025-05-30 13:01:53 -04:00
Just Call Me Koko	3bc65c2e66	Update README.md	2025-05-30 13:01:33 -04:00
Just Call Me Koko	bced58cf4c	Merge pull request #778 from justcallmekoko/develop Add larger Marauder logo	2025-05-30 13:00:21 -04:00
Just Call Me Koko	289c127871	Add larger Marauder logo	2025-05-30 12:59:57 -04:00
Just Call Me Koko	60e228ee6c	Merge pull request #777 from justcallmekoko/develop Add new Marauder logo	2025-05-30 12:56:28 -04:00
Just Call Me Koko	478c677f6a	Add new Marauder logo	2025-05-30 12:51:24 -04:00
Just Call Me Koko	1307d71c5d	Merge pull request #776 from justcallmekoko/develop Add support for CYD 2 USB and ST7789	2025-05-30 12:40:59 -04:00
Just Call Me Koko	1f08406c63	Repair setup select	2025-05-30 12:30:12 -04:00
Just Call Me Koko	b41597fdac	Add TFT_eSPI setup file for CYD 2 USB	2025-05-30 12:24:26 -04:00
Just Call Me Koko	b6fe3954e6	Create config for CYD 2 USB	2025-05-30 12:22:58 -04:00
Just Call Me Koko	dfa3f5b1f0	Merge pull request #774 from justcallmekoko/develop Add Pineapple and multiSSID sniff	2025-05-28 12:16:06 -04:00
Just Call Me Koko	d4140ffeab	Reformat output strings	2025-05-28 12:10:09 -04:00
Just Call Me Koko	40626ac682	Increment version number	2025-05-28 09:13:10 -04:00
Just Call Me Koko	eb2eadae9f	Add icon image files	2025-05-28 09:03:37 -04:00
Just Call Me Koko	3a24619fe8	Add icons for pineapple and multissid	2025-05-28 09:03:09 -04:00
Just Call Me Koko	806238fdb2	Merge pull request #772 from amec0e/develop Added Pinescan and MultiSSID	2025-05-28 08:42:43 -04:00
amec0e	877fb65ab7	Update WiFiScan.cpp Fixed RunPineScan	2025-05-28 00:24:42 +01:00
amec0e	c8b429e320	Update MenuFunctions.h Uncommented and added Pinescan_sniff and Multissid_Sniff definition	2025-05-28 00:01:38 +01:00
amec0e	ba7c05ff73	Update CommandLine.cpp Added Pinescan and MultiSSID	2025-05-27 23:01:34 +01:00
amec0e	339b9b7c8b	Update CommandLine.h Added Pinescan and MultiSSID	2025-05-27 23:00:22 +01:00
amec0e	aa750ec9b8	Update MenuFunctions.cpp Added Pinescan and MultiSSID	2025-05-27 22:59:29 +01:00
amec0e	7f68fa3aea	Update MenuFunctions.h Added Pinescan and MultiSSID	2025-05-27 22:57:23 +01:00
amec0e	bcb218124f	Merge branch 'justcallmekoko:develop' into develop	2025-05-27 22:55:27 +01:00
amec0e	2631d096c9	Update WiFiScan.cpp Added Pinescan and MultiSSID	2025-05-27 22:55:05 +01:00
Just Call Me Koko	dc2c8e241a	Word wrap signal monitor	2025-05-27 17:53:01 -04:00
amec0e	8f3d0219f0	Update WiFiScan.h Add Pinescan and MultiSSID	2025-05-27 22:48:50 +01:00
amec0e	650fe84b4e	Update lang_var.h Added Pinescan and MultiSSID	2025-05-27 22:43:51 +01:00
Just Call Me Koko	2d922bac23	Merge pull request #763 from justcallmekoko/develop Fix SD delete not working on touch hardware	2025-05-19 13:38:14 -04:00
Just Call Me Koko	e918c939f0	Fix SD delete not working on touch hardware	2025-05-19 13:32:45 -04:00
Just Call Me Koko	a0c5349bea	Add images to detail BFFB NRF24 fix	2025-05-15 12:31:47 -04:00
Just Call Me Koko	f3224edccf	Merge pull request #749 from justcallmekoko/develop Fix touch screen menu buttons on non touch screen	2025-05-07 18:48:19 -04:00
Just Call Me Koko	9482a9dde2	Fix touch screen menu buttons on non touch screen	2025-05-07 18:44:23 -04:00
Just Call Me Koko	2afab2e414	Merge pull request #748 from justcallmekoko/develop	2025-05-07 17:19:32 -04:00
Just Call Me Koko	3b479be94c	Menu buttons delineated by brackets	2025-05-07 16:30:54 -04:00
Just Call Me Koko	c2fdb56200	Touch screen now has menu buttons	2025-05-06 23:47:23 -04:00
Just Call Me Koko	feebddff13	Merge pull request #746 from justcallmekoko/develop Increase Evil Portal HTML size limit for models with PSRAM and convert available memory to percentage	2025-05-06 13:35:20 -04:00
Just Call Me Koko	526b01e343	Fix null pointer	2025-05-06 13:30:37 -04:00
Just Call Me Koko	527414b3f4	Remove define	2025-05-06 13:05:06 -04:00
Just Call Me Koko	16a0e60471	Memory is shown as percentage Memory is shown as percentage in status bar. HTML and wardriving MACs are stored in PSRAM for available hardware	2025-05-06 13:04:41 -04:00
Just Call Me Koko	313206f369	Merge pull request #738 from justcallmekoko/develop Increase limits and efficiency when using PSRAM	2025-04-30 11:17:27 -04:00
Just Call Me Koko	ad1caa1c25	Increase limits and efficiency when using PSRAM	2025-04-30 11:11:37 -04:00
Just Call Me Koko	317af676ec	Merge pull request #737 from justcallmekoko/develop Expose AP name for evil portal	2025-04-30 09:02:21 -04:00
Just Call Me Koko	2b66c4f304	Oops all berries	2025-04-30 08:57:25 -04:00
Just Call Me Koko	80f817660f	Expose AP name for evil portal	2025-04-30 08:53:40 -04:00
Just Call Me Koko	fb6d1fa0a3	Merge pull request #736 from justcallmekoko/develop Port to CYD 2432S024 GUITION	2025-04-29 15:21:35 -04:00
Just Call Me Koko	f00906058a	Fix LED for CYD 2432S028	2025-04-29 15:15:51 -04:00
Just Call Me Koko	798fb3bbb7	Port to CYD 2432S024 GUITION	2025-04-29 14:29:34 -04:00
Just Call Me Koko	011d2c5f1b	Merge pull request #733 from justcallmekoko/develop Fix LVGL for CYD	2025-04-25 18:26:43 -04:00
Just Call Me Koko	cca589f749	Fix LVGL for CYD	2025-04-25 18:21:11 -04:00
Just Call Me Koko	68ef819383	Merge pull request #732 from justcallmekoko/develop Add build for CYD 2432S028	2025-04-25 17:50:23 -04:00
Just Call Me Koko	37290100e4	Add missing library for CYD	2025-04-25 17:46:36 -04:00
Just Call Me Koko	8eab6bff81	Add build for CYD 2432S028	2025-04-25 17:40:30 -04:00
Just Call Me Koko	4426f3778a	Merge pull request #731 from justcallmekoko/develop Port ESP32 Marauder to CYD 2432S028	2025-04-25 17:40:06 -04:00
Just Call Me Koko	4a90876d81	Port ESP32 Marauder to CYD 2432S028	2025-04-25 17:32:28 -04:00
Just Call Me Koko	9fd032a698	Merge pull request #724 from justcallmekoko/develop Channel analyzer graph scaling is more fluid	2025-04-19 14:04:42 -04:00
Just Call Me Koko	97dce525a4	Graph scaling more fluid	2025-04-19 13:46:31 -04:00
Just Call Me Koko	424aa61127	Merge pull request #722 from justcallmekoko/develop Channel analyzer graphs shows frames without multiplier	2025-04-19 13:45:42 -04:00
Just Call Me Koko	4c6a2b23c4	Fix graph scaling	2025-04-19 12:58:54 -04:00
Just Call Me Koko	10f90d93d8	Merge pull request #715 from justcallmekoko/develop Fix missing JSON for Load APs	2025-04-16 11:18:59 -04:00
Just Call Me Koko	51588497aa	Fix missing JSON for Load APs	2025-04-16 11:08:25 -04:00
Just Call Me Koko	4a0a3f5182	Merge pull request #714 from justcallmekoko/develop Add more stats to raw capture	2025-04-16 10:35:56 -04:00
Just Call Me Koko	8b84f4c19a	Add more stats to raw capture	2025-04-16 10:23:11 -04:00
Just Call Me Koko	74baf42dca	Merge pull request #713 from justcallmekoko/develop Add WPS and Manufacturer check for AP scan	2025-04-15 21:12:09 -04:00
Just Call Me Koko	983887191c	Add WPS and Manufacturer check for AP scan	2025-04-15 20:40:43 -04:00
Just Call Me Koko	046b396612	Merge pull request #711 from justcallmekoko/develop Add security check to AP scanning	2025-04-15 14:50:30 -04:00
Just Call Me Koko	86bec1e91a	Add security check to AP scanning	2025-04-15 14:24:19 -04:00
Just Call Me Koko	ae51c321ff	Merge pull request #710 from justcallmekoko/develop Fix packet count for non-display models	2025-04-15 11:56:21 -04:00
Just Call Me Koko	f3d9fbc2f8	Fix packet count not displaying for no screen models	2025-04-15 11:38:36 -04:00
Just Call Me Koko	1767f76362	Merge pull request #702 from justcallmekoko/develop Adjust conditions for MAC set errors	2025-04-10 11:40:56 -04:00
Just Call Me Koko	908aae7965	Adjust conditions for MAC set errors	2025-04-10 11:35:58 -04:00
Just Call Me Koko	4127e4d3d0	Merge pull request #700 from justcallmekoko/develop Make select -s all actually select all stations	2025-04-09 12:57:59 -04:00
Just Call Me Koko	cc4a069af3	Make select -s all actually select all	2025-04-09 12:52:10 -04:00
Just Call Me Koko	dae7e19abe	Merge pull request #699 from justcallmekoko/develop Fix evil portal AP name character limit	2025-04-09 12:48:05 -04:00
Just Call Me Koko	2a8006a59d	Fix evil portal AP name character limit	2025-04-09 12:28:26 -04:00
Just Call Me Koko	f0d1c048f5	Merge pull request #691 from justcallmekoko/develop Fix PSRAM crash issue with dual esp32 devices	2025-04-06 14:00:29 -04:00
Just Call Me Koko	94a7c6c587	Increment version number to v1.4.1	2025-04-06 13:52:52 -04:00
Just Call Me Koko	0a395944c6	Fix psram crash issue on dual ESP32 devices	2025-04-06 13:52:24 -04:00
Just Call Me Koko	00b27c8e87	Merge pull request #690 from justcallmekoko/develop Increment version number to v1.4.0	2025-04-04 16:17:33 -04:00
Just Call Me Koko	065e931376	Increment version number to v1.4.0	2025-04-04 16:11:50 -04:00
Just Call Me Koko	9b7d1ab31f	Merge pull request #689 from justcallmekoko/develop Get signal strength working on ILI9341 again	2025-04-04 16:11:08 -04:00
Just Call Me Koko	593dd99d1a	Fix non-display scanning	2025-04-04 16:06:28 -04:00
Just Call Me Koko	12794f57bc	Get signal strength working on ILI9341 again Allow channel scrolling on signal strength analyzer for ILI9341 devices	2025-04-04 15:49:14 -04:00
Just Call Me Koko	7c73689a13	Merge pull request #688 from justcallmekoko/develop Add channel analyzer to ILI9341 devices	2025-04-04 12:02:14 -04:00
Just Call Me Koko	20e70e9343	Add channel analyzer to ILI9341 devices	2025-04-04 11:55:45 -04:00
Just Call Me Koko	25567aca81	Merge pull request #687 from justcallmekoko/develop Add channel and exit buttons for ILI9341 to do raw capture	2025-04-04 11:39:09 -04:00
Just Call Me Koko	0ecc183b59	Remove button delay	2025-04-04 10:46:17 -04:00
Just Call Me Koko	df5e495f3a	ILI9431 can do sniff raw now	2025-04-04 10:44:04 -04:00
Just Call Me Koko	aa5cb56b97	Merge pull request #686 from justcallmekoko/develop Remove Scan AP and Scan Sta menu options from ILI9341 and replace with Scan All	2025-04-04 10:36:02 -04:00
Just Call Me Koko	cd5d537373	Actually remove scan ap from ILI9341	2025-04-04 10:29:26 -04:00
Just Call Me Koko	868c8a85de	Merge pull request #685 from justcallmekoko/develop Add clone STA MAC	2025-04-04 10:21:50 -04:00
Just Call Me Koko	d3299474c6	Remove scan ap and scan sta from ili9341 devices To save menu space, remove these because we have scan all now	2025-04-04 10:17:12 -04:00
Just Call Me Koko	e662f917bc	Start bringing features to ILI9341	2025-04-03 19:43:21 -04:00
Just Call Me Koko	4004e4e6d0	Add clone STA MAC	2025-04-03 14:47:37 -04:00
Just Call Me Koko	cdae54be5a	Merge pull request #684 from justcallmekoko/develop Add clone AP MAC	2025-04-03 14:19:03 -04:00
Just Call Me Koko	4dd856999f	Add clone AP MAC	2025-04-03 14:13:57 -04:00
Just Call Me Koko	231d331ff7	Merge pull request #683 from justcallmekoko/develop Add generate random MACs for AP and Station WiFi interface	2025-04-03 12:18:57 -04:00
Just Call Me Koko	1cc7b3f620	Fix printing for non screen models	2025-04-03 11:13:00 -04:00
Just Call Me Koko	caecd09d74	Create set macs menu and fix wifi init for macs	2025-04-03 10:57:01 -04:00
Just Call Me Koko	3c5b3bd544	Fix button icon color on scroll	2025-04-03 10:12:37 -04:00
Just Call Me Koko	4d145d5c0b	Set MACs before every wifi function	2025-04-02 22:11:28 -04:00
Just Call Me Koko	020d0ace3c	Get ready for setting new MACs	2025-04-02 16:35:28 -04:00
Just Call Me Koko	6229ad6d2a	Add commands for info and ap/station scanning	2025-04-02 15:39:30 -04:00
Just Call Me Koko	649f619f87	Merge pull request #682 from justcallmekoko/develop Fix EP HTML file menu	2025-04-02 11:00:29 -04:00
Just Call Me Koko	695aed1710	Fix EP HTML file menu	2025-04-02 10:27:25 -04:00
Just Call Me Koko	76dd3f020d	Merge pull request #681 from justcallmekoko/develop Make Raw Capture prioritize PCAP instead of display	2025-04-02 09:23:56 -04:00
Just Call Me Koko	60d8a9004b	Fix display buffer keys for no display	2025-04-01 21:46:24 -04:00
Just Call Me Koko	84fc9738d4	Merge pull request #680 from justcallmekoko/develop Add single scan for AP and Stations	2025-04-01 21:38:50 -04:00
Just Call Me Koko	ed65e6d2f7	Remove hardware def	2025-04-01 21:32:23 -04:00
Just Call Me Koko	fad44231cf	Add wifi scan ap sta	2025-04-01 21:30:58 -04:00
Just Call Me Koko	974ed246dc	Merge pull request #679 from justcallmekoko/develop Add AP info and reduce button array size	2025-04-01 19:08:59 -04:00
Just Call Me Koko	960c66247d	Fix AP info when no screen	2025-04-01 18:28:16 -04:00
Just Call Me Koko	39b53e22ba	Start at menu top on back button	2025-04-01 18:26:08 -04:00
Just Call Me Koko	1bc2b36c9c	Add AP info and reduce button array size	2025-04-01 18:13:02 -04:00
Just Call Me Koko	fe6ab68819	Merge pull request #678 from justcallmekoko/develop Add packet count function and fix signal monitor	2025-03-29 23:32:35 -04:00
Just Call Me Koko	f4634638a9	Add packet count command	2025-03-29 20:23:38 -04:00
Just Call Me Koko	e3f32106d9	Create packet rate monitor	2025-03-29 14:13:53 -04:00
Just Call Me Koko	1e5b083d14	Add OUI check to station sniff	2025-03-28 17:55:54 -04:00
Just Call Me Koko	46dafaa2e4	Merge pull request #677 from justcallmekoko/develop Add quick names to analyzer graphs	2025-03-27 14:25:26 -04:00
Just Call Me Koko	fab8088198	Clear board definitions	2025-03-27 13:57:48 -04:00
Just Call Me Koko	e16d421213	Add quick names to analyzer graph	2025-03-27 13:57:27 -04:00
Just Call Me Koko	3ba30ec5d9	Merge pull request #676 from justcallmekoko/master Merge master into develop	2025-03-26 10:43:20 -04:00