Merge pull request #781 from justcallmekoko/develop

Add build for CYD 2 USB

.github/workflows/build_parallel.yml

@@ -17,19 +17,23 @@ jobs:
       fail-fast: false
       matrix:
         board:
-          - { name: "Flipper Zero WiFi Dev Board",  flag: "MARAUDER_FLIPPER",         fbqn: "esp32:esp32:esp32s2:PartitionScheme=min_spiffs,FlashSize=4M,PSRAM=enabled",  file_name: "flipper",                 tft: false, tft_file: "",                                   build_dir: "esp32s2", addr: "0x1000" }
-          - { name: "Flipper Zero Multi Board",     flag: "MARAUDER_FLIPPER",         fbqn: "esp32:esp32:esp32s3:PartitionScheme=min_spiffs,FlashSize=8M,PSRAM=enabled",  file_name: "multiboardS3",            tft: false, tft_file: "",                                   build_dir: "esp32s3", addr: "0x0" }
-          - { name: "OG Marauder",                  flag: "MARAUDER_V4",              fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                 file_name: "og",                      tft: true,  tft_file: "User_Setup_og_marauder.h",           build_dir: "d32",     addr: "0x1000" }
-          - { name: "Marauder v6",                  flag: "MARAUDER_V6",              fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                 file_name: "v6",                      tft: true,  tft_file: "User_Setup_og_marauder.h",           build_dir: "d32",     addr: "0x1000" }
-          - { name: "Marauder v6.1",                flag: "MARAUDER_V6_1",            fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                 file_name: "v6_1",                    tft: true,  tft_file: "User_Setup_og_marauder.h",           build_dir: "d32",     addr: "0x1000" }
-          - { name: "Marauder Kit",                 flag: "MARAUDER_KIT",             fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                 file_name: "kit",                     tft: true,  tft_file: "User_Setup_og_marauder.h",           build_dir: "d32",     addr: "0x1000" }
-          - { name: "Marauder Mini",                flag: "MARAUDER_MINI",            fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                 file_name: "mini",                    tft: true,  tft_file: "User_Setup_marauder_mini.h",         build_dir: "d32",     addr: "0x1000" }
-          - { name: "ESP32 LDDB",                   flag: "ESP32_LDDB",               fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                 file_name: "esp32_lddb",              tft: false, tft_file: "",                                   build_dir: "d32",     addr: "0x1000" }
-          - { name: "Marauder Dev Board Pro",       flag: "MARAUDER_DEV_BOARD_PRO",   fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                 file_name: "marauder_dev_board_pro",  tft: false, tft_file: "",                                   build_dir: "d32",     addr: "0x1000" }
-          - { name: "M5StickCPlus",                 flag: "MARAUDER_M5STICKC",        fbqn: "esp32:esp32:m5stick-c:PartitionScheme=min_spiffs",                           file_name: "m5stickc_plus",           tft: true,  tft_file: "User_Setup_marauder_m5stickc.h",     build_dir: "m5stick-c", addr: "0x1000" }
-          - { name: "M5StickCPlus 2",               flag: "MARAUDER_M5STICKCP2",      fbqn: "esp32:esp32:m5stick-c:PartitionScheme=min_spiffs",                           file_name: "m5stickc_plus2",          tft: true,  tft_file: "User_Setup_marauder_m5stickcp2.h",   build_dir: "m5stick-c", addr: "0x1000" }
-          - { name: "Rev Feather",                  flag: "MARAUDER_REV_FEATHER",     fbqn: "esp32:esp32:esp32s2:PartitionScheme=min_spiffs,FlashSize=4M,PSRAM=enabled",  file_name: "rev_feather",             tft: true,  tft_file: "User_Setup_marauder_rev_feather.h",  build_dir: "esp32s2", addr: "0x1000" }
-          - { name: "Marauder v7",                  flag: "MARAUDER_V7",              fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                 file_name: "marauder_v7",             tft: true,  tft_file: "User_Setup_dual_nrf24.h",            build_dir: "d32",     addr: "0x1000" }
+          - { name: "Flipper Zero WiFi Dev Board",   flag: "MARAUDER_FLIPPER",         fbqn: "esp32:esp32:esp32s2:PartitionScheme=min_spiffs,FlashSize=4M,PSRAM=enabled",                     file_name: "flipper",                 tft: false, tft_file: "",                                   build_dir: "esp32s2",                    addr: "0x1000" }
+          - { name: "Flipper Zero Multi Board",      flag: "MARAUDER_FLIPPER",         fbqn: "esp32:esp32:esp32s3:PartitionScheme=min_spiffs,FlashSize=8M,PSRAM=enabled",                     file_name: "multiboardS3",            tft: false, tft_file: "",                                   build_dir: "esp32s3",                    addr: "0x0" }
+          - { name: "OG Marauder",                   flag: "MARAUDER_V4",              fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                                    file_name: "og",                      tft: true,  tft_file: "User_Setup_og_marauder.h",           build_dir: "d32",                        addr: "0x1000" }
+          - { name: "Marauder v6",                   flag: "MARAUDER_V6",              fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                                    file_name: "v6",                      tft: true,  tft_file: "User_Setup_og_marauder.h",           build_dir: "d32",                        addr: "0x1000" }
+          - { name: "Marauder v6.1",                 flag: "MARAUDER_V6_1",            fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                                    file_name: "v6_1",                    tft: true,  tft_file: "User_Setup_og_marauder.h",           build_dir: "d32",                        addr: "0x1000" }
+          - { name: "Marauder Kit",                  flag: "MARAUDER_KIT",             fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                                    file_name: "kit",                     tft: true,  tft_file: "User_Setup_og_marauder.h",           build_dir: "d32",                        addr: "0x1000" }
+          - { name: "Marauder Mini",                 flag: "MARAUDER_MINI",            fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                                    file_name: "mini",                    tft: true,  tft_file: "User_Setup_marauder_mini.h",         build_dir: "d32",                        addr: "0x1000" }
+          - { name: "ESP32 LDDB",                    flag: "ESP32_LDDB",               fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                                    file_name: "esp32_lddb",              tft: false, tft_file: "",                                   build_dir: "d32",                        addr: "0x1000" }
+          - { name: "Marauder Dev Board Pro",        flag: "MARAUDER_DEV_BOARD_PRO",   fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                                    file_name: "marauder_dev_board_pro",  tft: false, tft_file: "",                                   build_dir: "d32",                        addr: "0x1000" }
+          - { name: "M5StickCPlus",                  flag: "MARAUDER_M5STICKC",        fbqn: "esp32:esp32:m5stick-c:PartitionScheme=min_spiffs",                                              file_name: "m5stickc_plus",           tft: true,  tft_file: "User_Setup_marauder_m5stickc.h",     build_dir: "m5stick-c",                  addr: "0x1000" }
+          - { name: "M5StickCPlus 2",                flag: "MARAUDER_M5STICKCP2",      fbqn: "esp32:esp32:m5stick-c:PartitionScheme=min_spiffs",                                              file_name: "m5stickc_plus2",          tft: true,  tft_file: "User_Setup_marauder_m5stickcp2.h",   build_dir: "m5stick-c",                  addr: "0x1000" }
+          - { name: "Rev Feather",                   flag: "MARAUDER_REV_FEATHER",     fbqn: "esp32:esp32:esp32s2:PartitionScheme=min_spiffs,FlashSize=4M,PSRAM=enabled",                     file_name: "rev_feather",             tft: true,  tft_file: "User_Setup_marauder_rev_feather.h",  build_dir: "esp32s2",                    addr: "0x1000" }
+          - { name: "Marauder v7",                   flag: "MARAUDER_V7",              fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                                    file_name: "marauder_v7",             tft: true,  tft_file: "User_Setup_dual_nrf24.h",            build_dir: "d32",                        addr: "0x1000" }
+          - { name: "Marauder CYD 2432S028",         flag: "MARAUDER_CYD_MICRO",       fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                                    file_name: "cyd_2432S028",            tft: true,  tft_file: "User_Setup_cyd_micro.h",             build_dir: "d32",                        addr: "0x1000" }
+          - { name: "Marauder CYD 2432S024 GUITION", flag: "MARAUDER_CYD_GUITION",     fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                                    file_name: "cyd_2432S024_guition",    tft: true,  tft_file: "User_Setup_cyd_guition.h",           build_dir: "d32",                        addr: "0x1000" }
+          - { name: "Marauder CYD 2432S028 2 USB",   flag: "MARAUDER_CYD_2USB",        fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                                    file_name: "cyd_2432S028_2usb",       tft: true,  tft_file: "User_Setup_cyd_2usb.h",              build_dir: "d32",                        addr: "0x1000" }
+          - { name: "Marauder v7.1",                 flag: "MARAUDER_V7_1",            fbqn: "esp32:esp32:dfrobot_firebeetle2_esp32e:FlashSize=16M,PartitionScheme=min_spiffs,PSRAM=enabled", file_name: "marauder_v7_1",           tft: true,  tft_file: "User_Setup_dual_nrf24.h",            build_dir: "dfrobot_firebeetle2_esp32e", addr: "0x1000" }
           
     steps:
       - name: Checkout Code
@@ -92,6 +96,13 @@ jobs:
           repository: Bodmer/TFT_eSPI
           ref: V2.5.34
           path: CustomTFT_eSPI
+          
+      - name: Install XPT2046_Touchscreen
+        uses: actions/checkout@v2
+        with:
+          repository: PaulStoffregen/XPT2046_Touchscreen
+          ref: v1.4
+          path: CustomXPT2046_Touchscreen
 
       - name: Install lv_arduino
         uses: actions/checkout@v2

.github/workflows/build_push.yml

@@ -1,886 +0,0 @@
-name: Build and Push
-
-on:
-  workflow_dispatch:
-  pull_request:
-
-jobs:
-  # This workflow contains a single job called "build"
-  build:
-    name: Build Marauder Binaries
-    
-    runs-on: ubuntu-latest
-    
-    steps:
-      - name: Checkout Code
-        uses: actions/checkout@v3
-        
-#      - name: Install ESP32 Boards and Compile TestFile
-#        uses: ArminJo/arduino-test-compile@v3.2.1
-#        with:
-#          sketch-names: TestFile.ino
-#          arduino-board-fqbn: esp32:esp32:esp32s2
-#          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.10/package_esp32_dev_index.json
-          
-      - name: Install Arduino CLI
-        run: |
-          curl -fsSL https://raw.githubusercontent.com/arduino/arduino-cli/master/install.sh | sh
-          echo "/home/runner/work/ESP32Marauder/ESP32Marauder/bin" >> $GITHUB_PATH
-          export PATH=$PATH:/home/runner/work/ESP32Marauder/ESP32Marauder/bin
-          arduino-cli version
-
-      - name: Install Arduino-ESP32 Core v2.0.11
-        run: |
-          arduino-cli core update-index
-          arduino-cli core install esp32:esp32@2.0.11
-
-      - name: Verify Installed Cores
-        run: arduino-cli core list
-
-      - name: Build TestFile with ESP32 v2.0.11
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: TestFile.ino
-          arduino-board-fqbn: esp32:esp32:esp32s2
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-
-      - name: Verify Installed Cores Again
-        run: arduino-cli core list
-          
-      - name: Show Arduino dir structure
-        run: |
-          find /home/runner/.arduino15/packages/esp32/hardware/
-        
-#      - name: Pull arduino-esp32 v2.0.4
-#        uses: actions/checkout@v2
-#        with:
-#          repository: espressif/arduino-esp32
-#          ref: 2.0.4
-#          path: 2.0.4arduino-esp32
-          
-#      - name: Pull arduino-esp32 v2.0.10
-#        uses: actions/checkout@v2
-#        with:
-#          repository: espressif/arduino-esp32
-#          ref: 2.0.10
-#          path: 2.0.10
-          
-      - name: Install AsyncTCP
-        uses: actions/checkout@v2
-        with:
-          repository: me-no-dev/AsyncTCP
-          ref: master
-          path: CustomAsyncTCP
-          
-      - name: Install MicroNMEA
-        uses: actions/checkout@v2
-        with:
-          repository: stevemarple/MicroNMEA
-          ref: v2.0.6
-          path: CustomMicroNMEA
-          
-      - name: Install ESPAsyncWebServer
-        uses: actions/checkout@v2
-        with:
-          repository: bigbrodude6119/ESPAsyncWebServer
-          ref: master
-          path: CustomESPAsyncWebServer
-          
-      - name: Install TFT_eSPI
-        uses: actions/checkout@v2
-        with:
-          repository: Bodmer/TFT_eSPI
-          ref: V2.5.34
-          path: CustomTFT_eSPI
-
-      - name: Install lv_arduino
-        uses: actions/checkout@v2
-        with:
-          repository: lvgl/lv_arduino
-          ref: 3.0.0
-          path: Customlv_arduino
-
-      - name: Install JPEGDecoder
-        uses: actions/checkout@v2
-        with:
-          repository: Bodmer/JPEGDecoder
-          ref: 1.8.0
-          path: CustomJPEGDecoder
-
-      - name: Install NimBLE-Arduino
-        uses: actions/checkout@v2
-        with:
-          repository: h2zero/NimBLE-Arduino
-          ref: 1.3.5
-          path: CustomNimBLE-Arduino
-
-      - name: Install Adafruit_NeoPixel
-        uses: actions/checkout@v2
-        with:
-          repository: adafruit/Adafruit_NeoPixel
-          ref: 1.10.7
-          path: CustomAdafruit_NeoPixel
-
-      - name: Install ArduinoJson
-        uses: actions/checkout@v2
-        with:
-          repository: bblanchon/ArduinoJson
-          ref: v6.18.2
-          path: CustomArduinoJson
-
-      #- name: Install SwitchLib
-      #  uses: actions/checkout@v2
-      #  with:
-      #    repository: justcallmekoko/SwitchLib
-      #    ref: main
-      #    path: CustomSwitchLib
-          
-      - name: Install LinkedList
-        uses: actions/checkout@v2
-        with:
-          repository: ivanseidel/LinkedList
-          ref: v1.3.3
-          path: CustomLinkedList
-          
-      - name: Install EspSoftwareSerial
-        uses: actions/checkout@v2
-        with:
-          repository: plerup/espsoftwareserial
-          ref: 8.1.0
-          path: CustomEspSoftwareSerial
-          
-      - name: Install Adafruit_BusIO
-        uses: actions/checkout@v2
-        with:
-          repository: adafruit/Adafruit_BusIO
-          ref: 1.15.0
-          path: CustomAdafruit_BusIO
-          
-      - name: Install Adafruit_MAX1704X
-        uses: actions/checkout@v2
-        with:
-          repository: adafruit/Adafruit_MAX1704X
-          ref: 1.0.2
-          path: CustomAdafruit_MAX1704X
-          
-      #- name: Search for SD lib in arduino-esp32 v2.0.4
-      #  run: |
-      #    find /home/runner/work/ESP32Marauder/ESP32Marauder/2.0.4arduino-esp32 -name "SD"
-          
-      - name: Configure TFT_eSPI
-        run: |
-          rm -f CustomTFT_eSPI/User_Setup_Select.h
-          cp User_Setup_Select.h CustomTFT_eSPI/
-          cp User_Setup_marauder_mini.h CustomTFT_eSPI/
-          cp User_Setup_og_marauder.h CustomTFT_eSPI/
-          cp User_Setup_marauder_m5stickc.h CustomTFT_eSPI/
-          cp User_Setup_marauder_m5stickcp2.h CustomTFT_eSPI/
-          cp User_Setup_marauder_rev_feather.h CustomTFT_eSPI/
-          cp User_Setup_dual_nrf24.h CustomTFT_eSPI/
-          pwd
-          ls -la
-          ls -la CustomTFT_eSPI
-          
-      #- name: Place 2.0.10 for use
-      #  run: |
-      #    mkdir -p /home/runner/.arduino15/packages/esp32/hardware/esp32/
-      #    cp -R /home/runner/work/ESP32Marauder/ESP32Marauder/2.0.3 /home/runner/.arduino15/packages/esp32/hardware/esp32/2.0.3
-      #    ls -la /home/runner/.arduino15/packages/esp32/hardware/esp32/
-      #    echo Whoever made me have to do this can fuck off
-          
-      #- name: Replace arduino-esp32 v2.0.10 that was gloriously forced on us
-      #  run: |
-      #    rm -rf /home/runner/.arduino15/packages/esp32/hardware/esp32/2.0.10
-      #    cp -R /home/runner/work/ESP32Marauder/ESP32Marauder/2.0.3 /home/runner/.arduino15/packages/esp32/hardware/esp32/2.0.3
-      #    ls -la /home/runner/.arduino15/packages/esp32/hardware/esp32/
-      #    echo Whoever made me have to do this can fuck off
-          
-      #- name: Search for SD lib in arduino-esp32
-      #  run: |
-      #    find /home/runner/ -name "SD"
-          
-      #- name: Replace SD lib
-      #  run: |
-      #    rm -rf /home/runner/.arduino15/packages/esp32/hardware/esp32/2.0.10/libraries/SD
-      #    cp -R /home/runner/work/ESP32Marauder/ESP32Marauder/2.0.4arduino-esp32/libraries/SD /home/runner/.arduino15/packages/esp32/hardware/esp32/2.0.10/libraries/SD
-      #    ls -la /home/runner/.arduino15/packages/esp32/hardware/esp32/2.0.10/libraries/SD
-          
-      - name: Modify platform.txt
-        run: |
-          for i in $(find /home/runner/.arduino15/packages/esp32/hardware/esp32/ -name "platform.txt"); do
-            sed -i 's/compiler.c.elf.libs.esp32c3=/compiler.c.elf.libs.esp32c3=-zmuldefs /' "$i"
-            sed -i 's/compiler.c.elf.libs.esp32s3=/compiler.c.elf.libs.esp32s3=-zmuldefs /' "$i"
-            sed -i 's/compiler.c.elf.libs.esp32s2=/compiler.c.elf.libs.esp32s2=-zmuldefs /' "$i"
-            sed -i 's/compiler.c.elf.libs.esp32=/compiler.c.elf.libs.esp32=-zmuldefs /' "$i"
-            cat "$i" | grep compiler.c.elf.libs.esp32c3
-            cat "$i" | grep compiler.c.elf.libs.esp32s3
-            cat "$i" | grep compiler.c.elf.libs.esp32s2
-            cat "$i" | grep compiler.c.elf.libs.esp32
-          done
-          
-      - name: Configure configs.h for Flipper Zero WiFi Dev Board
-        run: |
-          sed -i 's/^  #define MARAUDER_REV_FEATHER/  \/\/#define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_M5STICKC/  \/\/#define MARAUDER_M5STICKC/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_MINI/  \/\/#define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V4/  \/\/#define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6/  \/\/#define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6_1/  \/\/#define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V7/  \/\/#define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_KIT/  \/\/#define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  \/\/#define MARAUDER_FLIPPER/  #define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  #define ESP32_LDDB/  \/\/#define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_DEV_BOARD_PRO/  \/\/#define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-                    
-      - name: Build Marauder for Flipper Zero WiFi Dev Board
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:esp32s2:PartitionScheme=min_spiffs,FlashSize=4M,PSRAM=enabled
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename Marauder Flipper bin
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.esp32s2/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.esp32s2/esp32_marauder.flipper.bin
-          
-      - name: Build Marauder for Flipper Zero Multi Board
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:esp32s3:PartitionScheme=min_spiffs,FlashSize=8M,PSRAM=enabled
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename Marauder Multi Board bin
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.esp32s3/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.esp32s3/esp32_marauder.multiboardS3.bin
-         
-      - name: Configure TFT_eSPI and configs.h for OG Marauder
-        run: |
-          pwd
-          find /home/runner/ -name "*TFT_eSPI*"     
-          sed -i 's/^#include <User_Setup_marauder_rev_feather.h>/\/\/#include <User_Setup_marauder_rev_feather.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h          
-          sed -i 's/^#include <User_Setup_marauder_mini.h>/\/\/#include <User_Setup_marauder_mini.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_marauder_m5stickc.h>/\/\/#include <User_Setup_marauder_m5stickc.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_dual_nrf24.h>/\/\/#include <User_Setup_dual_nrf24.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^\/\/#include <User_Setup_og_marauder.h>/#include <User_Setup_og_marauder.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^  #define MARAUDER_REV_FEATHER/  \/\/#define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_MINI/  \/\/#define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  \/\/#define MARAUDER_V4/  #define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6/  \/\/#define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6_1/  \/\/#define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V7/  \/\/#define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_KIT/  \/\/#define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_FLIPPER/  \/\/#define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  #define ESP32_LDDB/  \/\/#define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_DEV_BOARD_PRO/  \/\/#define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-          
-      - name: Build Marauder for OG Marauder
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:d32:PartitionScheme=min_spiffs
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename OG Marauder bin
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.og.bin
-          
-      - name: Configure TFT_eSPI and configs.h for Marauder v6
-        run: |
-          sed -i 's/^#include <User_Setup_marauder_rev_feather.h>/\/\/#include <User_Setup_marauder_rev_feather.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_marauder_mini.h>/\/\/#include <User_Setup_marauder_mini.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_marauder_m5stickc.h>/\/\/#include <User_Setup_marauder_m5stickc.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_dual_nrf24.h>/\/\/#include <User_Setup_dual_nrf24.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^\/\/#include <User_Setup_og_marauder.h>/#include <User_Setup_og_marauder.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^  #define MARAUDER_REV_FEATHER/  \/\/#define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_MINI/  \/\/#define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V4/  \/\/#define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  \/\/#define MARAUDER_V6/  #define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6_1/  \/\/#define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V7/  \/\/#define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_KIT/  \/\/#define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_FLIPPER/  \/\/#define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  #define ESP32_LDDB/  \/\/#define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_DEV_BOARD_PRO/  \/\/#define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-          
-      #- name: Build Marauder for v6 Marauder with arduino/compile-sketches
-      #  uses: arduino/compile-sketches@v1
-      #  with:
-      #    sketch-paths: esp32_marauder/esp32_marauder.ino
-      #    cli-compile-flags: |
-      #      - --warnings="none"
-      #      - --export-binaries
-      #    fqbn: esp32:esp32:d32:PartitionScheme=min_spiffs
-          
-      #- name: Show compiled arduino/compile-sketches v6 bin
-      #  run: |
-      #    find ~ -name "esp32_marauder.ino.bin"
-          
-      #- name: Rename v6_2 Marauder bin
-      #  run: |
-      #    mv ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.v6_2.bin
-          
-      - name: Build Marauder for v6 Marauder
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:d32:PartitionScheme=min_spiffs
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename v6 Marauder bin
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.v6.bin
-          
-      - name: Configure TFT_eSPI and configs.h for Marauder v6.1
-        run: |
-          sed -i 's/^  #define MARAUDER_REV_FEATHER/  \/\/#define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_MINI/  \/\/#define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V4/  \/\/#define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6/  \/\/#define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  \/\/#define MARAUDER_V6_1/  #define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V7/  \/\/#define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_KIT/  \/\/#define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_FLIPPER/  \/\/#define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  #define ESP32_LDDB/  \/\/#define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_DEV_BOARD_PRO/  \/\/#define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-          
-      - name: Build Marauder for v6.1 Marauder
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:d32:PartitionScheme=min_spiffs
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename v6 Marauder bin
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.v6_1.bin
-         
-      - name: Configure TFT_eSPI and configs.h for Marauder Kit
-        run: |
-          sed -i 's/^#include <User_Setup_marauder_mini.h>/\/\/#include <User_Setup_marauder_mini.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_marauder_m5stickc.h>/\/\/#include <User_Setup_marauder_m5stickc.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_dual_nrf24.h>/\/\/#include <User_Setup_dual_nrf24.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^\/\/#include <User_Setup_og_marauder.h>/#include <User_Setup_og_marauder.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^  #define MARAUDER_REV_FEATHER/  \/\/#define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_MINI/  \/\/#define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V4/  \/\/#define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6/  \/\/#define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6_1/  \/\/#define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V7/  \/\/#define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  \/\/#define MARAUDER_KIT/  #define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_FLIPPER/  \/\/#define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  #define ESP32_LDDB/  \/\/#define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_DEV_BOARD_PRO/  \/\/#define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-          
-      - name: Build Marauder for Marauder Kit
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:d32:PartitionScheme=min_spiffs
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename Marauder Kit bin
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.kit.bin
-          
-      - name: Configure TFT_eSPI and configs.h for Marauder Mini
-        run: |
-          sed -i 's/^\/\/#include <User_Setup_marauder_mini.h>/#include <User_Setup_marauder_mini.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_og_marauder.h>/\/\/#include <User_Setup_og_marauder.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_marauder_m5stickc.h>/\/\/#include <User_Setup_marauder_m5stickc.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_dual_nrf24.h>/\/\/#include <User_Setup_dual_nrf24.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^  #define MARAUDER_REV_FEATHER/  \/\/#define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  \/\/#define MARAUDER_MINI/  #define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V4/  \/\/#define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6/  \/\/#define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6_1/  \/\/#define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V7/  \/\/#define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_KIT/  \/\/#define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_FLIPPER/  \/\/#define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  #define ESP32_LDDB/  \/\/#define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_DEV_BOARD_PRO/  \/\/#define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-          
-      - name: Build Marauder for Marauder Mini
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:d32:PartitionScheme=min_spiffs
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename Marauder Mini bin
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.mini.bin
-          
-      - name: Configure TFT_eSPI and configs.h for ESP32 LDDB
-        run: |
-          sed -i 's/^  #define MARAUDER_REV_FEATHER/  \/\/#define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_MINI/  \/\/#define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V4/  \/\/#define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6/  \/\/#define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6_1/  \/\/#define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V7/  \/\/#define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_KIT/  \/\/#define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_FLIPPER/  \/\/#define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  \/\/#define ESP32_LDDB/  #define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_DEV_BOARD_PRO/  \/\/#define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-          
-      - name: Build Marauder for ESP32 LDDB
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:d32:PartitionScheme=min_spiffs
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename Marauder ESP32 LDDB bin
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.esp32_lddb.bin
-
-      - name: Configure TFT_eSPI and configs.h for Marauder Dev Board Pro
-        run: |
-          sed -i 's/^  #define MARAUDER_REV_FEATHER/  \/\/#define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_MINI/  \/\/#define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V4/  \/\/#define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6/  \/\/#define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6_1/  \/\/#define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V7/  \/\/#define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_KIT/  \/\/#define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_FLIPPER/  \/\/#define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  #define ESP32_LDDB/  \/\/#define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  \/\/#define MARAUDER_DEV_BOARD_PRO/  #define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-          
-      - name: Build Marauder for Marauder Dev Board Pro
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:d32:PartitionScheme=min_spiffs
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename Marauder for Marauder Dev Board Pro
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.marauder_dev_board_pro.bin
-          
-      - name: Configure TFT_eSPI and configs.h for Marauder M5StickC
-        run: |
-          pwd
-          find /home/runner/ -name "*TFT_eSPI*"          
-          sed -i 's/^#include <User_Setup_marauder_mini.h>/\/\/#include <User_Setup_marauder_mini.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^\/\/#include <User_Setup_marauder_m5stickc.h>/#include <User_Setup_marauder_m5stickc.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^  #define MARAUDER_REV_FEATHER/  \/\/#define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_MINI/  \/\/#define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V4/  \/\/#define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6/  \/\/#define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6_1/  \/\/#define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V7/  \/\/#define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_KIT/  \/\/#define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_FLIPPER/  \/\/#define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  #define ESP32_LDDB/  \/\/#define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_DEV_BOARD_PRO/  \/\/#define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-          sed -i 's/^  \/\/#define MARAUDER_M5STICKC /  #define MARAUDER_M5STICKC /' esp32_marauder/configs.h
-          
-      - name: Build Marauder for Marauder M5StickC
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:m5stick-c:PartitionScheme=min_spiffs
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename Marauder M5StickC bin
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.m5stick-c/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.m5stick-c/esp32_marauder.m5stickc_plus.bin
-
-      - name: Configure TFT_eSPI and configs.h for Marauder M5StickCP2
-        run: |
-          pwd
-          find /home/runner/ -name "*TFT_eSPI*"          
-          sed -i 's/^#include <User_Setup_marauder_mini.h>/\/\/#include <User_Setup_marauder_mini.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_marauder_m5stickc.h>/\/\/#include <User_Setup_marauder_m5stickc.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^\/\/#include <User_Setup_marauder_m5stickcp2.h>/#include <User_Setup_marauder_m5stickcp2.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^  #define MARAUDER_REV_FEATHER/  \/\/#define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_MINI/  \/\/#define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V4/  \/\/#define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6/  \/\/#define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6_1/  \/\/#define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V7/  \/\/#define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_KIT/  \/\/#define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_FLIPPER/  \/\/#define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  #define ESP32_LDDB/  \/\/#define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_DEV_BOARD_PRO/  \/\/#define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_M5STICKC /  \/\/#define MARAUDER_M5STICKC /' esp32_marauder/configs.h
-          sed -i 's/^  \/\/#define MARAUDER_M5STICKCP2/  #define MARAUDER_M5STICKCP2/' esp32_marauder/configs.h
-          
-      - name: Build Marauder for Marauder M5StickCP2
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:m5stick-c:PartitionScheme=min_spiffs
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename Marauder M5StickCP2 bin
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.m5stick-c/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.m5stick-c/esp32_marauder.m5stickc_plus2.bin
-
-      - name: Configure TFT_eSPI and configs.h for Marauder Rev Feather
-        run: |
-          pwd
-          find /home/runner/ -name "*TFT_eSPI*"          
-          sed -i 's/^\/\/#include <User_Setup_marauder_rev_feather.h>/#include <User_Setup_marauder_rev_feather.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_marauder_mini.h>/\/\/#include <User_Setup_marauder_mini.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_marauder_m5stickc.h>/\/\/#include <User_Setup_marauder_m5stickc.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_marauder_m5stickcp2.h>/\/\/#include <User_Setup_marauder_m5stickcp2.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^  \/\/#define MARAUDER_REV_FEATHER/  #define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_MINI/  \/\/#define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V4/  \/\/#define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6/  \/\/#define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6_1/  \/\/#define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V7/  \/\/#define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_KIT/  \/\/#define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_FLIPPER/  \/\/#define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  #define ESP32_LDDB/  \/\/#define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_DEV_BOARD_PRO/  \/\/#define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_M5STICKC /  \/\/#define MARAUDER_M5STICKC /' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_M5STICKCP2/  \/\/#define MARAUDER_M5STICKCP2/' esp32_marauder/configs.h
-          
-      - name: Build Marauder for Marauder Rev Feather
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:esp32s2:PartitionScheme=min_spiffs,FlashSize=4M,PSRAM=enabled
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename Marauder Marauder Rev Feather
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.esp32s2/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.esp32s2/esp32_marauder.rev_feather.bin
-          
-      - name: Configure TFT_eSPI and configs.h for Marauder v7
-        run: |
-          pwd
-          find /home/runner/ -name "*TFT_eSPI*"          
-          sed -i 's/^#include <User_Setup_marauder_rev_feather.h>/\/\/#include <User_Setup_marauder_rev_feather.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_marauder_mini.h>/\/\/#include <User_Setup_marauder_mini.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_marauder_m5stickc.h>/\/\/#include <User_Setup_marauder_m5stickc.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^\/\/#include <User_Setup_dual_nrf24.h>/#include <User_Setup_dual_nrf24.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^  #define MARAUDER_REV_FEATHER/  \/\/#define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_MINI/  \/\/#define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V4/  \/\/#define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6/  \/\/#define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6_1/  \/\/#define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  \/\/#define MARAUDER_V7/  #define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_KIT/  \/\/#define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_FLIPPER/  \/\/#define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  #define ESP32_LDDB/  \/\/#define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_DEV_BOARD_PRO/  \/\/#define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_M5STICKC/  \/\/#define MARAUDER_M5STICKC/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_M5STICKCP2/  \/\/#define MARAUDER_M5STICKCP2/' esp32_marauder/configs.h
-          
-      - name: Build Marauder for Marauder v7
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:d32:PartitionScheme=min_spiffs
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename Marauder Marauder v7
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.marauder_v7.bin
-
-      - name: Display finished bins
-        run: |
-          find ./esp32_marauder/build -name "*.bin"
-          
-      - name: 'Upload Flipper Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.flipper.bin
-          path: ./esp32_marauder/build/esp32.esp32.esp32s2/esp32_marauder.flipper.bin
-          retention-days: 5
-          
-      - name: 'Upload MultiboardS3 Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.multiboardS3.bin
-          path: ./esp32_marauder/build/esp32.esp32.esp32s3/esp32_marauder.multiboardS3.bin
-          retention-days: 5
-          
-      - name: 'Upload OG Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.og.bin
-          path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.og.bin
-          retention-days: 5
-          
-      - name: 'Upload v6 Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.v6.bin
-          path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.v6.bin
-          retention-days: 5
-          
-      - name: 'Upload v6_1 Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.v6_1.bin
-          path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.v6_1.bin
-          retention-days: 5
-          
-      - name: 'Upload Kit Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.kit.bin
-          path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.kit.bin
-          retention-days: 5
-          
-      - name: 'Upload Mini Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.mini.bin
-          path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.mini.bin
-          retention-days: 5
-          
-      - name: 'Upload ESP32 LDDB Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.esp32_lddb.bin
-          path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.esp32_lddb.bin
-          retention-days: 5
-          
-      - name: 'Upload Marauder Dev Board Pro Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.marauder_dev_board_pro.bin
-          path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.marauder_dev_board_pro.bin
-          retention-days: 5
-          
-      - name: 'Upload Marauder M5StickC Plus Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.m5stickc_plus.bin
-          path: ./esp32_marauder/build/esp32.esp32.m5stick-c/esp32_marauder.m5stickc_plus.bin
-          retention-days: 5
-
-      - name: 'Upload Marauder M5StickC Plus 2 Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.m5stickc_plus2.bin
-          path: ./esp32_marauder/build/esp32.esp32.m5stick-c/esp32_marauder.m5stickc_plus2.bin
-          retention-days: 5
-          
-      - name: 'Upload Rev Feather Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.rev_feather.bin
-          path: ./esp32_marauder/build/esp32.esp32.esp32s2/esp32_marauder.rev_feather.bin
-          retention-days: 5
-          
-      - name: 'Upload Marauder v7 Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.marauder_v7.bin
-          path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.marauder_v7.bin
-          retention-days: 5
-          
-      - name: Create Release
-        id: create_release
-        uses: actions/create-release@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          tag_name: ${{ github.ref }}
-          release_name: Release ${{ github.ref }}
-          draft: true
-          prerelease: false
-        if: github.event_name != 'pull_request'
-          
-      - name: Upload Flipper Asset
-        id: upload-flipper-release-asset 
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.esp32s2/esp32_marauder.flipper.bin
-          asset_name: esp32_marauder.flipper.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-          
-      - name: Upload MultiboardS3 Asset
-        id: upload-multiboardS3-release-asset 
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.esp32s3/esp32_marauder.multiboardS3.bin
-          asset_name: esp32_marauder.multiboardS3.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-          
-      - name: Upload OG Asset
-        id: upload-og-release-asset 
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.og.bin
-          asset_name: esp32_marauder.og.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-          
-      - name: Upload v6 Asset
-        id: upload-v6-release-asset 
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.v6.bin
-          asset_name: esp32_marauder.v6.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-        
-      - name: Upload v6_1 Asset
-        id: upload-v6-1-release-asset 
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.v6_1.bin
-          asset_name: esp32_marauder.v6_1.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-          
-      - name: Upload Kit Asset
-        id: upload-kit-release-asset 
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.kit.bin
-          asset_name: esp32_marauder.kit.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-          
-      - name: Upload Mini Asset
-        id: upload-mini-release-asset 
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.mini.bin
-          asset_name: esp32_marauder.mini.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-          
-      - name: Upload ESP32 LDDB Asset
-        id: upload-esp32-lddb-release-asset 
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.esp32_lddb.bin
-          asset_name: esp32_marauder.esp32_lddb.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-          
-      - name: Upload Marauder Dev Board Pro Asset
-        id: upload-marauder-dev-board-pro-release-asset
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.marauder_dev_board_pro.bin
-          asset_name: esp32_marauder.marauder_dev_board_pro.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-        
-      - name: Upload Marauder M5StickC Plus Asset
-        id: upload-m5stickc-plus-release-asset 
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.m5stick-c/esp32_marauder.m5stickc_plus.bin
-          asset_name: esp32_marauder.m5stickc_plus.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-
-      - name: Upload Marauder M5StickC Plus 2 Asset
-        id: upload-m5stickc-plus2-release-asset 
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.m5stick-c/esp32_marauder.m5stickc_plus2.bin
-          asset_name: esp32_marauder.m5stickc_plus2.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-
-      - name: Upload Rev Feather Asset
-        id: upload-rev-feather-release-asset 
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.esp32s2/esp32_marauder.rev_feather.bin
-          asset_name: esp32_marauder.rev_feather.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-        
-      - name: Upload Marauder v7 Asset
-        id: upload-marauder-v7-release-asset
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.marauder_v7.bin
-          asset_name: esp32_marauder.marauder_v7.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'

README.md

@@ -4,7 +4,7 @@
 <!---Shields/Badges https://shields.io/--->
 
 # ESP32 Marauder
-<p align="center"><img alt="Marauder logo" src="https://github.com/justcallmekoko/ESP32Marauder/blob/master/pictures/marauder3L.jpg?raw=true" width="300"></p>
+<p align="center"><img alt="Marauder logo" src="https://github.com/justcallmekoko/ESP32Marauder/blob/master/pictures/marauder_skull_patch_04_full_final.png?raw=true" width="300"></p>
 <p align="center">
   <b>A suite of WiFi/Bluetooth offensive and defensive tools for the ESP32</b>
   <br><br>

User_Setup_Select.h

@@ -28,8 +28,11 @@
 //#include <User_Setup_marauder_m5stickc.h>
 //#include <User_Setup_marauder_m5stickcp2.h>
 //#include <User_Setup_pocket_sdr.h>
-//#include <User_Setup_dual_nrf24.h>
-//#include <User_Setup_pocket_sdr_2.h>
+//#include <User_Setup_dual_nrf24.h> // Marauder v7
+//#include <User_Setup_pocket_sdr_2.h> // Drone Signal Analyzer
+//#include <User_Setup_cyd_micro.h>
+//#include <User_Setup_cyd_guition.h>
+#include <User_Setup_cyd_2usb.h>
 
 //#include <User_Setups/Setup1_ILI9341.h>  // Setup file configured for my ILI9341
 //#include <User_Setups/Setup2_ST7735.h>   // Setup file configured for my ST7735

User_Setup_cyd_2usb.h

@@ -0,0 +1,316 @@
+//                            USER DEFINED SETTINGS
+//   Set driver type, fonts to be loaded, pins used and SPI control method etc
+//
+//   See the User_Setup_Select.h file if you wish to be able to define multiple
+//   setups and then easily select which setup file is used by the compiler.
+//
+//   If this file is edited correctly then all the library example sketches should
+//   run without the need to make any more changes for a particular hardware setup!
+//   Note that some sketches are designed for a particular TFT pixel width/height
+
+
+// ##################################################################################
+//
+// Section 1. Call up the right driver file and any options for it
+//
+// ##################################################################################
+
+// Display type -  only define if RPi display
+//#define RPI_DRIVER
+
+// Only define one driver, the other ones must be commented out
+//#define ILI9341_DRIVER // OG Marauder
+//#define ST7735_DRIVER    // Marauder Mini  // Define additional parameters below for this display
+//#define ILI9163_DRIVER     // Define additional parameters below for this display
+//#define S6D02A1_DRIVER
+//#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
+//#define HX8357D_DRIVER
+//#define ILI9481_DRIVER
+//#define ILI9486_DRIVER
+//#define ILI9488_DRIVER     // WARNING: Do not connect ILI9488 display SDO to MISO if other devices share the SPI bus (TFT SDO does NOT tristate when CS is high)
+#define ST7789_DRIVER      // Full configuration option, define additional parameters below for this display
+//#define ST7789_2_DRIVER    // Minimal configuration option, define additional parameters below for this display
+//#define R61581_DRIVER
+//#define RM68140_DRIVER
+//#define ST7796_DRIVER
+
+// Some displays support SPI reads via the MISO pin, other displays have a single
+// bi-directional SDA pin and the library will try to read this via the MOSI line.
+// To use the SDA line for reading data from the TFT uncomment the following line:
+
+// #define TFT_SDA_READ      // This option is for ESP32 ONLY, tested with ST7789 display only
+
+// For ST7789 and ILI9341 ONLY, define the colour order IF the blue and red are swapped on your display
+// Try ONE option at a time to find the correct colour order for your display
+
+//  #define TFT_RGB_ORDER TFT_RGB  // Colour order Red-Green-Blue
+  #define TFT_RGB_ORDER TFT_BGR  // Colour order Blue-Green-Red
+
+// For M5Stack ESP32 module with integrated ILI9341 display ONLY, remove // in line below
+
+// #define M5STACK
+
+// For ST7789, ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation
+// #define TFT_WIDTH  80
+// #define TFT_WIDTH  128 // Marauder Mini
+ #define TFT_WIDTH  240 // ST7789 240 x 240 and 240 x 320
+// #define TFT_HEIGHT 160
+// #define TFT_HEIGHT 128 // Marauder Mini
+// #define TFT_HEIGHT 240 // ST7789 240 x 240
+ #define TFT_HEIGHT 320 // ST7789 240 x 320
+
+// For ST7735 ONLY, define the type of display, originally this was based on the
+// colour of the tab on the screen protector film but this is not always true, so try
+// out the different options below if the screen does not display graphics correctly,
+// e.g. colours wrong, mirror images, or tray pixels at the edges.
+// Comment out ALL BUT ONE of these options for a ST7735 display driver, save this
+// this User_Setup file, then rebuild and upload the sketch to the board again:
+
+// #define ST7735_INITB
+// #define ST7735_GREENTAB
+// #define ST7735_GREENTAB2
+// #define ST7735_GREENTAB3
+// #define ST7735_GREENTAB128    // For 128 x 128 display
+// #define ST7735_GREENTAB160x80 // For 160 x 80 display (BGR, inverted, 26 offset)
+// #define ST7735_REDTAB
+// #define ST7735_BLACKTAB
+// #define ST7735_REDTAB160x80   // For 160 x 80 display with 24 pixel offset
+
+// If colours are inverted (white shows as black) then uncomment one of the next
+// 2 lines try both options, one of the options should correct the inversion.
+
+// #define TFT_INVERSION_ON
+ #define TFT_INVERSION_OFF
+
+// If a backlight control signal is available then define the TFT_BL pin in Section 2
+// below. The backlight will be turned ON when tft.begin() is called, but the library
+// needs to know if the LEDs are ON with the pin HIGH or LOW. If the LEDs are to be
+// driven with a PWM signal or turned OFF/ON then this must be handled by the user
+// sketch. e.g. with digitalWrite(TFT_BL, LOW);
+
+// #define TFT_BACKLIGHT_ON LOW  // HIGH or LOW are options
+
+// ##################################################################################
+//
+// Section 2. Define the pins that are used to interface with the display here
+//
+// ##################################################################################
+
+// We must use hardware SPI, a minimum of 3 GPIO pins is needed.
+// Typical setup for ESP8266 NodeMCU ESP-12 is :
+//
+// Display SDO/MISO  to NodeMCU pin D6 (or leave disconnected if not reading TFT)
+// Display LED       to NodeMCU pin VIN (or 5V, see below)
+// Display SCK       to NodeMCU pin D5
+// Display SDI/MOSI  to NodeMCU pin D7
+// Display DC (RS/AO)to NodeMCU pin D3
+// Display RESET     to NodeMCU pin D4 (or RST, see below)
+// Display CS        to NodeMCU pin D8 (or GND, see below)
+// Display GND       to NodeMCU pin GND (0V)
+// Display VCC       to NodeMCU 5V or 3.3V
+//
+// The TFT RESET pin can be connected to the NodeMCU RST pin or 3.3V to free up a control pin
+//
+// The DC (Data Command) pin may be labeled AO or RS (Register Select)
+//
+// With some displays such as the ILI9341 the TFT CS pin can be connected to GND if no more
+// SPI devices (e.g. an SD Card) are connected, in this case comment out the #define TFT_CS
+// line below so it is NOT defined. Other displays such at the ST7735 require the TFT CS pin
+// to be toggled during setup, so in these cases the TFT_CS line must be defined and connected.
+//
+// The NodeMCU D0 pin can be used for RST
+//
+//
+// Note: only some versions of the NodeMCU provide the USB 5V on the VIN pin
+// If 5V is not available at a pin you can use 3.3V but backlight brightness
+// will be lower.
+
+
+// ###### EDIT THE PIN NUMBERS IN THE LINES FOLLOWING TO SUIT YOUR ESP8266 SETUP ######
+
+// For NodeMCU - use pin numbers in the form PIN_Dx where Dx is the NodeMCU pin designation
+//#define TFT_CS   PIN_D8  // Chip select control pin D8
+//#define TFT_DC   PIN_D3  // Data Command control pin
+//#define TFT_RST  PIN_D4  // Reset pin (could connect to NodeMCU RST, see next line)
+//#define TFT_RST  -1    // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
+
+//#define TFT_BL PIN_D1  // LED back-light (only for ST7789 with backlight control pin)
+
+//#define TOUCH_CS PIN_D2     // Chip select pin (T_CS) of touch screen
+
+//#define TFT_WR PIN_D2       // Write strobe for modified Raspberry Pi TFT only
+
+
+// ######  FOR ESP8266 OVERLAP MODE EDIT THE PIN NUMBERS IN THE FOLLOWING LINES  ######
+
+// Overlap mode shares the ESP8266 FLASH SPI bus with the TFT so has a performance impact
+// but saves pins for other functions. It is best not to connect MISO as some displays
+// do not tristate that line wjen chip select is high!
+// On NodeMCU 1.0 SD0=MISO, SD1=MOSI, CLK=SCLK to connect to TFT in overlap mode
+// On NodeMCU V3  S0 =MISO, S1 =MOSI, S2 =SCLK
+// In ESP8266 overlap mode the following must be defined
+
+//#define TFT_SPI_OVERLAP
+
+// In ESP8266 overlap mode the TFT chip select MUST connect to pin D3
+//#define TFT_CS   PIN_D3
+//#define TFT_DC   PIN_D5  // Data Command control pin
+//#define TFT_RST  PIN_D4  // Reset pin (could connect to NodeMCU RST, see next line)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
+
+
+// ###### EDIT THE PIN NUMBERS IN THE LINES FOLLOWING TO SUIT YOUR ESP32 SETUP   ######
+
+// For ESP32 Dev board (only tested with ILI9341 display)
+// The hardware SPI can be mapped to any pins
+
+// Marauder Mini
+/*
+#define TFT_CS   17  // Chip select control pin D8
+#define TFT_DC   16  // Data Command control pin
+#define TFT_RST  5  // Reset pin (could connect to NodeMCU RST, see next line)
+//#define TFT_MISO 19
+//#define TFT_MOSI 23
+//#define TFT_SCLK 18
+//#define TFT_BL   32
+*/
+
+// ESP32 Marauder 
+#define TFT_MISO 12
+#define TFT_MOSI 13
+#define TFT_SCLK 14
+#define TFT_CS   15  // Chip select control pin
+#define TFT_DC   2  // Data Command control pin
+#define TFT_RST   -1  // Reset pin (could connect to RST pin)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if display RESET is connected to ESP32 board RST
+
+#define TFT_BL   21  // LED back-light (only for ST7789 with backlight control pin)
+
+#define TOUCH_CS   33     // Chip select pin (T_CS) of touch screen
+
+/////////////////////////////
+
+// ESP32 Centauri
+/*
+#define TFT_MISO 19
+#define TFT_MOSI 23
+#define TFT_SCLK 18
+#define TFT_CS   27  // Chip select control pin
+#define TFT_DC   26  // Data Command control pin
+#define TFT_RST   5  // Reset pin (could connect to RST pin)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if display RESET is connected to ESP32 board RST
+
+#define TFT_BL   32  // LED back-light (only for ST7789 with backlight control pin)
+
+#define TOUCH_CS 21     // Chip select pin (T_CS) of touch screen
+*/
+/////////////////////////////
+
+//#define TFT_WR 22    // Write strobe for modified Raspberry Pi TFT only
+
+// For the M5Stack module use these #define lines
+//#define TFT_MISO 19
+//#define TFT_MOSI 23
+//#define TFT_SCLK 18
+//#define TFT_CS   14  // Chip select control pin
+//#define TFT_DC   27  // Data Command control pin
+//#define TFT_RST  33  // Reset pin (could connect to Arduino RESET pin)
+//#define TFT_BL   32  // LED back-light (required for M5Stack)
+
+// ######       EDIT THE PINs BELOW TO SUIT YOUR ESP32 PARALLEL TFT SETUP        ######
+
+// The library supports 8 bit parallel TFTs with the ESP32, the pin
+// selection below is compatible with ESP32 boards in UNO format.
+// Wemos D32 boards need to be modified, see diagram in Tools folder.
+// Only ILI9481 and ILI9341 based displays have been tested!
+
+// Parallel bus is only supported on ESP32
+// Uncomment line below to use ESP32 Parallel interface instead of SPI
+
+//#define ESP32_PARALLEL
+
+// The ESP32 and TFT the pins used for testing are:
+//#define TFT_CS   33  // Chip select control pin (library pulls permanently low
+//#define TFT_DC   15  // Data Command control pin - must use a pin in the range 0-31
+//#define TFT_RST  32  // Reset pin, toggles on startup
+
+//#define TFT_WR    4  // Write strobe control pin - must use a pin in the range 0-31
+//#define TFT_RD    2  // Read strobe control pin
+
+//#define TFT_D0   12  // Must use pins in the range 0-31 for the data bus
+//#define TFT_D1   13  // so a single register write sets/clears all bits.
+//#define TFT_D2   26  // Pins can be randomly assigned, this does not affect
+//#define TFT_D3   25  // TFT screen update performance.
+//#define TFT_D4   17
+//#define TFT_D5   16
+//#define TFT_D6   27
+//#define TFT_D7   14
+
+
+// ##################################################################################
+//
+// Section 3. Define the fonts that are to be used here
+//
+// ##################################################################################
+
+// Comment out the #defines below with // to stop that font being loaded
+// The ESP8366 and ESP32 have plenty of memory so commenting out fonts is not
+// normally necessary. If all fonts are loaded the extra FLASH space required is
+// about 17Kbytes. To save FLASH space only enable the fonts you need!
+
+#define LOAD_GLCD   // Font 1. Original Adafruit 8 pixel font needs ~1820 bytes in FLASH
+#define LOAD_FONT2  // Font 2. Small 16 pixel high font, needs ~3534 bytes in FLASH, 96 characters
+#define LOAD_FONT4  // Font 4. Medium 26 pixel high font, needs ~5848 bytes in FLASH, 96 characters
+#define LOAD_FONT6  // Font 6. Large 48 pixel font, needs ~2666 bytes in FLASH, only characters 1234567890:-.apm
+#define LOAD_FONT7  // Font 7. 7 segment 48 pixel font, needs ~2438 bytes in FLASH, only characters 1234567890:-.
+#define LOAD_FONT8  // Font 8. Large 75 pixel font needs ~3256 bytes in FLASH, only characters 1234567890:-.
+//#define LOAD_FONT8N // Font 8. Alternative to Font 8 above, slightly narrower, so 3 digits fit a 160 pixel TFT
+#define LOAD_GFXFF  // FreeFonts. Include access to the 48 Adafruit_GFX free fonts FF1 to FF48 and custom fonts
+
+// Comment out the #define below to stop the SPIFFS filing system and smooth font code being loaded
+// this will save ~20kbytes of FLASH
+#define SMOOTH_FONT
+
+
+// ##################################################################################
+//
+// Section 4. Other options
+//
+// ##################################################################################
+
+// Define the SPI clock frequency, this affects the graphics rendering speed. Too
+// fast and the TFT driver will not keep up and display corruption appears.
+// With an ILI9341 display 40MHz works OK, 80MHz sometimes fails
+// With a ST7735 display more than 27MHz may not work (spurious pixels and lines)
+// With an ILI9163 display 27 MHz works OK.
+
+// #define SPI_FREQUENCY   1000000
+//#define SPI_FREQUENCY   5000000
+// #define SPI_FREQUENCY  10000000
+// #define SPI_FREQUENCY  20000000
+#define SPI_FREQUENCY  27000000 // Marauder // Actually sets it to 26.67MHz = 80/3
+// #define SPI_FREQUENCY  40000000
+// #define SPI_FREQUENCY  80000000
+
+// Optional reduced SPI frequency for reading TFT
+#define SPI_READ_FREQUENCY  20000000
+
+// The XPT2046 requires a lower SPI clock rate of 2.5MHz so we define that here:
+#define SPI_TOUCH_FREQUENCY  2500000
+
+// The ESP32 has 2 free SPI ports i.e. VSPI and HSPI, the VSPI is the default.
+// If the VSPI port is in use and pins are not accessible (e.g. TTGO T-Beam)
+// then uncomment the following line:
+#define USE_HSPI_PORT
+
+// Comment out the following #define if "SPI Transactions" do not need to be
+// supported. When commented out the code size will be smaller and sketches will
+// run slightly faster, so leave it commented out unless you need it!
+
+// Transaction support is needed to work with SD library but not needed with TFT_SdFat
+// Transaction support is required if other SPI devices are connected.
+
+// Transactions are automatically enabled by the library for an ESP32 (to use HAL mutex)
+// so changing it here has no effect
+
+// #define SUPPORT_TRANSACTIONS

User_Setup_cyd_guition.h

@@ -0,0 +1,316 @@
+//                            USER DEFINED SETTINGS
+//   Set driver type, fonts to be loaded, pins used and SPI control method etc
+//
+//   See the User_Setup_Select.h file if you wish to be able to define multiple
+//   setups and then easily select which setup file is used by the compiler.
+//
+//   If this file is edited correctly then all the library example sketches should
+//   run without the need to make any more changes for a particular hardware setup!
+//   Note that some sketches are designed for a particular TFT pixel width/height
+
+
+// ##################################################################################
+//
+// Section 1. Call up the right driver file and any options for it
+//
+// ##################################################################################
+
+// Display type -  only define if RPi display
+//#define RPI_DRIVER
+
+// Only define one driver, the other ones must be commented out
+#define ILI9341_DRIVER // OG Marauder
+//#define ST7735_DRIVER    // Marauder Mini  // Define additional parameters below for this display
+//#define ILI9163_DRIVER     // Define additional parameters below for this display
+//#define S6D02A1_DRIVER
+//#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
+//#define HX8357D_DRIVER
+//#define ILI9481_DRIVER
+//#define ILI9486_DRIVER
+//#define ILI9488_DRIVER     // WARNING: Do not connect ILI9488 display SDO to MISO if other devices share the SPI bus (TFT SDO does NOT tristate when CS is high)
+//#define ST7789_DRIVER      // Full configuration option, define additional parameters below for this display
+//#define ST7789_2_DRIVER    // Minimal configuration option, define additional parameters below for this display
+//#define R61581_DRIVER
+//#define RM68140_DRIVER
+//#define ST7796_DRIVER
+
+// Some displays support SPI reads via the MISO pin, other displays have a single
+// bi-directional SDA pin and the library will try to read this via the MOSI line.
+// To use the SDA line for reading data from the TFT uncomment the following line:
+
+// #define TFT_SDA_READ      // This option is for ESP32 ONLY, tested with ST7789 display only
+
+// For ST7789 and ILI9341 ONLY, define the colour order IF the blue and red are swapped on your display
+// Try ONE option at a time to find the correct colour order for your display
+
+//  #define TFT_RGB_ORDER TFT_RGB  // Colour order Red-Green-Blue
+//  #define TFT_RGB_ORDER TFT_BGR  // Colour order Blue-Green-Red
+
+// For M5Stack ESP32 module with integrated ILI9341 display ONLY, remove // in line below
+
+// #define M5STACK
+
+// For ST7789, ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation
+// #define TFT_WIDTH  80
+// #define TFT_WIDTH  128 // Marauder Mini
+ #define TFT_WIDTH  240 // ST7789 240 x 240 and 240 x 320
+// #define TFT_HEIGHT 160
+// #define TFT_HEIGHT 128 // Marauder Mini
+// #define TFT_HEIGHT 240 // ST7789 240 x 240
+ #define TFT_HEIGHT 320 // ST7789 240 x 320
+
+// For ST7735 ONLY, define the type of display, originally this was based on the
+// colour of the tab on the screen protector film but this is not always true, so try
+// out the different options below if the screen does not display graphics correctly,
+// e.g. colours wrong, mirror images, or tray pixels at the edges.
+// Comment out ALL BUT ONE of these options for a ST7735 display driver, save this
+// this User_Setup file, then rebuild and upload the sketch to the board again:
+
+// #define ST7735_INITB
+// #define ST7735_GREENTAB
+// #define ST7735_GREENTAB2
+// #define ST7735_GREENTAB3
+// #define ST7735_GREENTAB128    // For 128 x 128 display
+// #define ST7735_GREENTAB160x80 // For 160 x 80 display (BGR, inverted, 26 offset)
+// #define ST7735_REDTAB
+// #define ST7735_BLACKTAB
+// #define ST7735_REDTAB160x80   // For 160 x 80 display with 24 pixel offset
+
+// If colours are inverted (white shows as black) then uncomment one of the next
+// 2 lines try both options, one of the options should correct the inversion.
+
+// #define TFT_INVERSION_ON
+// #define TFT_INVERSION_OFF
+
+// If a backlight control signal is available then define the TFT_BL pin in Section 2
+// below. The backlight will be turned ON when tft.begin() is called, but the library
+// needs to know if the LEDs are ON with the pin HIGH or LOW. If the LEDs are to be
+// driven with a PWM signal or turned OFF/ON then this must be handled by the user
+// sketch. e.g. with digitalWrite(TFT_BL, LOW);
+
+// #define TFT_BACKLIGHT_ON LOW  // HIGH or LOW are options
+
+// ##################################################################################
+//
+// Section 2. Define the pins that are used to interface with the display here
+//
+// ##################################################################################
+
+// We must use hardware SPI, a minimum of 3 GPIO pins is needed.
+// Typical setup for ESP8266 NodeMCU ESP-12 is :
+//
+// Display SDO/MISO  to NodeMCU pin D6 (or leave disconnected if not reading TFT)
+// Display LED       to NodeMCU pin VIN (or 5V, see below)
+// Display SCK       to NodeMCU pin D5
+// Display SDI/MOSI  to NodeMCU pin D7
+// Display DC (RS/AO)to NodeMCU pin D3
+// Display RESET     to NodeMCU pin D4 (or RST, see below)
+// Display CS        to NodeMCU pin D8 (or GND, see below)
+// Display GND       to NodeMCU pin GND (0V)
+// Display VCC       to NodeMCU 5V or 3.3V
+//
+// The TFT RESET pin can be connected to the NodeMCU RST pin or 3.3V to free up a control pin
+//
+// The DC (Data Command) pin may be labeled AO or RS (Register Select)
+//
+// With some displays such as the ILI9341 the TFT CS pin can be connected to GND if no more
+// SPI devices (e.g. an SD Card) are connected, in this case comment out the #define TFT_CS
+// line below so it is NOT defined. Other displays such at the ST7735 require the TFT CS pin
+// to be toggled during setup, so in these cases the TFT_CS line must be defined and connected.
+//
+// The NodeMCU D0 pin can be used for RST
+//
+//
+// Note: only some versions of the NodeMCU provide the USB 5V on the VIN pin
+// If 5V is not available at a pin you can use 3.3V but backlight brightness
+// will be lower.
+
+
+// ###### EDIT THE PIN NUMBERS IN THE LINES FOLLOWING TO SUIT YOUR ESP8266 SETUP ######
+
+// For NodeMCU - use pin numbers in the form PIN_Dx where Dx is the NodeMCU pin designation
+//#define TFT_CS   PIN_D8  // Chip select control pin D8
+//#define TFT_DC   PIN_D3  // Data Command control pin
+//#define TFT_RST  PIN_D4  // Reset pin (could connect to NodeMCU RST, see next line)
+//#define TFT_RST  -1    // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
+
+//#define TFT_BL PIN_D1  // LED back-light (only for ST7789 with backlight control pin)
+
+//#define TOUCH_CS PIN_D2     // Chip select pin (T_CS) of touch screen
+
+//#define TFT_WR PIN_D2       // Write strobe for modified Raspberry Pi TFT only
+
+
+// ######  FOR ESP8266 OVERLAP MODE EDIT THE PIN NUMBERS IN THE FOLLOWING LINES  ######
+
+// Overlap mode shares the ESP8266 FLASH SPI bus with the TFT so has a performance impact
+// but saves pins for other functions. It is best not to connect MISO as some displays
+// do not tristate that line wjen chip select is high!
+// On NodeMCU 1.0 SD0=MISO, SD1=MOSI, CLK=SCLK to connect to TFT in overlap mode
+// On NodeMCU V3  S0 =MISO, S1 =MOSI, S2 =SCLK
+// In ESP8266 overlap mode the following must be defined
+
+//#define TFT_SPI_OVERLAP
+
+// In ESP8266 overlap mode the TFT chip select MUST connect to pin D3
+//#define TFT_CS   PIN_D3
+//#define TFT_DC   PIN_D5  // Data Command control pin
+//#define TFT_RST  PIN_D4  // Reset pin (could connect to NodeMCU RST, see next line)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
+
+
+// ###### EDIT THE PIN NUMBERS IN THE LINES FOLLOWING TO SUIT YOUR ESP32 SETUP   ######
+
+// For ESP32 Dev board (only tested with ILI9341 display)
+// The hardware SPI can be mapped to any pins
+
+// Marauder Mini
+/*
+#define TFT_CS   17  // Chip select control pin D8
+#define TFT_DC   16  // Data Command control pin
+#define TFT_RST  5  // Reset pin (could connect to NodeMCU RST, see next line)
+//#define TFT_MISO 19
+//#define TFT_MOSI 23
+//#define TFT_SCLK 18
+//#define TFT_BL   32
+*/
+
+// ESP32 Marauder 
+#define TFT_MISO 12
+#define TFT_MOSI 13
+#define TFT_SCLK 14
+#define TFT_CS   15  // Chip select control pin
+#define TFT_DC   2  // Data Command control pin
+#define TFT_RST   -1  // Reset pin (could connect to RST pin)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if display RESET is connected to ESP32 board RST
+
+#define TFT_BL   27  // LED back-light (only for ST7789 with backlight control pin)
+
+#define TOUCH_CS   33     // Chip select pin (T_CS) of touch screen
+
+/////////////////////////////
+
+// ESP32 Centauri
+/*
+#define TFT_MISO 19
+#define TFT_MOSI 23
+#define TFT_SCLK 18
+#define TFT_CS   27  // Chip select control pin
+#define TFT_DC   26  // Data Command control pin
+#define TFT_RST   5  // Reset pin (could connect to RST pin)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if display RESET is connected to ESP32 board RST
+
+#define TFT_BL   32  // LED back-light (only for ST7789 with backlight control pin)
+
+#define TOUCH_CS 21     // Chip select pin (T_CS) of touch screen
+*/
+/////////////////////////////
+
+//#define TFT_WR 22    // Write strobe for modified Raspberry Pi TFT only
+
+// For the M5Stack module use these #define lines
+//#define TFT_MISO 19
+//#define TFT_MOSI 23
+//#define TFT_SCLK 18
+//#define TFT_CS   14  // Chip select control pin
+//#define TFT_DC   27  // Data Command control pin
+//#define TFT_RST  33  // Reset pin (could connect to Arduino RESET pin)
+//#define TFT_BL   32  // LED back-light (required for M5Stack)
+
+// ######       EDIT THE PINs BELOW TO SUIT YOUR ESP32 PARALLEL TFT SETUP        ######
+
+// The library supports 8 bit parallel TFTs with the ESP32, the pin
+// selection below is compatible with ESP32 boards in UNO format.
+// Wemos D32 boards need to be modified, see diagram in Tools folder.
+// Only ILI9481 and ILI9341 based displays have been tested!
+
+// Parallel bus is only supported on ESP32
+// Uncomment line below to use ESP32 Parallel interface instead of SPI
+
+//#define ESP32_PARALLEL
+
+// The ESP32 and TFT the pins used for testing are:
+//#define TFT_CS   33  // Chip select control pin (library pulls permanently low
+//#define TFT_DC   15  // Data Command control pin - must use a pin in the range 0-31
+//#define TFT_RST  32  // Reset pin, toggles on startup
+
+//#define TFT_WR    4  // Write strobe control pin - must use a pin in the range 0-31
+//#define TFT_RD    2  // Read strobe control pin
+
+//#define TFT_D0   12  // Must use pins in the range 0-31 for the data bus
+//#define TFT_D1   13  // so a single register write sets/clears all bits.
+//#define TFT_D2   26  // Pins can be randomly assigned, this does not affect
+//#define TFT_D3   25  // TFT screen update performance.
+//#define TFT_D4   17
+//#define TFT_D5   16
+//#define TFT_D6   27
+//#define TFT_D7   14
+
+
+// ##################################################################################
+//
+// Section 3. Define the fonts that are to be used here
+//
+// ##################################################################################
+
+// Comment out the #defines below with // to stop that font being loaded
+// The ESP8366 and ESP32 have plenty of memory so commenting out fonts is not
+// normally necessary. If all fonts are loaded the extra FLASH space required is
+// about 17Kbytes. To save FLASH space only enable the fonts you need!
+
+#define LOAD_GLCD   // Font 1. Original Adafruit 8 pixel font needs ~1820 bytes in FLASH
+#define LOAD_FONT2  // Font 2. Small 16 pixel high font, needs ~3534 bytes in FLASH, 96 characters
+#define LOAD_FONT4  // Font 4. Medium 26 pixel high font, needs ~5848 bytes in FLASH, 96 characters
+#define LOAD_FONT6  // Font 6. Large 48 pixel font, needs ~2666 bytes in FLASH, only characters 1234567890:-.apm
+#define LOAD_FONT7  // Font 7. 7 segment 48 pixel font, needs ~2438 bytes in FLASH, only characters 1234567890:-.
+#define LOAD_FONT8  // Font 8. Large 75 pixel font needs ~3256 bytes in FLASH, only characters 1234567890:-.
+//#define LOAD_FONT8N // Font 8. Alternative to Font 8 above, slightly narrower, so 3 digits fit a 160 pixel TFT
+#define LOAD_GFXFF  // FreeFonts. Include access to the 48 Adafruit_GFX free fonts FF1 to FF48 and custom fonts
+
+// Comment out the #define below to stop the SPIFFS filing system and smooth font code being loaded
+// this will save ~20kbytes of FLASH
+#define SMOOTH_FONT
+
+
+// ##################################################################################
+//
+// Section 4. Other options
+//
+// ##################################################################################
+
+// Define the SPI clock frequency, this affects the graphics rendering speed. Too
+// fast and the TFT driver will not keep up and display corruption appears.
+// With an ILI9341 display 40MHz works OK, 80MHz sometimes fails
+// With a ST7735 display more than 27MHz may not work (spurious pixels and lines)
+// With an ILI9163 display 27 MHz works OK.
+
+// #define SPI_FREQUENCY   1000000
+//#define SPI_FREQUENCY   5000000
+// #define SPI_FREQUENCY  10000000
+// #define SPI_FREQUENCY  20000000
+#define SPI_FREQUENCY  27000000 // Marauder // Actually sets it to 26.67MHz = 80/3
+// #define SPI_FREQUENCY  40000000
+// #define SPI_FREQUENCY  80000000
+
+// Optional reduced SPI frequency for reading TFT
+#define SPI_READ_FREQUENCY  20000000
+
+// The XPT2046 requires a lower SPI clock rate of 2.5MHz so we define that here:
+#define SPI_TOUCH_FREQUENCY  2500000
+
+// The ESP32 has 2 free SPI ports i.e. VSPI and HSPI, the VSPI is the default.
+// If the VSPI port is in use and pins are not accessible (e.g. TTGO T-Beam)
+// then uncomment the following line:
+#define USE_HSPI_PORT
+
+// Comment out the following #define if "SPI Transactions" do not need to be
+// supported. When commented out the code size will be smaller and sketches will
+// run slightly faster, so leave it commented out unless you need it!
+
+// Transaction support is needed to work with SD library but not needed with TFT_SdFat
+// Transaction support is required if other SPI devices are connected.
+
+// Transactions are automatically enabled by the library for an ESP32 (to use HAL mutex)
+// so changing it here has no effect
+
+// #define SUPPORT_TRANSACTIONS

User_Setup_cyd_micro.h

@@ -0,0 +1,316 @@
+//                            USER DEFINED SETTINGS
+//   Set driver type, fonts to be loaded, pins used and SPI control method etc
+//
+//   See the User_Setup_Select.h file if you wish to be able to define multiple
+//   setups and then easily select which setup file is used by the compiler.
+//
+//   If this file is edited correctly then all the library example sketches should
+//   run without the need to make any more changes for a particular hardware setup!
+//   Note that some sketches are designed for a particular TFT pixel width/height
+
+
+// ##################################################################################
+//
+// Section 1. Call up the right driver file and any options for it
+//
+// ##################################################################################
+
+// Display type -  only define if RPi display
+//#define RPI_DRIVER
+
+// Only define one driver, the other ones must be commented out
+#define ILI9341_DRIVER // OG Marauder
+//#define ST7735_DRIVER    // Marauder Mini  // Define additional parameters below for this display
+//#define ILI9163_DRIVER     // Define additional parameters below for this display
+//#define S6D02A1_DRIVER
+//#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
+//#define HX8357D_DRIVER
+//#define ILI9481_DRIVER
+//#define ILI9486_DRIVER
+//#define ILI9488_DRIVER     // WARNING: Do not connect ILI9488 display SDO to MISO if other devices share the SPI bus (TFT SDO does NOT tristate when CS is high)
+//#define ST7789_DRIVER      // Full configuration option, define additional parameters below for this display
+//#define ST7789_2_DRIVER    // Minimal configuration option, define additional parameters below for this display
+//#define R61581_DRIVER
+//#define RM68140_DRIVER
+//#define ST7796_DRIVER
+
+// Some displays support SPI reads via the MISO pin, other displays have a single
+// bi-directional SDA pin and the library will try to read this via the MOSI line.
+// To use the SDA line for reading data from the TFT uncomment the following line:
+
+// #define TFT_SDA_READ      // This option is for ESP32 ONLY, tested with ST7789 display only
+
+// For ST7789 and ILI9341 ONLY, define the colour order IF the blue and red are swapped on your display
+// Try ONE option at a time to find the correct colour order for your display
+
+//  #define TFT_RGB_ORDER TFT_RGB  // Colour order Red-Green-Blue
+//  #define TFT_RGB_ORDER TFT_BGR  // Colour order Blue-Green-Red
+
+// For M5Stack ESP32 module with integrated ILI9341 display ONLY, remove // in line below
+
+// #define M5STACK
+
+// For ST7789, ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation
+// #define TFT_WIDTH  80
+// #define TFT_WIDTH  128 // Marauder Mini
+ #define TFT_WIDTH  240 // ST7789 240 x 240 and 240 x 320
+// #define TFT_HEIGHT 160
+// #define TFT_HEIGHT 128 // Marauder Mini
+// #define TFT_HEIGHT 240 // ST7789 240 x 240
+ #define TFT_HEIGHT 320 // ST7789 240 x 320
+
+// For ST7735 ONLY, define the type of display, originally this was based on the
+// colour of the tab on the screen protector film but this is not always true, so try
+// out the different options below if the screen does not display graphics correctly,
+// e.g. colours wrong, mirror images, or tray pixels at the edges.
+// Comment out ALL BUT ONE of these options for a ST7735 display driver, save this
+// this User_Setup file, then rebuild and upload the sketch to the board again:
+
+// #define ST7735_INITB
+// #define ST7735_GREENTAB
+// #define ST7735_GREENTAB2
+// #define ST7735_GREENTAB3
+// #define ST7735_GREENTAB128    // For 128 x 128 display
+// #define ST7735_GREENTAB160x80 // For 160 x 80 display (BGR, inverted, 26 offset)
+// #define ST7735_REDTAB
+// #define ST7735_BLACKTAB
+// #define ST7735_REDTAB160x80   // For 160 x 80 display with 24 pixel offset
+
+// If colours are inverted (white shows as black) then uncomment one of the next
+// 2 lines try both options, one of the options should correct the inversion.
+
+// #define TFT_INVERSION_ON
+// #define TFT_INVERSION_OFF
+
+// If a backlight control signal is available then define the TFT_BL pin in Section 2
+// below. The backlight will be turned ON when tft.begin() is called, but the library
+// needs to know if the LEDs are ON with the pin HIGH or LOW. If the LEDs are to be
+// driven with a PWM signal or turned OFF/ON then this must be handled by the user
+// sketch. e.g. with digitalWrite(TFT_BL, LOW);
+
+// #define TFT_BACKLIGHT_ON LOW  // HIGH or LOW are options
+
+// ##################################################################################
+//
+// Section 2. Define the pins that are used to interface with the display here
+//
+// ##################################################################################
+
+// We must use hardware SPI, a minimum of 3 GPIO pins is needed.
+// Typical setup for ESP8266 NodeMCU ESP-12 is :
+//
+// Display SDO/MISO  to NodeMCU pin D6 (or leave disconnected if not reading TFT)
+// Display LED       to NodeMCU pin VIN (or 5V, see below)
+// Display SCK       to NodeMCU pin D5
+// Display SDI/MOSI  to NodeMCU pin D7
+// Display DC (RS/AO)to NodeMCU pin D3
+// Display RESET     to NodeMCU pin D4 (or RST, see below)
+// Display CS        to NodeMCU pin D8 (or GND, see below)
+// Display GND       to NodeMCU pin GND (0V)
+// Display VCC       to NodeMCU 5V or 3.3V
+//
+// The TFT RESET pin can be connected to the NodeMCU RST pin or 3.3V to free up a control pin
+//
+// The DC (Data Command) pin may be labeled AO or RS (Register Select)
+//
+// With some displays such as the ILI9341 the TFT CS pin can be connected to GND if no more
+// SPI devices (e.g. an SD Card) are connected, in this case comment out the #define TFT_CS
+// line below so it is NOT defined. Other displays such at the ST7735 require the TFT CS pin
+// to be toggled during setup, so in these cases the TFT_CS line must be defined and connected.
+//
+// The NodeMCU D0 pin can be used for RST
+//
+//
+// Note: only some versions of the NodeMCU provide the USB 5V on the VIN pin
+// If 5V is not available at a pin you can use 3.3V but backlight brightness
+// will be lower.
+
+
+// ###### EDIT THE PIN NUMBERS IN THE LINES FOLLOWING TO SUIT YOUR ESP8266 SETUP ######
+
+// For NodeMCU - use pin numbers in the form PIN_Dx where Dx is the NodeMCU pin designation
+//#define TFT_CS   PIN_D8  // Chip select control pin D8
+//#define TFT_DC   PIN_D3  // Data Command control pin
+//#define TFT_RST  PIN_D4  // Reset pin (could connect to NodeMCU RST, see next line)
+//#define TFT_RST  -1    // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
+
+//#define TFT_BL PIN_D1  // LED back-light (only for ST7789 with backlight control pin)
+
+//#define TOUCH_CS PIN_D2     // Chip select pin (T_CS) of touch screen
+
+//#define TFT_WR PIN_D2       // Write strobe for modified Raspberry Pi TFT only
+
+
+// ######  FOR ESP8266 OVERLAP MODE EDIT THE PIN NUMBERS IN THE FOLLOWING LINES  ######
+
+// Overlap mode shares the ESP8266 FLASH SPI bus with the TFT so has a performance impact
+// but saves pins for other functions. It is best not to connect MISO as some displays
+// do not tristate that line wjen chip select is high!
+// On NodeMCU 1.0 SD0=MISO, SD1=MOSI, CLK=SCLK to connect to TFT in overlap mode
+// On NodeMCU V3  S0 =MISO, S1 =MOSI, S2 =SCLK
+// In ESP8266 overlap mode the following must be defined
+
+//#define TFT_SPI_OVERLAP
+
+// In ESP8266 overlap mode the TFT chip select MUST connect to pin D3
+//#define TFT_CS   PIN_D3
+//#define TFT_DC   PIN_D5  // Data Command control pin
+//#define TFT_RST  PIN_D4  // Reset pin (could connect to NodeMCU RST, see next line)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
+
+
+// ###### EDIT THE PIN NUMBERS IN THE LINES FOLLOWING TO SUIT YOUR ESP32 SETUP   ######
+
+// For ESP32 Dev board (only tested with ILI9341 display)
+// The hardware SPI can be mapped to any pins
+
+// Marauder Mini
+/*
+#define TFT_CS   17  // Chip select control pin D8
+#define TFT_DC   16  // Data Command control pin
+#define TFT_RST  5  // Reset pin (could connect to NodeMCU RST, see next line)
+//#define TFT_MISO 19
+//#define TFT_MOSI 23
+//#define TFT_SCLK 18
+//#define TFT_BL   32
+*/
+
+// ESP32 Marauder 
+#define TFT_MISO 12
+#define TFT_MOSI 13
+#define TFT_SCLK 14
+#define TFT_CS   15  // Chip select control pin
+#define TFT_DC   2  // Data Command control pin
+#define TFT_RST   -1  // Reset pin (could connect to RST pin)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if display RESET is connected to ESP32 board RST
+
+#define TFT_BL   21  // LED back-light (only for ST7789 with backlight control pin)
+
+#define TOUCH_CS   33     // Chip select pin (T_CS) of touch screen
+
+/////////////////////////////
+
+// ESP32 Centauri
+/*
+#define TFT_MISO 19
+#define TFT_MOSI 23
+#define TFT_SCLK 18
+#define TFT_CS   27  // Chip select control pin
+#define TFT_DC   26  // Data Command control pin
+#define TFT_RST   5  // Reset pin (could connect to RST pin)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if display RESET is connected to ESP32 board RST
+
+#define TFT_BL   32  // LED back-light (only for ST7789 with backlight control pin)
+
+#define TOUCH_CS 21     // Chip select pin (T_CS) of touch screen
+*/
+/////////////////////////////
+
+//#define TFT_WR 22    // Write strobe for modified Raspberry Pi TFT only
+
+// For the M5Stack module use these #define lines
+//#define TFT_MISO 19
+//#define TFT_MOSI 23
+//#define TFT_SCLK 18
+//#define TFT_CS   14  // Chip select control pin
+//#define TFT_DC   27  // Data Command control pin
+//#define TFT_RST  33  // Reset pin (could connect to Arduino RESET pin)
+//#define TFT_BL   32  // LED back-light (required for M5Stack)
+
+// ######       EDIT THE PINs BELOW TO SUIT YOUR ESP32 PARALLEL TFT SETUP        ######
+
+// The library supports 8 bit parallel TFTs with the ESP32, the pin
+// selection below is compatible with ESP32 boards in UNO format.
+// Wemos D32 boards need to be modified, see diagram in Tools folder.
+// Only ILI9481 and ILI9341 based displays have been tested!
+
+// Parallel bus is only supported on ESP32
+// Uncomment line below to use ESP32 Parallel interface instead of SPI
+
+//#define ESP32_PARALLEL
+
+// The ESP32 and TFT the pins used for testing are:
+//#define TFT_CS   33  // Chip select control pin (library pulls permanently low
+//#define TFT_DC   15  // Data Command control pin - must use a pin in the range 0-31
+//#define TFT_RST  32  // Reset pin, toggles on startup
+
+//#define TFT_WR    4  // Write strobe control pin - must use a pin in the range 0-31
+//#define TFT_RD    2  // Read strobe control pin
+
+//#define TFT_D0   12  // Must use pins in the range 0-31 for the data bus
+//#define TFT_D1   13  // so a single register write sets/clears all bits.
+//#define TFT_D2   26  // Pins can be randomly assigned, this does not affect
+//#define TFT_D3   25  // TFT screen update performance.
+//#define TFT_D4   17
+//#define TFT_D5   16
+//#define TFT_D6   27
+//#define TFT_D7   14
+
+
+// ##################################################################################
+//
+// Section 3. Define the fonts that are to be used here
+//
+// ##################################################################################
+
+// Comment out the #defines below with // to stop that font being loaded
+// The ESP8366 and ESP32 have plenty of memory so commenting out fonts is not
+// normally necessary. If all fonts are loaded the extra FLASH space required is
+// about 17Kbytes. To save FLASH space only enable the fonts you need!
+
+#define LOAD_GLCD   // Font 1. Original Adafruit 8 pixel font needs ~1820 bytes in FLASH
+#define LOAD_FONT2  // Font 2. Small 16 pixel high font, needs ~3534 bytes in FLASH, 96 characters
+#define LOAD_FONT4  // Font 4. Medium 26 pixel high font, needs ~5848 bytes in FLASH, 96 characters
+#define LOAD_FONT6  // Font 6. Large 48 pixel font, needs ~2666 bytes in FLASH, only characters 1234567890:-.apm
+#define LOAD_FONT7  // Font 7. 7 segment 48 pixel font, needs ~2438 bytes in FLASH, only characters 1234567890:-.
+#define LOAD_FONT8  // Font 8. Large 75 pixel font needs ~3256 bytes in FLASH, only characters 1234567890:-.
+//#define LOAD_FONT8N // Font 8. Alternative to Font 8 above, slightly narrower, so 3 digits fit a 160 pixel TFT
+#define LOAD_GFXFF  // FreeFonts. Include access to the 48 Adafruit_GFX free fonts FF1 to FF48 and custom fonts
+
+// Comment out the #define below to stop the SPIFFS filing system and smooth font code being loaded
+// this will save ~20kbytes of FLASH
+#define SMOOTH_FONT
+
+
+// ##################################################################################
+//
+// Section 4. Other options
+//
+// ##################################################################################
+
+// Define the SPI clock frequency, this affects the graphics rendering speed. Too
+// fast and the TFT driver will not keep up and display corruption appears.
+// With an ILI9341 display 40MHz works OK, 80MHz sometimes fails
+// With a ST7735 display more than 27MHz may not work (spurious pixels and lines)
+// With an ILI9163 display 27 MHz works OK.
+
+// #define SPI_FREQUENCY   1000000
+//#define SPI_FREQUENCY   5000000
+// #define SPI_FREQUENCY  10000000
+// #define SPI_FREQUENCY  20000000
+#define SPI_FREQUENCY  27000000 // Marauder // Actually sets it to 26.67MHz = 80/3
+// #define SPI_FREQUENCY  40000000
+// #define SPI_FREQUENCY  80000000
+
+// Optional reduced SPI frequency for reading TFT
+#define SPI_READ_FREQUENCY  20000000
+
+// The XPT2046 requires a lower SPI clock rate of 2.5MHz so we define that here:
+#define SPI_TOUCH_FREQUENCY  2500000
+
+// The ESP32 has 2 free SPI ports i.e. VSPI and HSPI, the VSPI is the default.
+// If the VSPI port is in use and pins are not accessible (e.g. TTGO T-Beam)
+// then uncomment the following line:
+#define USE_HSPI_PORT
+
+// Comment out the following #define if "SPI Transactions" do not need to be
+// supported. When commented out the code size will be smaller and sketches will
+// run slightly faster, so leave it commented out unless you need it!
+
+// Transaction support is needed to work with SD library but not needed with TFT_SdFat
+// Transaction support is required if other SPI devices are connected.
+
+// Transactions are automatically enabled by the library for an ESP32 (to use HAL mutex)
+// so changing it here has no effect
+
+// #define SUPPORT_TRANSACTIONS

esp32_marauder/Assets.h

@@ -215,7 +215,13 @@ PROGMEM static const unsigned char menu_icons[][66] = {
     0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 
     0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 
     0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 
-    0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF}
+    0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF},
+    {0xFF, 0xFF, 0x3F, 0xFF, 0xF7, 0x3F, 0x7F, 0x96, 0x3F, 0xFF, 0xED, 0x3F, // PINESCAN_SNIFF: 37
+    0x3F, 0x25, 0x3F, 0xDF, 0xD2, 0x3E, 0xFF, 0xED, 0x3F, 0x7F, 0x8E, 0x3F, 
+    0x3B, 0x77, 0x37, 0xBD, 0x6A, 0x2F, 0xD6, 0xBD, 0x1A, 0xDA, 0xDA, 0x16, 
+    0x5A, 0x6F, 0x16, 0x9A, 0xF7, 0x16, 0xD6, 0x5A, 0x1A, 0xDD, 0xBD, 0x2E, 
+    0xBB, 0x5A, 0x37, 0x3F, 0x6F, 0x3F, 0x7F, 0xB7, 0x3F, 0xFF, 0xCC, 0x3F, 
+    0xFF, 0xF3, 0x3F, 0xFF, 0xFF, 0x3F}
 };
 
 /*#ifndef MARAUDER_MINI

esp32_marauder/CommandLine.cpp

@@ -229,6 +229,8 @@ void CommandLine::runCommand(String input) {
     Serial.println(HELP_SNIFF_BEACON_CMD);
     Serial.println(HELP_SNIFF_PROBE_CMD);
     Serial.println(HELP_SNIFF_PWN_CMD);
+    Serial.println(HELP_SNIFF_PINESCAN_CMD);
+    Serial.println(HELP_SNIFF_MULTISSID_CMD);
     Serial.println(HELP_SNIFF_ESP_CMD);
     Serial.println(HELP_SNIFF_DEAUTH_CMD);
     Serial.println(HELP_SNIFF_PMKID_CMD);
@@ -683,6 +685,24 @@ void CommandLine::runCommand(String input) {
       #endif
       wifi_scan_obj.StartScan(WIFI_SCAN_PWN, TFT_MAGENTA);
     }
+    // PineScan sniff
+    else if (cmd_args.get(0) == SNIFF_PINESCAN_CMD) {
+      Serial.println("Starting Pinescan sniff. Stop with " + (String)STOPSCAN_CMD);
+      #ifdef HAS_SCREEN
+        display_obj.clearScreen();
+        menu_function_obj.drawStatusBar();
+      #endif
+      wifi_scan_obj.StartScan(WIFI_SCAN_PINESCAN, TFT_MAGENTA);
+    }
+    // MultiSSID sniff
+    else if (cmd_args.get(0) == SNIFF_MULTISSID_CMD) {
+      Serial.println("Starting MultiSSID sniff. Stop with " + (String)STOPSCAN_CMD);
+      #ifdef HAS_SCREEN
+        display_obj.clearScreen();
+        menu_function_obj.drawStatusBar();
+      #endif
+      wifi_scan_obj.StartScan(WIFI_SCAN_MULTISSID, TFT_MAGENTA);
+    }
     // Espressif sniff
     else if (cmd_args.get(0) == SNIFF_ESP_CMD) {
       Serial.println("Starting Espressif device sniff. Stop with " + (String)STOPSCAN_CMD);

esp32_marauder/CommandLine.h

@@ -63,6 +63,8 @@ const char PROGMEM SNIFF_RAW_CMD[] = "sniffraw";
 const char PROGMEM SNIFF_BEACON_CMD[] = "sniffbeacon";
 const char PROGMEM SNIFF_PROBE_CMD[] = "sniffprobe";
 const char PROGMEM SNIFF_PWN_CMD[] = "sniffpwn";
+const char PROGMEM SNIFF_PINESCAN_CMD[] = "sniffpinescan";
+const char PROGMEM SNIFF_MULTISSID_CMD[] = "sniffmultissid";
 const char PROGMEM SNIFF_ESP_CMD[] = "sniffesp";
 const char PROGMEM SNIFF_DEAUTH_CMD[] = "sniffdeauth";
 const char PROGMEM SNIFF_PMKID_CMD[] = "sniffpmkid";
@@ -121,6 +123,8 @@ const char PROGMEM HELP_SNIFF_RAW_CMD[] = "sniffraw";
 const char PROGMEM HELP_SNIFF_BEACON_CMD[] = "sniffbeacon";
 const char PROGMEM HELP_SNIFF_PROBE_CMD[] = "sniffprobe";
 const char PROGMEM HELP_SNIFF_PWN_CMD[] = "sniffpwn";
+const char PROGMEM HELP_SNIFF_PINESCAN_CMD[] = "sniffpinescan";
+const char PROGMEM HELP_SNIFF_MULTISSID_CMD[] = "sniffmultissid";
 const char PROGMEM HELP_SNIFF_ESP_CMD[] = "sniffesp";
 const char PROGMEM HELP_SNIFF_DEAUTH_CMD[] = "sniffdeauth";
 const char PROGMEM HELP_SNIFF_PMKID_CMD[] = "sniffpmkid [-c <channel>][-d][-l]";

esp32_marauder/Display.cpp

@@ -4,9 +4,82 @@
 #ifdef HAS_SCREEN
 
 Display::Display()
+#ifdef HAS_CYD_TOUCH
+  : touchscreenSPI(VSPI),
+    touchscreen(XPT2046_CS, XPT2046_IRQ)
+#endif
 {
 }
 
+int8_t Display::menuButton(uint16_t *x, uint16_t *y, bool pressed) {
+  #ifdef HAS_ILI9341
+    for (uint8_t b = BUTTON_ARRAY_LEN; b < BUTTON_ARRAY_LEN + 3; b++) {
+      if (pressed && this->key[b].contains(*x, *y)) {
+        this->key[b].press(true);  // tell the button it is pressed
+      } else {
+        this->key[b].press(false);  // tell the button it is NOT pressed
+      }
+    }
+
+    for (uint8_t b = BUTTON_ARRAY_LEN; b < BUTTON_ARRAY_LEN + 3; b++) {
+      if ((this->key[b].justReleased()) && (!pressed)) {
+        return b - BUTTON_ARRAY_LEN;
+      }
+    }
+
+  #endif
+
+  return -1;
+}
+
+uint8_t Display::updateTouch(uint16_t *x, uint16_t *y, uint16_t threshold) {
+  #ifdef HAS_ILI9341
+    if (!this->headless_mode)
+      #ifndef HAS_CYD_TOUCH
+        return this->tft.getTouch(x, y, threshold);
+      #else
+        if (this->touchscreen.tirqTouched() && this->touchscreen.touched()) {
+          TS_Point p = this->touchscreen.getPoint();
+
+          //*x = map(p.x, 200, 3700, 1, TFT_WIDTH);
+          //*y = map(p.y, 240, 3800, 1, TFT_HEIGHT);
+
+          uint8_t rot = this->tft.getRotation();
+
+          //#ifdef HAS_CYD_PORTRAIT
+          //  rot = 0;
+          //#endif
+
+          switch (rot) {
+            case 0: // Standard Protrait
+              *x = map(p.x, 200, 3700, 1, TFT_WIDTH);
+              *y = map(p.y, 240, 3800, 1, TFT_HEIGHT);
+              break;
+            case 1:
+              *x = map(p.y, 143, 3715, 0, TFT_HEIGHT);     // Horizontal (Y axis in touch, X on screen)
+              *y = map(p.x, 3786, 216, 0, TFT_WIDTH);    // Vertical (X axis in touch, Y on screen)
+              break;
+            case 2:
+              *x = map(p.x, 3700, 200, 1, TFT_WIDTH);
+              *y = map(p.y, 3800, 240, 1, TFT_HEIGHT);
+              break;
+            case 3:
+              *x = map(p.y, 3800, 240, 1, TFT_WIDTH);
+              *y = map(p.x, 200, 3700, 1, TFT_HEIGHT);
+              break;
+          }
+          return 1;
+        }
+        else
+          return 0;
+      #endif
+    else
+      return !this->headless_mode;
+  #endif
+
+  return 0;
+}
+
 // Function to prepare the display and the menus
 void Display::RunSetup()
 {
@@ -18,32 +91,47 @@ void Display::RunSetup()
   #ifdef SCREEN_BUFFER
     screen_buffer = new LinkedList<String>();
   #endif
+
+  #ifdef HAS_CYD_TOUCH
+    this->touchscreenSPI.begin(XPT2046_CLK, XPT2046_MISO, XPT2046_MOSI, XPT2046_CS);
+    this->touchscreen.begin(touchscreenSPI);
+    this->touchscreen.setRotation(0);
+  #endif
   
   tft.init();
-  #ifndef MARAUDER_M5STICKC
+
+  tft.setRotation(SCREEN_ORIENTATION);
+
+  /*#ifndef MARAUDER_M5STICKC
     tft.setRotation(0); // Portrait
   #endif
 
+  #ifdef HAS_CYD_PORTRAIT
+    tft.setRotation(3); // Bro these CYDs are so stupid
+  #endif
+
   #ifdef MARAUDER_M5STICKC
     tft.setRotation(1);
   #endif
 
   #ifdef MARAUDER_REV_FEATHER
     tft.setRotation(1);
-  #endif
+  #endif*/
 
   tft.setCursor(0, 0);
 
   #ifdef HAS_ILI9341
 
-    #ifdef TFT_SHIELD
-      uint16_t calData[5] = { 275, 3494, 361, 3528, 4 }; // tft.setRotation(0); // Portrait with TFT Shield
-      //Serial.println(F("Using TFT Shield"));
-    #else if defined(TFT_DIY)
-      uint16_t calData[5] = { 339, 3470, 237, 3438, 2 }; // tft.setRotation(0); // Portrait with DIY TFT
-      //Serial.println(F("Using TFT DIY"));
+    #ifndef HAS_CYD_TOUCH
+      #ifdef TFT_SHIELD
+        uint16_t calData[5] = { 275, 3494, 361, 3528, 4 }; // tft.setRotation(0); // Portrait with TFT Shield
+        //Serial.println(F("Using TFT Shield"));
+      #elif defined(TFT_DIY)
+        uint16_t calData[5] = { 339, 3470, 237, 3438, 2 }; // tft.setRotation(0); // Portrait with DIY TFT
+        //Serial.println(F("Using TFT DIY"));
+      #endif
+      tft.setTouch(calData);
     #endif
-    tft.setTouch(calData);
 
   #endif
 
@@ -476,7 +564,11 @@ void Display::setupScrollArea(uint16_t tfa, uint16_t bfa) {
   //Serial.println("   bfa: " + (String)bfa);
   //Serial.println("yStart: " + (String)this->yStart);
   #ifdef HAS_ILI9341
-    tft.writecommand(ILI9341_VSCRDEF); // Vertical scroll definition
+    #ifdef HAS_ST7789
+      tft.writecommand(ST7789_VSCRDEF); // Vertical scroll definition
+    #else
+      tft.writecommand(ILI9341_VSCRDEF);
+    #endif
     tft.writedata(tfa >> 8);           // Top Fixed Area line count
     tft.writedata(tfa);
     tft.writedata((YMAX-tfa-bfa)>>8);  // Vertical Scrolling Area line count
@@ -489,7 +581,11 @@ void Display::setupScrollArea(uint16_t tfa, uint16_t bfa) {
 
 void Display::scrollAddress(uint16_t vsp) {
   #ifdef HAS_ILI9341
-    tft.writecommand(ILI9341_VSCRSADD); // Vertical scrolling pointer
+    #ifdef HAS_ST7789
+      tft.writecommand(ST7789_VSCRDEF); // Vertical scroll definition
+    #else
+      tft.writecommand(ILI9341_VSCRDEF);
+    #endif
     tft.writedata(vsp>>8);
     tft.writedata(vsp);
   #endif

esp32_marauder/Display.h

@@ -19,6 +19,10 @@
 
 #include <TFT_eSPI.h>
 
+#ifdef HAS_CYD_TOUCH
+  #include <XPT2046_Touchscreen.h>
+#endif
+
 // WiFi stuff
 #define OTA_UPDATE 100
 #define SHOW_INFO 101
@@ -45,6 +49,10 @@
 #define MAGENTA_KEY ";mgn;"
 #define WHITE_KEY ";wht;"
 
+#define UP_BUTTON     0
+#define SELECT_BUTTON 1
+#define DOWN_BUTTON   2
+
 class Display
 {
   private:
@@ -69,9 +77,14 @@ class Display
   public:
     Display();
     TFT_eSPI tft = TFT_eSPI();
-    TFT_eSPI_Button key[BUTTON_ARRAY_LEN];
+    TFT_eSPI_Button key[BUTTON_ARRAY_LEN + 3];
     const String PROGMEM version_number = MARAUDER_VERSION;
 
+    #ifdef HAS_CYD_TOUCH
+      SPIClass touchscreenSPI;
+      XPT2046_Touchscreen touchscreen;
+    #endif
+
     bool printing = false;
     bool loading = false;
     bool tteBar = false;
@@ -105,6 +118,8 @@ class Display
     // We can speed up scrolling of short text lines by just blanking the character we drew
     int blank[19]; // We keep all the strings pixel lengths to optimise the speed of the top line blanking
 
+    int8_t menuButton(uint16_t *x, uint16_t *y, bool pressed);
+    uint8_t updateTouch(uint16_t *x, uint16_t *y, uint16_t threshold = 600);
     void tftDrawRedOnOffButton();
     void tftDrawGreenOnOffButton();
     void tftDrawGraphObjects(byte x_scale);

esp32_marauder/EvilPortal.cpp

@@ -1,5 +1,9 @@
 #include "EvilPortal.h"
 
+#ifdef HAS_PSRAM
+  char* index_html = nullptr;
+#endif
+
 AsyncWebServer server(80);
 
 EvilPortal::EvilPortal() {
@@ -23,6 +27,13 @@ void EvilPortal::setup() {
   #endif
 }
 
+void EvilPortal::cleanup() {
+  #ifdef HAS_PSRAM
+    free(index_html);
+    index_html = nullptr;
+  #endif
+}
+
 bool EvilPortal::begin(LinkedList<ssid>* ssids, LinkedList<AccessPoint>* access_points) {
   if (!this->setAP(ssids, access_points))
     return false;
@@ -43,12 +54,26 @@ String EvilPortal::get_password() {
 }
 
 void EvilPortal::setupServer() {
-  server.on("/", HTTP_GET, [this](AsyncWebServerRequest *request) {
-    request->send_P(200, "text/html", index_html);
-    Serial.println("client connected");
-    #ifdef HAS_SCREEN
-      this->sendToDisplay("Client connected to server");
-    #endif
+  #ifndef HAS_PSRAM
+    server.on("/", HTTP_GET, [this](AsyncWebServerRequest *request) {
+      request->send_P(200, "text/html", index_html);
+      Serial.println("client connected");
+      #ifdef HAS_SCREEN
+        this->sendToDisplay("Client connected to server");
+      #endif
+    });
+  #else
+    server.on("/", HTTP_GET, [this](AsyncWebServerRequest *request) {
+      request->send(200, "text/html", index_html);
+      Serial.println("client connected");
+      #ifdef HAS_SCREEN
+        this->sendToDisplay("Client connected to server");
+      #endif
+    });
+  #endif
+
+  server.on("/get-ap-name", HTTP_GET, [this](AsyncWebServerRequest *request) {
+    request->send(200, "text/plain", WiFi.softAPSSID());
   });
 
   server.on("/get", HTTP_GET, [this](AsyncWebServerRequest *request) {
@@ -78,7 +103,13 @@ void EvilPortal::setupServer() {
 void EvilPortal::setHtmlFromSerial() {
   Serial.println("Setting HTML from serial...");
   const char *htmlStr = Serial.readString().c_str();
-  strncpy(index_html, htmlStr, strlen(htmlStr));
+  #ifdef HAS_PSRAM
+    index_html = (char*) ps_malloc(MAX_HTML_SIZE);
+  #endif
+  strlcpy(index_html, htmlStr, strlen(htmlStr));
+  #ifdef HAS_PSRAM
+    index_html[MAX_HTML_SIZE - 1] = '\0';
+  #endif
   this->has_html = true;
   this->using_serial_html = true;
   Serial.println("html set");
@@ -119,7 +150,13 @@ bool EvilPortal::setHtml() {
       if (isPrintable(c))
         html.concat(c);
     }
-    strncpy(index_html, html.c_str(), strlen(html.c_str()));
+    #ifdef HAS_PSRAM
+      index_html = (char*) ps_malloc(MAX_HTML_SIZE);
+    #endif
+    strlcpy(index_html, html.c_str(), strlen(html.c_str()));
+    #ifdef HAS_PSRAM
+      index_html[MAX_HTML_SIZE - 1] = '\0';
+    #endif
     this->has_html = true;
     Serial.println("html set");
     html_file.close();

esp32_marauder/EvilPortal.h

@@ -37,7 +37,12 @@ extern Buffer buffer_obj;
 #define WIFI_SCAN_EVIL_PORTAL 30
 
 char apName[MAX_AP_NAME_SIZE] = "PORTAL";
-char index_html[MAX_HTML_SIZE] = "TEST";
+
+#ifndef HAS_PSRAM
+  char index_html[MAX_HTML_SIZE] = "TEST";
+#else
+  extern char* index_html;
+#endif
 
 struct ssid {
   String essid;
@@ -51,7 +56,8 @@ struct AccessPoint {
   uint8_t channel;
   uint8_t bssid[6];
   bool selected;
-  LinkedList<char>* beacon;
+ // LinkedList<char>* beacon;
+  char beacon[2];
   int8_t rssi;
   LinkedList<uint16_t>* stations;
   uint16_t packets;
@@ -106,6 +112,7 @@ class EvilPortal {
 
     LinkedList<String>* html_files;
 
+    void cleanup();
     String get_user_name();
     String get_password();
     void setup();

esp32_marauder/MenuFunctions.cpp

@@ -18,13 +18,6 @@ MenuFunctions::MenuFunctions()
 /* Interrupt driven periodic handler */
 
 #ifdef HAS_ILI9341
-  uint8_t MenuFunctions::updateTouch(uint16_t *x, uint16_t *y, uint16_t threshold) {
-    if (!display_obj.headless_mode)
-      return display_obj.tft.getTouch(x, y, threshold);
-    else
-      return !display_obj.headless_mode;
-  }
-
   void MenuFunctions::lv_tick_handler()
   {
     lv_tick_inc(LVGL_TICK_PERIOD);
@@ -56,7 +49,7 @@ MenuFunctions::MenuFunctions()
     
     uint16_t touchX, touchY;
   
-    bool touched = display_obj.tft.getTouch(&touchX, &touchY, 600);
+    bool touched = display_obj.updateTouch(&touchX, &touchY, 600);
   
     if(!touched)
     {
@@ -660,6 +653,42 @@ void MenuFunctions::buttonSelected(int b, int x) {
   #endif
 }
 
+void MenuFunctions::displayMenuButtons() {
+  #ifdef HAS_ILI9341
+    // Draw lines to show each menu button
+    for (int i = 0; i < 3; i++) {
+
+      // Draw horizontal line on left
+      display_obj.tft.drawLine(0, 
+                              TFT_HEIGHT / 3 * (i),
+                              (TFT_WIDTH / 12) / 2,
+                              TFT_HEIGHT / 3 * (i),
+                              TFT_FARTGRAY);
+
+      // Draw horizontal line on right
+      display_obj.tft.drawLine(TFT_WIDTH - 1 - ((TFT_WIDTH / 12) / 2), 
+                              TFT_HEIGHT / 3 * (i),
+                              TFT_WIDTH,
+                              TFT_HEIGHT / 3 * (i),
+                              TFT_FARTGRAY);
+
+      // Draw vertical line on left
+      display_obj.tft.drawLine(0, 
+                              (TFT_HEIGHT / 3 * (i)) - ((TFT_WIDTH / 12) / 2),
+                              0,
+                              (TFT_HEIGHT / 3 * (i)) + ((TFT_WIDTH / 12) / 2),
+                              TFT_FARTGRAY);
+
+      // Draw vertical line on right
+      display_obj.tft.drawLine(TFT_WIDTH - 1, 
+                              (TFT_HEIGHT / 3 * (i)) - ((TFT_WIDTH / 12) / 2),
+                              TFT_WIDTH - 1,
+                              (TFT_HEIGHT / 3 * (i)) + ((TFT_WIDTH / 12) / 2),
+                              TFT_FARTGRAY);
+    }
+  #endif
+}
+
 // Function to check menu input
 void MenuFunctions::main(uint32_t currentTime)
 {
@@ -679,11 +708,6 @@ void MenuFunctions::main(uint32_t currentTime)
       this->orientDisplay();
       wifi_scan_obj.orient_display = false;
     }
-    /*#ifdef HAS_ILI9341
-      if ((wifi_scan_obj.currentScanMode != LV_JOIN_WIFI) &&
-          (wifi_scan_obj.currentScanMode != LV_ADD_SSID))
-        display_obj.updateBanner(current_menu->name);
-    #endif*/
   }
 
   if (currentTime != 0) {
@@ -723,13 +747,11 @@ void MenuFunctions::main(uint32_t currentTime)
     display_obj.displayBuffer();
 
 
-  // Pressed will be set true is there is a valid touch on the screen
   int pre_getTouch = millis();
 
-  // getTouch causes a 10ms delay which makes beacon spam less effective
   #ifdef HAS_ILI9341
     if (!this->disable_touch)
-      pressed = this->updateTouch(&t_x, &t_y);
+      pressed = display_obj.updateTouch(&t_x, &t_y);
   #endif
 
 
@@ -754,6 +776,8 @@ void MenuFunctions::main(uint32_t currentTime)
           (wifi_scan_obj.currentScanMode == WIFI_SCAN_TARGET_AP_FULL) ||
           (wifi_scan_obj.currentScanMode == WIFI_SCAN_AP_STA) ||
           (wifi_scan_obj.currentScanMode == WIFI_SCAN_PWN) ||
+          (wifi_scan_obj.currentScanMode == WIFI_SCAN_PINESCAN) ||
+          (wifi_scan_obj.currentScanMode == WIFI_SCAN_MULTISSID) ||
           (wifi_scan_obj.currentScanMode == WIFI_SCAN_ESPRESSIF) ||
           (wifi_scan_obj.currentScanMode == WIFI_SCAN_ALL) ||
           (wifi_scan_obj.currentScanMode == WIFI_SCAN_DEAUTH) ||
@@ -824,6 +848,8 @@ void MenuFunctions::main(uint32_t currentTime)
             (wifi_scan_obj.currentScanMode == WIFI_SCAN_TARGET_AP_FULL) ||
             (wifi_scan_obj.currentScanMode == WIFI_SCAN_AP_STA) ||
             (wifi_scan_obj.currentScanMode == WIFI_SCAN_PWN) ||
+            (wifi_scan_obj.currentScanMode == WIFI_SCAN_PINESCAN) ||
+            (wifi_scan_obj.currentScanMode == WIFI_SCAN_MULTISSID) ||
             (wifi_scan_obj.currentScanMode == WIFI_SCAN_ESPRESSIF) ||
             (wifi_scan_obj.currentScanMode == WIFI_SCAN_ALL) ||
             (wifi_scan_obj.currentScanMode == WIFI_SCAN_DEAUTH) ||
@@ -895,16 +921,110 @@ void MenuFunctions::main(uint32_t currentTime)
         (wifi_scan_obj.currentScanMode != WIFI_ATTACK_RICK_ROLL))
     {
       // Need this to set all keys to false
-      for (uint8_t b = 0; b < BUTTON_ARRAY_LEN; b++) {
+      /*for (uint8_t b = 0; b < BUTTON_ARRAY_LEN; b++) {
         if (pressed && display_obj.key[b].contains(t_x, t_y)) {
           display_obj.key[b].press(true);  // tell the button it is pressed
         } else {
           display_obj.key[b].press(false);  // tell the button it is NOT pressed
         }
+      }*/
+
+      // Detect up, down, select
+      uint8_t menu_button = display_obj.menuButton(&t_x, &t_y, pressed);
+
+      if (menu_button > -1) {
+        if (menu_button == UP_BUTTON) {
+          if ((wifi_scan_obj.currentScanMode == WIFI_SCAN_OFF) ||
+              (wifi_scan_obj.currentScanMode == OTA_UPDATE)) {
+            if (current_menu->selected > 0) {
+              current_menu->selected--;
+              // Page up
+              if (current_menu->selected < this->menu_start_index) {
+                this->buildButtons(current_menu, current_menu->selected);
+                this->displayCurrentMenu(current_menu->selected);
+              }
+              this->buttonSelected(current_menu->selected - this->menu_start_index, current_menu->selected);
+              if (!current_menu->list->get(current_menu->selected + 1).selected)
+                this->buttonNotSelected(current_menu->selected + 1 - this->menu_start_index, current_menu->selected + 1);
+            }
+            // Loop to end
+            else {
+              current_menu->selected = current_menu->list->size() - 1;
+              if (current_menu->selected >= BUTTON_SCREEN_LIMIT) {
+                this->buildButtons(current_menu, current_menu->selected + 1 - BUTTON_SCREEN_LIMIT);
+                this->displayCurrentMenu(current_menu->selected + 1 - BUTTON_SCREEN_LIMIT);
+              }
+              this->buttonSelected(current_menu->selected, current_menu->selected);
+              if (!current_menu->list->get(0).selected)
+                this->buttonNotSelected(0, this->menu_start_index);
+            }
+          }
+          else if ((wifi_scan_obj.currentScanMode == WIFI_PACKET_MONITOR) ||
+                  (wifi_scan_obj.currentScanMode == WIFI_SCAN_EAPOL) ||
+                  (wifi_scan_obj.currentScanMode == WIFI_SCAN_CHAN_ANALYZER) ||
+                  (wifi_scan_obj.currentScanMode == WIFI_SCAN_PACKET_RATE) ||
+                  (wifi_scan_obj.currentScanMode == WIFI_SCAN_RAW_CAPTURE) ||
+                  (wifi_scan_obj.currentScanMode == WIFI_SCAN_SIG_STREN)) {
+            if (wifi_scan_obj.set_channel < 14)
+              wifi_scan_obj.changeChannel(wifi_scan_obj.set_channel + 1);
+            else
+              wifi_scan_obj.changeChannel(1);
+          }
+        }
+        if (menu_button == DOWN_BUTTON) {
+          if ((wifi_scan_obj.currentScanMode == WIFI_SCAN_OFF) ||
+              (wifi_scan_obj.currentScanMode == OTA_UPDATE)) {
+            if (current_menu->selected < current_menu->list->size() - 1) {
+              current_menu->selected++;
+              // Page down
+              if (current_menu->selected - this->menu_start_index >= BUTTON_SCREEN_LIMIT) {
+                this->buildButtons(current_menu, current_menu->selected + 1 - BUTTON_SCREEN_LIMIT);
+                this->displayCurrentMenu(current_menu->selected + 1 - BUTTON_SCREEN_LIMIT);
+              }
+              else
+                this->buttonSelected(current_menu->selected - this->menu_start_index, current_menu->selected);
+              if (!current_menu->list->get(current_menu->selected - 1).selected)
+                this->buttonNotSelected(current_menu->selected - 1 - this->menu_start_index, current_menu->selected - 1);
+            }
+            // Loop to beginning
+            else {
+              if (current_menu->selected >= BUTTON_SCREEN_LIMIT) {
+                current_menu->selected = 0;
+                this->buildButtons(current_menu);
+                this->displayCurrentMenu();
+                this->buttonSelected(current_menu->selected);
+              }
+              else {
+                current_menu->selected = 0;
+                this->buttonSelected(current_menu->selected);
+                if (!current_menu->list->get(current_menu->list->size() - 1).selected)
+                  this->buttonNotSelected(current_menu->list->size() - 1);
+              }
+            }
+          }
+          else if ((wifi_scan_obj.currentScanMode == WIFI_PACKET_MONITOR) ||
+                  (wifi_scan_obj.currentScanMode == WIFI_SCAN_EAPOL) ||
+                  (wifi_scan_obj.currentScanMode == WIFI_SCAN_CHAN_ANALYZER) ||
+                  (wifi_scan_obj.currentScanMode == WIFI_SCAN_PACKET_RATE) ||
+                  (wifi_scan_obj.currentScanMode == WIFI_SCAN_RAW_CAPTURE) ||
+                  (wifi_scan_obj.currentScanMode == WIFI_SCAN_SIG_STREN)) {
+            if (wifi_scan_obj.set_channel > 1)
+              wifi_scan_obj.changeChannel(wifi_scan_obj.set_channel - 1);
+            else
+              wifi_scan_obj.changeChannel(14);
+          }
+        }
+        if(menu_button == SELECT_BUTTON) {
+          current_menu->list->get(current_menu->selected).callable();
+        }
+        else {
+          if (wifi_scan_obj.currentScanMode == WIFI_SCAN_OFF)
+            this->displayMenuButtons();
+        }
       }
   
       // Check if any key has changed state
-      for (uint8_t b = 0; b < current_menu->list->size(); b++) {
+      /*for (uint8_t b = 0; b < current_menu->list->size(); b++) {
         display_obj.tft.setFreeFont(MENU_FONT);
         if (display_obj.key[b].justPressed()) {
           display_obj.key[b].drawButton(true, current_menu->list->get(b).name);
@@ -938,7 +1058,7 @@ void MenuFunctions::main(uint32_t currentTime)
         }
   
         display_obj.tft.setFreeFont(NULL);
-      }
+      }*/
     }
     x = -1;
     y = -1;
@@ -946,7 +1066,7 @@ void MenuFunctions::main(uint32_t currentTime)
 
   // Menu navigation and paging
   #ifdef HAS_BUTTONS
-    #if !(defined(MARAUDER_V6) || defined(MARAUDER_V6_1))
+    #if !(defined(MARAUDER_V6) || defined(MARAUDER_V6_1) || defined(MARAUDER_CYD_MICRO) || defined(MARAUDER_CYD_GUITION) || defined(MARAUDER_CYD_2USB))
       #if !defined(MARAUDER_M5STICKC) || defined(MARAUDER_M5STICKCP2)
         if (u_btn.justPressed()){
           if ((wifi_scan_obj.currentScanMode == WIFI_SCAN_OFF) ||
@@ -1012,13 +1132,9 @@ void MenuFunctions::main(uint32_t currentTime)
             }
             else {
               current_menu->selected = 0;
-              //this->buildButtons(current_menu);  // Ensure all buttons are refreshed
-              //this->displayCurrentMenu();
               this->buttonSelected(current_menu->selected);
               if (!current_menu->list->get(current_menu->list->size() - 1).selected)
                 this->buttonNotSelected(current_menu->list->size() - 1);
-              //if (!current_menu->list->get(current_menu->list->size() - 1).selected)
-              //  this->buttonNotSelected(BUTTON_SCREEN_LIMIT - 1, current_menu->list->size() - 1);
             }
           }
         }
@@ -1158,11 +1274,13 @@ void MenuFunctions::updateStatusBar()
   
   uint16_t the_color; 
 
-  if (this->old_gps_sat_count != gps_obj.getNumSats()) {
-    this->old_gps_sat_count = gps_obj.getNumSats();
-    display_obj.tft.fillRect(0, 0, 240, STATUS_BAR_WIDTH, STATUSBAR_COLOR);
-    status_changed = true;
-  }
+  #ifdef HAS_GPS
+    if (this->old_gps_sat_count != gps_obj.getNumSats()) {
+      this->old_gps_sat_count = gps_obj.getNumSats();
+      display_obj.tft.fillRect(0, 0, 240, STATUS_BAR_WIDTH, STATUSBAR_COLOR);
+      status_changed = true;
+    }
+  #endif
 
   // GPS Stuff
   #ifdef HAS_GPS
@@ -1215,12 +1333,28 @@ void MenuFunctions::updateStatusBar()
     wifi_scan_obj.old_free_ram = wifi_scan_obj.free_ram;
     display_obj.tft.fillRect(100, 0, 60, STATUS_BAR_WIDTH, STATUSBAR_COLOR);
     #ifdef HAS_FULL_SCREEN
-      display_obj.tft.drawString((String)wifi_scan_obj.free_ram + "B", 100, 0, 2);
+    //display_obj.tft.setCursor(100, 0);
+    //display_obj.tft.setFreeFont(2);
+    //display_obj.tft.print("D:" + String(getDRAMUsagePercent()) + "%");
+    #ifndef HAS_PSRAM
+      display_obj.tft.drawString("D:" + String(getDRAMUsagePercent()) + "%", 100, 0, 2);
+    #else
+      display_obj.tft.drawString("D:" + String(getDRAMUsagePercent()) + "%" + " P:" + String(getPSRAMUsagePercent()) + "%", 100, 0, 1);
     #endif
+    //display_obj.tft.drawString((String)wifi_scan_obj.free_ram + "B", 100, 0, 2);
+  #endif
 
-    #ifdef HAS_MINI_SCREEN
-      display_obj.tft.drawString((String)wifi_scan_obj.free_ram + "B", TFT_WIDTH/1.75, 0, 1);
+  #ifdef HAS_MINI_SCREEN
+    //display_obj.tft.setCursor(TFT_WIDTH/1.75, 0);
+    //display_obj.tft.setFreeFont(1);
+    //display_obj.tft.print("D:" + String(getDRAMUsagePercent()) + "%");
+    #ifndef HAS_PSRAM
+      display_obj.tft.drawString("D:" + String(getDRAMUsagePercent()) + "%", TFT_WIDTH/1.75, 0, 1);
+    #else
+      display_obj.tft.drawString("D:" + String(getDRAMUsagePercent()) + "%" + " P:" + String(getPSRAMUsagePercent()) + "%", TFT_WIDTH/1.75, 0, 1);
     #endif
+    //display_obj.tft.drawString((String)wifi_scan_obj.free_ram + "B", TFT_WIDTH/1.75, 0, 1);
+  #endif
   }
 
   // Draw battery info
@@ -1325,11 +1459,27 @@ void MenuFunctions::drawStatusBar()
   wifi_scan_obj.old_free_ram = wifi_scan_obj.free_ram;
   display_obj.tft.fillRect(100, 0, 60, STATUS_BAR_WIDTH, STATUSBAR_COLOR);
   #ifdef HAS_FULL_SCREEN
-    display_obj.tft.drawString((String)wifi_scan_obj.free_ram + "B", 100, 0, 2);
+    //display_obj.tft.setCursor(100, 0);
+    //display_obj.tft.setFreeFont(2);
+    //display_obj.tft.print("D:" + String(getDRAMUsagePercent()) + "%");
+    #ifndef HAS_PSRAM
+      display_obj.tft.drawString("D:" + String(getDRAMUsagePercent()) + "%", 100, 0, 2);
+    #else
+      display_obj.tft.drawString("D:" + String(getDRAMUsagePercent()) + "%" + " P:" + String(getPSRAMUsagePercent()) + "%", 100, 0, 1);
+    #endif
+    //display_obj.tft.drawString((String)wifi_scan_obj.free_ram + "B", 100, 0, 2);
   #endif
 
   #ifdef HAS_MINI_SCREEN
-    display_obj.tft.drawString((String)wifi_scan_obj.free_ram + "B", TFT_WIDTH/1.75, 0, 1);
+    //display_obj.tft.setCursor(TFT_WIDTH/1.75, 0);
+    //display_obj.tft.setFreeFont(1);
+    //display_obj.tft.print("D:" + String(getDRAMUsagePercent()) + "%");
+    #ifndef HAS_PSRAM
+      display_obj.tft.drawString("D:" + String(getDRAMUsagePercent()) + "%", TFT_WIDTH/1.75, 0, 1);
+    #else
+      display_obj.tft.drawString("D:" + String(getDRAMUsagePercent()) + "%" + " P:" + String(getPSRAMUsagePercent()) + "%", TFT_WIDTH/1.75, 0, 1);
+    #endif
+    //display_obj.tft.drawString((String)wifi_scan_obj.free_ram + "B", TFT_WIDTH/1.75, 0, 1);
   #endif
 
 
@@ -1381,18 +1531,22 @@ void MenuFunctions::orientDisplay()
 {
   display_obj.tft.init();
 
-  display_obj.tft.setRotation(0); // Portrait
+  display_obj.tft.setRotation(SCREEN_ORIENTATION); // Portrait
 
   display_obj.tft.setCursor(0, 0);
 
   #ifdef HAS_ILI9341
-    #ifdef TFT_SHIELD
-      uint16_t calData[5] = { 275, 3494, 361, 3528, 4 }; // tft.setRotation(0); // Portrait with TFT Shield
-    #else if defined(TFT_DIY)
-      uint16_t calData[5] = { 339, 3470, 237, 3438, 2 }; // tft.setRotation(0); // Portrait with DIY TFT
-    #endif
+    #ifndef HAS_CYD_TOUCH
+      #ifdef TFT_SHIELD
+        uint16_t calData[5] = { 275, 3494, 361, 3528, 4 }; // tft.setRotation(0); // Portrait with TFT Shield
+      #else if defined(TFT_DIY)
+        uint16_t calData[5] = { 339, 3470, 237, 3438, 2 }; // tft.setRotation(0); // Portrait with DIY TFT
+      #endif
 
-    display_obj.tft.setTouch(calData);
+      display_obj.tft.setTouch(calData);
+    #else
+      display_obj.touchscreen.setRotation(0);
+    #endif
   #endif
 
   changeMenu(current_menu);
@@ -1492,22 +1646,22 @@ void MenuFunctions::RunSetup()
   #ifdef HAS_BT
     airtagMenu.list = new LinkedList<MenuNode>();
   #endif
-  #ifndef HAS_ILI9341
+  //#ifndef HAS_ILI9341
     wifiStationMenu.list = new LinkedList<MenuNode>();
-  #endif
+  //#endif
 
   // WiFi HTML menu stuff
   htmlMenu.list = new LinkedList<MenuNode>();
   #if (!defined(HAS_ILI9341) && defined(HAS_BUTTONS))
     miniKbMenu.list = new LinkedList<MenuNode>();
   #endif
-  #ifndef HAS_ILI9341
-    #ifdef HAS_BUTTONS
+  //#ifndef HAS_ILI9341
+  //  #ifdef HAS_BUTTONS
       #ifdef HAS_SD
         sdDeleteMenu.list = new LinkedList<MenuNode>();
       #endif
-    #endif
-  #endif
+  //  #endif
+  //#endif
 
   // Bluetooth menu stuff
   bluetoothSnifferMenu.list = new LinkedList<MenuNode>();
@@ -1561,9 +1715,9 @@ void MenuFunctions::RunSetup()
   #ifdef HAS_BT
     airtagMenu.name = "Select Airtag";
   #endif
-  #ifndef HAS_ILI9341
+  //#ifndef HAS_ILI9341
     wifiStationMenu.name = "Select Stations";
-  #endif
+  //#endif
   #ifdef HAS_GPS
     gpsInfoMenu.name = "GPS Data";
     wardrivingMenu.name = "Wardriving";
@@ -1573,9 +1727,9 @@ void MenuFunctions::RunSetup()
     miniKbMenu.name = "Mini Keyboard";
   #endif
   #ifdef HAS_SD
-    #ifndef HAS_ILI9341
+  //  #ifndef HAS_ILI9341
       sdDeleteMenu.name = "Delete SD Files";
-    #endif
+  //  #endif
   #endif
 
   // Build Main Menu
@@ -1601,9 +1755,11 @@ void MenuFunctions::RunSetup()
   this->addNodes(&wifiMenu, text_table1[31], TFTYELLOW, NULL, SNIFFERS, [this]() {
     this->changeMenu(&wifiSnifferMenu);
   });
-  this->addNodes(&wifiMenu, "Wardriving", TFTGREEN, NULL, BEACON_SNIFF, [this]() {
-    this->changeMenu(&wardrivingMenu);
-  });
+  #ifdef HAS_GPS
+    this->addNodes(&wifiMenu, "Wardriving", TFTGREEN, NULL, BEACON_SNIFF, [this]() {
+      this->changeMenu(&wardrivingMenu);
+    });
+  #endif
   this->addNodes(&wifiMenu, text_table1[32], TFTRED, NULL, ATTACKS, [this]() {
     this->changeMenu(&wifiAttackMenu);
   });
@@ -1680,25 +1836,37 @@ void MenuFunctions::RunSetup()
     this->drawStatusBar();
     wifi_scan_obj.StartScan(WIFI_SCAN_PWN, TFT_RED);
   });
-  #ifndef HAS_ILI9341
+  
+  this->addNodes(&wifiSnifferMenu, text_table1[63], TFTYELLOW, NULL, PINESCAN_SNIFF, [this]() {
+    display_obj.clearScreen();
+    this->drawStatusBar();
+    wifi_scan_obj.StartScan(WIFI_SCAN_PINESCAN, TFT_YELLOW);
+  });
+
+  this->addNodes(&wifiSnifferMenu, text_table1[64], TFTORANGE, NULL, MULTISSID_SNIFF, [this]() {
+    display_obj.clearScreen();
+    this->drawStatusBar();
+    wifi_scan_obj.StartScan(WIFI_SCAN_MULTISSID, TFT_ORANGE);
+  });
+  //#ifndef HAS_ILI9341
     this->addNodes(&wifiSnifferMenu, text_table1[49], TFTMAGENTA, NULL, BEACON_SNIFF, [this]() {
       display_obj.clearScreen();
       this->drawStatusBar();
       wifi_scan_obj.StartScan(WIFI_SCAN_TARGET_AP, TFT_MAGENTA);
     });
-  #endif
+  //#endif
   this->addNodes(&wifiSnifferMenu, "Scan All", TFTLIME, NULL, BEACON_SNIFF, [this]() {
     display_obj.clearScreen();
     this->drawStatusBar();
     wifi_scan_obj.StartScan(WIFI_SCAN_AP_STA, 0x97e0);
   });
-  #ifndef HAS_ILI9341
+  //#ifndef HAS_ILI9341
     this->addNodes(&wifiSnifferMenu, text_table1[59], TFTORANGE, NULL, PACKET_MONITOR, [this]() {
       display_obj.clearScreen();
       this->drawStatusBar();
       wifi_scan_obj.StartScan(WIFI_SCAN_STATION, TFT_WHITE);
     });
-  #endif
+  //#endif
   //#ifdef HAS_ILI9341
   this->addNodes(&wifiSnifferMenu, "Signal Monitor", TFTCYAN, NULL, PACKET_MONITOR, [this]() {
     display_obj.clearScreen();
@@ -1708,11 +1876,11 @@ void MenuFunctions::RunSetup()
   //#endif
 
   // Build Wardriving menu
-  wardrivingMenu.parentMenu = &wifiMenu; // Main Menu is second menu parent
-  this->addNodes(&wardrivingMenu, text09, TFTLIGHTGREY, NULL, 0, [this]() {
-    this->changeMenu(wardrivingMenu.parentMenu);
-  });
   #ifdef HAS_GPS
+    wardrivingMenu.parentMenu = &wifiMenu; // Main Menu is second menu parent
+    this->addNodes(&wardrivingMenu, text09, TFTLIGHTGREY, NULL, 0, [this]() {
+      this->changeMenu(wardrivingMenu.parentMenu);
+    });
     if (gps_obj.getGpsModuleStatus()) {
       this->addNodes(&wardrivingMenu, "Wardrive", TFTGREEN, NULL, BEACON_SNIFF, [this]() {
         display_obj.clearScreen();
@@ -1812,7 +1980,7 @@ void MenuFunctions::RunSetup()
     this->changeMenu(&clearAPsMenu);
     wifi_scan_obj.RunClearStations();
   });
-  #ifdef HAS_ILI9341
+  /*#ifdef HAS_ILI9341
     // Select APs on OG
     this->addNodes(&wifiGeneralMenu, text_table1[56], TFTNAVY, NULL, KEYBOARD_ICO, [this](){
       display_obj.clearScreen(); 
@@ -1837,8 +2005,8 @@ void MenuFunctions::RunSetup()
     apInfoMenu.parentMenu = &wifiGeneralMenu;
     this->addNodes(&apInfoMenu, text09, TFTLIGHTGREY, NULL, 0, [this]() {
       this->changeMenu(apInfoMenu.parentMenu);
-    });
-  #else // Mini EP HTML select
+    });*/
+  //#else // Mini EP HTML select
     this->addNodes(&wifiGeneralMenu, "Select EP HTML File", TFTCYAN, NULL, KEYBOARD_ICO, [this](){
       // Add the back button
       htmlMenu.list->clear();
@@ -1989,16 +2157,16 @@ void MenuFunctions::RunSetup()
     this->addNodes(&wifiStationMenu, text09, TFTLIGHTGREY, NULL, 0, [this]() {
       this->changeMenu(wifiStationMenu.parentMenu);
     });
-  #endif
+  //#endif
 
-  #ifdef HAS_ILI9341
-    this->addNodes(&wifiGeneralMenu, "View AP Info", TFTLIGHTGREY, NULL, 0, [this]() {
-      display_obj.clearScreen();
-      wifi_scan_obj.currentScanMode = LV_ADD_SSID;
-      wifi_scan_obj.StartScan(LV_ADD_SSID, TFT_WHITE);
-      addAPGFX("AP Info");
-    });
-  #endif
+  //#ifdef HAS_ILI9341
+  //  this->addNodes(&wifiGeneralMenu, "View AP Info", TFTLIGHTGREY, NULL, 0, [this]() {
+  //    display_obj.clearScreen();
+  //    wifi_scan_obj.currentScanMode = LV_ADD_SSID;
+  //    wifi_scan_obj.StartScan(LV_ADD_SSID, TFT_WHITE);
+  //    addAPGFX("AP Info");
+  //  });
+  //#endif
 
   this->addNodes(&wifiGeneralMenu, "Set MACs", TFTLIGHTGREY, NULL, 0, [this]() {
     this->changeMenu(&setMacMenu);
@@ -2024,7 +2192,7 @@ void MenuFunctions::RunSetup()
   });
 
   // Clone AP MAC to ESP32 for button folks
-  #ifndef HAS_ILI9341
+  //#ifndef HAS_ILI9341
     this->addNodes(&setMacMenu, "Clone AP MAC", TFTRED, NULL, CLEAR_ICO, [this](){
       // Add the back button
       wifiAPMenu.list->clear();
@@ -2060,7 +2228,7 @@ void MenuFunctions::RunSetup()
       }
       this->changeMenu(&wifiAPMenu);
     });
-  #endif
+  //#endif
 
   // Menu for generating and setting access point MAC (just goes bacK)
   genAPMacMenu.parentMenu = &wifiGeneralMenu;
@@ -2274,7 +2442,7 @@ void MenuFunctions::RunSetup()
         #ifndef HAS_ILI9341
           #ifdef HAS_BUTTONS
             this->changeMenu(&sdDeleteMenu);
-            #if !(defined(MARAUDER_V6) || defined(MARAUDER_V6_1))
+            #if !(defined(MARAUDER_V6) || defined(MARAUDER_V6_1) || defined(MARAUDER_CYD_MICRO))
 
               bool deleting = true;
 
@@ -2343,20 +2511,98 @@ void MenuFunctions::RunSetup()
               }
             #endif
           #endif
+        #else
+          #ifdef HAS_BUTTONS
+            this->changeMenu(&sdDeleteMenu);
+            bool deleting = true;
+
+            display_obj.tft.setTextWrap(false);
+            display_obj.tft.setCursor(0, SCREEN_HEIGHT / 3);
+            display_obj.tft.setTextColor(TFT_CYAN, TFT_BLACK);
+            display_obj.tft.println("Loading...");
+
+            uint16_t t_x = 0, t_y = 0; // To store the touch coordinates
+
+            while (deleting) {
+              // Build list of files
+              sd_obj.sd_files->clear();
+              delete sd_obj.sd_files;
+
+              sd_obj.sd_files = new LinkedList<String>();
+
+              sd_obj.sd_files->add("Back");
+
+              sd_obj.listDirToLinkedList(sd_obj.sd_files);
+
+              int sd_file_index = 0;
+
+              this->sdDeleteMenu.list->set(0, MenuNode{sd_obj.sd_files->get(sd_file_index), false, TFTCYAN, 0, NULL, true, NULL});
+              this->buildButtons(&sdDeleteMenu);
+              this->displayCurrentMenu();
+
+              // Start button loop
+              while(true) {
+                #ifdef HAS_ILI9341
+                  if (!this->disable_touch)
+                    pressed = display_obj.updateTouch(&t_x, &t_y);
+                #endif
+
+                uint8_t menu_button = display_obj.menuButton(&t_x, &t_y, pressed);
+
+                #if !defined(MARAUDER_M5STICKC) || defined(MARAUDER_M5STICKCP2)
+                  if (menu_button == UP_BUTTON) {
+                    if (sd_file_index > 0)
+                      sd_file_index--;
+                    else
+                      sd_file_index = sd_obj.sd_files->size() - 1;
+
+                    this->sdDeleteMenu.list->set(0, MenuNode{sd_obj.sd_files->get(sd_file_index), false, TFTCYAN, 0, NULL, true, NULL});
+                    this->buildButtons(&sdDeleteMenu);
+                    this->displayCurrentMenu();
+                  }
+                #endif
+                if (menu_button == DOWN_BUTTON) {
+                  if (sd_file_index < sd_obj.sd_files->size() - 1)
+                    sd_file_index++;
+                  else
+                    sd_file_index = 0;
+
+                  this->sdDeleteMenu.list->set(0, MenuNode{sd_obj.sd_files->get(sd_file_index), false, TFTCYAN, 0, NULL, true, NULL});
+                  this->buildButtons(&sdDeleteMenu, 0, sd_obj.sd_files->get(sd_file_index));
+                  this->displayCurrentMenu();
+                }
+                if (menu_button == SELECT_BUTTON) {
+                  if (sd_obj.sd_files->get(sd_file_index) != "Back") {
+                    if (sd_obj.removeFile("/" + sd_obj.sd_files->get(sd_file_index)))
+                      Serial.println("Successfully Removed File: /" + sd_obj.sd_files->get(sd_file_index));
+                      display_obj.tft.setTextWrap(false);
+                      display_obj.tft.setCursor(0, SCREEN_HEIGHT / 3);
+                      display_obj.tft.setTextColor(TFT_CYAN, TFT_BLACK);
+                      display_obj.tft.println("Deleting /" + sd_obj.sd_files->get(sd_file_index) + "...");
+                  }
+                  else {
+                    this->changeMenu(sdDeleteMenu.parentMenu);
+                    deleting = false;
+                  }
+                  break;
+                }
+              }
+            }
+          #endif
         #endif
       });
     }
   #endif
 
   #ifdef HAS_SD
-    #ifndef HAS_ILI9341
+    //#ifndef HAS_ILI9341
       #ifdef HAS_BUTTONS
         sdDeleteMenu.parentMenu = &deviceMenu;
         this->addNodes(&sdDeleteMenu, text09, TFTLIGHTGREY, NULL, 0, [this]() {
           this->changeMenu(sdDeleteMenu.parentMenu);
         });
       #endif
-    #endif
+    //#endif
   #endif
 
   // Save Files Menu
@@ -2539,7 +2785,7 @@ void MenuFunctions::RunSetup()
 
     // Button loop until hold center button
     #ifdef HAS_BUTTONS
-      #if !(defined(MARAUDER_V6) || defined(MARAUDER_V6_1))
+      #if !(defined(MARAUDER_V6) || defined(MARAUDER_V6_1) || defined(MARAUDER_CYD_MICRO))
         while(true) {
           // Cycle char previous
           #ifdef HAS_L
@@ -2734,12 +2980,15 @@ void MenuFunctions::setGraphScale(float scale) {
 }
 
 float MenuFunctions::calculateGraphScale(int16_t value) {
-  if (value < GRAPH_VERT_LIM) {
-    return 1.0;  // No scaling needed if the value is within the limit
+  if ((value * this->_graph_scale < GRAPH_VERT_LIM) && (value * this->_graph_scale > GRAPH_VERT_LIM * 0.75)) {
+    return this->_graph_scale;  // No scaling needed if the value is within the limit
   }
 
+  if (value < GRAPH_VERT_LIM)
+    return 1.0;
+
   // Calculate the multiplier proportionally
-  return (0.5 * GRAPH_VERT_LIM) / value;
+  return (0.75 * GRAPH_VERT_LIM) / value;
 }
 
 float MenuFunctions::graphScaleCheck(const int16_t array[TFT_WIDTH]) {
@@ -2766,7 +3015,7 @@ void MenuFunctions::drawMaxLine(int16_t value, uint16_t color) {
   display_obj.tft.setCursor(0, TFT_HEIGHT - (value * this->_graph_scale));
   display_obj.tft.setTextColor(color, TFT_BLACK);
   display_obj.tft.setTextSize(1);
-  display_obj.tft.println((String)value);
+  display_obj.tft.println((String)(value / BASE_MULTIPLIER));
 }
 
 void MenuFunctions::drawGraph(int16_t *values) {
@@ -2897,6 +3146,23 @@ void MenuFunctions::buildButtons(Menu *menu, int starting_index, String button_n
 
   }
 
+  for (int i = BUTTON_ARRAY_LEN; i < BUTTON_ARRAY_LEN + 3; i++) {
+    uint16_t x = TFT_WIDTH / 2;
+    uint16_t y = TFT_HEIGHT / 3 * (i - BUTTON_ARRAY_LEN) + ((TFT_HEIGHT / 3) / 2);
+    uint16_t w = TFT_WIDTH;
+    uint16_t h = TFT_HEIGHT / 3 - 1;
+
+    display_obj.key[i].initButton(&display_obj.tft,
+                                  x,
+                                  y, // Positioning buttons vertically
+                                  w,
+                                  h,
+                                  TFT_LIGHTGREY, // Outline
+                                  TFT_BLACK, // Fill
+                                  TFT_BLACK, // Text color
+                                  "Chicken",
+                                  1);
+  }
 }
 
 void MenuFunctions::displayCurrentMenu(int start_index)
@@ -2917,22 +3183,30 @@ void MenuFunctions::displayCurrentMenu(int start_index)
       display_obj.tft.setFreeFont(NULL);
       display_obj.tft.setTextSize(1);
     #endif
+
+    // Draw the up, down, select buttons
+    /*#ifdef HAS_ILI9341
+      for (int i = BUTTON_ARRAY_LEN; i < BUTTON_ARRAY_LEN + 3; i++) {
+        display_obj.key[i].drawButton(true);
+      }
+    #endif*/
+
     for (uint16_t i = start_index; i < min(start_index + BUTTON_SCREEN_LIMIT, current_menu->list->size()); i++)
     {
       if (!current_menu || !current_menu->list || i >= current_menu->list->size())
         continue;
       uint16_t color = this->getColor(current_menu->list->get(i).color);
       #ifdef HAS_FULL_SCREEN
-        #ifndef HAS_ILI9341
+        //#ifndef HAS_ILI9341
           if ((current_menu->list->get(i).selected) || (current_menu->selected == i)) {
             display_obj.key[i - start_index].drawButton(true, current_menu->list->get(i).name);
           }
           else {
             display_obj.key[i - start_index].drawButton(false, current_menu->list->get(i).name);          
           }
-        #else
-          display_obj.key[i].drawButton(false, current_menu->list->get(i).name); 
-        #endif
+        //#else
+        //  display_obj.key[i].drawButton(false, current_menu->list->get(i).name); 
+        //#endif
         
         if ((current_menu->list->get(i).name != text09) && (current_menu->list->get(i).icon != 255))
           display_obj.tft.drawXBitmap(0,
@@ -2954,6 +3228,8 @@ void MenuFunctions::displayCurrentMenu(int start_index)
     }
     display_obj.tft.setFreeFont(NULL);
   }
+
+  this->displayMenuButtons();
 }
 
 #endif

esp32_marauder/MenuFunctions.h

@@ -74,6 +74,8 @@ extern Settings settings_obj;
 #define DISABLE_TOUCH 34
 #define FLIPPER 35
 #define BLANK 36
+#define PINESCAN_SNIFF 37 // Use blanks icon
+#define MULTISSID_SNIFF 37 // Use blanks icon
 
 PROGMEM void my_disp_flush(lv_disp_drv_t *disp, const lv_area_t *area, lv_color_t *color_p);
 PROGMEM bool my_touchpad_read(lv_indev_drv_t * indev_driver, lv_indev_data_t * data);
@@ -170,9 +172,9 @@ class MenuFunctions
     #ifdef HAS_BT
       Menu airtagMenu;
     #endif
-    #ifndef HAS_ILI9341
+    //#ifndef HAS_ILI9341
       Menu wifiStationMenu;
-    #endif
+    //#endif
 
     // WiFi General Menu
     Menu htmlMenu;
@@ -193,7 +195,7 @@ class MenuFunctions
 
     // Menu icons
 
-
+    void displayMenuButtons();
     uint16_t getColor(uint16_t color);
     void drawAvgLine(int16_t value);
     void drawMaxLine(int16_t value, uint16_t color);
@@ -215,8 +217,6 @@ class MenuFunctions
       void miniKeyboard(Menu * targetMenu);
     #endif
 
-    uint8_t updateTouch(uint16_t *x, uint16_t *y, uint16_t threshold = 600);
-
   public:
     MenuFunctions();
 

esp32_marauder/SDInterface.cpp

@@ -21,7 +21,7 @@ bool SDInterface::initSD() {
     pinMode(SD_CS, OUTPUT);
 
     delay(10);
-    #if defined(MARAUDER_M5STICKC)
+    #if (defined(MARAUDER_M5STICKC)) || (defined(HAS_CYD_TOUCH))
       /* Set up SPI SD Card using external pin header
       StickCPlus Header - SPI SD Card Reader
                   3v3   -   3v3
@@ -31,7 +31,13 @@ bool SDInterface::initSD() {
                   G26   -   MOSI
                         -   CS (jumper to SD Card GND Pin)
       */
-      enum { SPI_SCK = 0, SPI_MISO = 36, SPI_MOSI = 26 };
+      #if defined(MARAUDER_M5STICKC)
+        enum { SPI_SCK = 0, SPI_MISO = 36, SPI_MOSI = 26 };
+      #elif defined(HAS_CYD_TOUCH)
+        enum { SPI_SCK = SD_SCK, SPI_MISO = SD_MISO, SPI_MOSI = SD_MOSI };
+      #else
+        enum { SPI_SCK = 0, SPI_MISO = 36, SPI_MOSI = 26 };
+      #endif
       this->spiExt = new SPIClass();
       this->spiExt->begin(SPI_SCK, SPI_MISO, SPI_MOSI, SD_CS);
       if (!SD.begin(SD_CS, *(this->spiExt))) {

esp32_marauder/SDInterface.h

@@ -26,9 +26,9 @@ extern Settings settings_obj;
 class SDInterface {
 
   private:
-#if defined(MARAUDER_M5STICKC)
-  SPIClass *spiExt;
-#endif
+  #if (defined(MARAUDER_M5STICKC) || defined(HAS_CYD_TOUCH))
+    SPIClass *spiExt;
+  #endif
     bool checkDetectPin();
 
   public:

esp32_marauder/WiFiScan.h

@@ -37,7 +37,7 @@
 #endif
 #include "settings.h"
 #include "Assets.h"
-#ifdef MARAUDER_FLIPPER
+#ifdef HAS_FLIPPER_LED
   #include "flipperLED.h"
 #elif defined(XIAO_ESP32_S3)
   #include "xiaoLED.h"
@@ -102,11 +102,20 @@
 #define BT_SCAN_ANALYZER 47
 #define WIFI_SCAN_PACKET_RATE 48
 #define WIFI_SCAN_AP_STA 49
+#define WIFI_SCAN_PINESCAN 50
+#define WIFI_SCAN_MULTISSID 51
 
 #define BASE_MULTIPLIER 4
 
 #define ANALYZER_NAME_REFRESH 100 // Number of events to refresh the name
 
+// PineScan and Multi SSID
+#define MULTISSID_THRESHOLD 3 // Threshold For Multi SSID
+#define MAX_MULTISSID_ENTRIES 100 // Max number of confirmed MultiSSIDs to store
+#define MAX_AP_ENTRIES 100 // Max number of APs to track for analysis
+#define MAX_DISPLAY_ENTRIES 1 // Max Unique MACs to display
+#define MAX_PINESCAN_ENTRIES 100 // PineScan Max Entries
+
 #define MAX_CHANNEL     14
 
 #define WIFI_SECURITY_OPEN   0
@@ -150,7 +159,7 @@ extern Buffer buffer_obj;
   extern BatteryInterface battery_obj;
 #endif
 extern Settings settings_obj;
-#ifdef MARAUDER_FLIPPER
+#ifdef HAS_FLIPPER_LED
   extern flipperLED flipper_led;
 #elif defined(XIAO_ESP32_S3)
   extern xiaoLED xiao_led;
@@ -201,11 +210,17 @@ struct Flipper {
   String name;
 };
 
+#ifdef HAS_PSRAM
+  extern struct mac_addr* mac_history;
+#endif
+
 class WiFiScan
 {
   private:
     // Wardriver thanks to https://github.com/JosephHewitt
-    struct mac_addr mac_history[mac_history_len];
+    #ifndef HAS_PSRAM
+      struct mac_addr mac_history[mac_history_len];
+    #endif
 
     uint8_t ap_mac[6] = {0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED};
     uint8_t sta_mac[6] = {0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED};
@@ -278,6 +293,74 @@ class WiFiScan
       WifiMgmtHdr hdr;
     } wifi_ieee80211_packet_t;
 
+		// Tracking structures for PineScan (similar to MultiSSID)
+    struct PineScanTracker {
+        uint8_t mac[6];
+        bool suspicious_oui;
+        bool tag_and_susp_cap;
+        uint8_t channel;
+        int8_t rssi;
+        bool reported;
+    };
+
+    // For confirmed Pineapple devices
+    struct ConfirmedPineScan {
+        uint8_t mac[6];
+        String detection_type;
+        String essid;
+        uint8_t channel;
+        int8_t rssi;
+        bool displayed;
+    };
+    LinkedList<PineScanTracker>* pinescan_trackers;
+    LinkedList<ConfirmedPineScan>* confirmed_pinescan;
+    bool pinescan_list_full_reported;
+    
+    // Security Conditions For Pineapple detection
+    enum SecurityCondition {
+        NONE = 0x00,
+        SUSPICIOUS_WHEN_OPEN = 0x01,
+        SUSPICIOUS_WHEN_PROTECTED = 0x02,
+        SUSPICIOUS_ALWAYS = 0x04
+    };
+
+    // SuspiciousVendor struct
+    struct SuspiciousVendor {
+        const char* vendor_name;
+        uint8_t security_flags;
+        uint32_t ouis[20];                 // Array of OUIs (max 20 per vendor)
+        uint8_t oui_count;                 // Number of OUIs for this vendor
+    };
+
+    // Declare the table for Pineapple
+    static const SuspiciousVendor suspicious_vendors[];
+    static const int NUM_SUSPICIOUS_VENDORS;
+
+    // Track for AP list limit (Uninitialised, Done in RunSetup)
+    bool ap_list_full_reported;
+
+    // MULTI SSID STRUCTS
+
+    struct MultiSSIDTracker {
+        uint8_t mac[6];
+        uint16_t ssid_hashes[MULTISSID_THRESHOLD];
+        uint8_t unique_ssid_count;
+        bool reported;
+    };
+
+    // New struct for confirmed MultiSSID devices
+    struct ConfirmedMultiSSID {
+        uint8_t mac[6];
+        String essid;
+        uint8_t channel;
+        int8_t rssi;
+        uint8_t ssid_count;
+        bool displayed;
+    };
+    LinkedList<MultiSSIDTracker>* multissid_trackers;
+    LinkedList<ConfirmedMultiSSID>* confirmed_multissid;
+    bool multissid_list_full_reported;
+
     // barebones packet
     uint8_t packet[128] = { 0x80, 0x00, 0x00, 0x00, //Frame Control, Duration
                     /*4*/   0xff, 0xff, 0xff, 0xff, 0xff, 0xff, //Destination address 
@@ -383,6 +466,8 @@ class WiFiScan
     void RunGPSNmea();
     void RunMimicFlood(uint8_t scan_mode, uint16_t color);
     void RunPwnScan(uint8_t scan_mode, uint16_t color);
+    void RunPineScan(uint8_t scan_mode, uint16_t color);
+    void RunMultiSSIDScan(uint8_t scan_mode, uint16_t color);
     void RunBeaconScan(uint8_t scan_mode, uint16_t color);
     void RunRawScan(uint8_t scan_mode, uint16_t color);
     void RunStationScan(uint8_t scan_mode, uint16_t color);
@@ -494,6 +579,8 @@ class WiFiScan
     int clearAirtags();
     int clearFlippers();
     int clearStations();
+    int clearPineScanTrackers();
+    int clearMultiSSID();
     bool addSSID(String essid);
     int generateSSIDs(int count = 20);
     bool shutdownWiFi();
@@ -546,6 +633,9 @@ class WiFiScan
     static void activeEapolSnifferCallback(void* buf, wifi_promiscuous_pkt_type_t type);
     static void eapolSnifferCallback(void* buf, wifi_promiscuous_pkt_type_t type);
     static void wifiSnifferCallback(void* buf, wifi_promiscuous_pkt_type_t type);
+    static void pineScanSnifferCallback(void* buf, wifi_promiscuous_pkt_type_t type); // Pineapple
+    static int extractPineScanChannel(const uint8_t* payload, int len); // Pineapple
+    static void multiSSIDSnifferCallback(void* buf, wifi_promiscuous_pkt_type_t type); // MultiSSID
 
     /*#ifdef HAS_BT
       enum EBLEPayloadType

esp32_marauder/configs.h

@@ -14,6 +14,7 @@
   //#define MARAUDER_V6
   //#define MARAUDER_V6_1
   //#define MARAUDER_V7
+  //#define MARAUDER_V7_1
   //#define MARAUDER_KIT
   //#define GENERIC_ESP32
   //#define MARAUDER_FLIPPER
@@ -21,9 +22,12 @@
   //#define MARAUDER_DEV_BOARD_PRO
   //#define XIAO_ESP32_S3
   //#define MARAUDER_REV_FEATHER
+  //#define MARAUDER_CYD_MICRO // 2432S028
+  //#define MARAUDER_CYD_2USB // Another 2432S028 but it has tWo UsBs OoOoOoO
+  //#define MARAUDER_CYD_GUITION // ESP32-2432S024 GUITION
   //// END BOARD TARGETS
 
-  #define MARAUDER_VERSION "v1.4.3"
+  #define MARAUDER_VERSION "v1.6.1"
 
   #define GRAPH_REFRESH   100
 
@@ -36,6 +40,8 @@
     #define HARDWARE_NAME "Marauder Mini"
   #elif defined(MARAUDER_V7)
     #define HARDWARE_NAME "Marauder v7"
+  #elif defined(MARAUDER_V7_1)
+    #define HARDWARE_NAME "Marauder v7.1"
   #elif defined(MARAUDER_REV_FEATHER)
     #define HARDWARE_NAME "Adafruit Feather ESP32-S2 Reverse TFT"
   #elif defined(MARAUDER_V4)
@@ -44,6 +50,12 @@
     #define HARDWARE_NAME "Marauder v6"
   #elif defined(MARAUDER_V6_1)
     #define HARDWARE_NAME "Marauder v6.1"
+  #elif defined(MARAUDER_CYD_MICRO)
+    #define HARDWARE_NAME "CYD 2432S028"
+  #elif defined(MARAUDER_CYD_2USB)
+    #define HARDWARE_NAME "CYD 2432S028 2USB"  
+  #elif defined(MARAUDER_CYD_GUITION)
+    #define HARDWARE_NAME "CYD 2432S024 GUITION"
   #elif defined(MARAUDER_KIT)
     #define HARDWARE_NAME "Marauder Kit"
   #elif defined(MARAUDER_FLIPPER)
@@ -107,6 +119,23 @@
     #define HAS_GPS
   #endif
 
+  #ifdef MARAUDER_V7_1
+    //#define FLIPPER_ZERO_HAT
+    #define HAS_BATTERY
+    #define HAS_BT
+    #define HAS_BT_REMOTE
+    #define HAS_BUTTONS
+    #define HAS_NEOPIXEL_LED
+    //#define HAS_PWR_MGMT
+    #define HAS_SCREEN
+    #define HAS_FULL_SCREEN
+    #define HAS_SD
+    #define USE_SD
+    #define HAS_TEMP_SENSOR
+    #define HAS_GPS
+    #define HAS_PSRAM
+  #endif
+
   #ifdef MARAUDER_REV_FEATHER
     //#define FLIPPER_ZERO_HAT
     //#define HAS_BATTERY
@@ -153,6 +182,61 @@
     #define HAS_GPS
   #endif
 
+  #ifdef MARAUDER_CYD_MICRO
+    #define HAS_FLIPPER_LED
+    //#define FLIPPER_ZERO_HAT
+    //#define HAS_BATTERY
+    #define HAS_BT
+    #define HAS_BT_REMOTE
+    #define HAS_BUTTONS
+    //#define HAS_NEOPIXEL_LED
+    //#define HAS_PWR_MGMT
+    #define HAS_SCREEN
+    #define HAS_FULL_SCREEN
+    #define HAS_SD
+    #define USE_SD
+    #define HAS_TEMP_SENSOR
+    #define HAS_GPS
+    #define HAS_CYD_TOUCH
+  #endif
+
+  #ifdef MARAUDER_CYD_2USB
+    #define HAS_FLIPPER_LED
+    //#define FLIPPER_ZERO_HAT
+    //#define HAS_BATTERY
+    #define HAS_BT
+    #define HAS_BT_REMOTE
+    #define HAS_BUTTONS
+    //#define HAS_NEOPIXEL_LED
+    //#define HAS_PWR_MGMT
+    #define HAS_SCREEN
+    #define HAS_FULL_SCREEN
+    #define HAS_SD
+    #define USE_SD
+    #define HAS_TEMP_SENSOR
+    #define HAS_GPS
+    #define HAS_CYD_TOUCH
+    #define HAS_CYD_PORTRAIT
+  #endif
+
+  #ifdef MARAUDER_CYD_GUITION
+    #define HAS_FLIPPER_LED
+    //#define FLIPPER_ZERO_HAT
+    //#define HAS_BATTERY
+    #define HAS_BT
+    #define HAS_BT_REMOTE
+    #define HAS_BUTTONS
+    //#define HAS_NEOPIXEL_LED
+    //#define HAS_PWR_MGMT
+    #define HAS_SCREEN
+    #define HAS_FULL_SCREEN
+    #define HAS_SD
+    #define USE_SD
+    #define HAS_TEMP_SENSOR
+    #define HAS_GPS
+    //#define HAS_CYD_TOUCH
+  #endif
+
   #ifdef MARAUDER_KIT
     //#define FLIPPER_ZERO_HAT
     #define HAS_BATTERY
@@ -182,6 +266,7 @@
   #endif
 
   #ifdef MARAUDER_FLIPPER
+    #define HAS_FLIPPER_LED
     //#define FLIPPER_ZERO_HAT
     //#define HAS_BATTERY
     //#define HAS_BT
@@ -192,6 +277,7 @@
     #define HAS_GPS
     #define HAS_SD
     #define USE_SD
+    #define HAS_PSRAM
     //#define HAS_TEMP_SENSOR
   #endif
 
@@ -313,6 +399,26 @@
       #define D_PULL true
     #endif
 
+    #ifdef MARAUDER_V7_1
+      #define L_BTN 13
+      #define C_BTN 34
+      #define U_BTN 36
+      #define R_BTN 39
+      #define D_BTN 35
+
+      #define HAS_L
+      #define HAS_R
+      #define HAS_U
+      #define HAS_D
+      #define HAS_C
+
+      #define L_PULL true
+      #define C_PULL true
+      #define U_PULL true
+      #define R_PULL true
+      #define D_PULL true
+    #endif
+
     #if defined(MARAUDER_M5STICKC) || defined(MARAUDER_M5STICKCP2)
       #define L_BTN -1
       #define C_BTN 37
@@ -379,6 +485,66 @@
       #define D_PULL true
     #endif  
 
+    #ifdef MARAUDER_CYD_MICRO
+      #define L_BTN -1
+      #define C_BTN 0
+      #define U_BTN -1
+      #define R_BTN -1
+      #define D_BTN -1
+
+      //#define HAS_L
+      //#define HAS_R
+      //#define HAS_U
+      //#define HAS_D
+      #define HAS_C
+
+      #define L_PULL true
+      #define C_PULL true
+      #define U_PULL true
+      #define R_PULL true
+      #define D_PULL true
+    #endif
+
+    #ifdef MARAUDER_CYD_2USB
+      #define L_BTN -1
+      #define C_BTN 0
+      #define U_BTN -1
+      #define R_BTN -1
+      #define D_BTN -1
+
+      //#define HAS_L
+      //#define HAS_R
+      //#define HAS_U
+      //#define HAS_D
+      #define HAS_C
+
+      #define L_PULL true
+      #define C_PULL true
+      #define U_PULL true
+      #define R_PULL true
+      #define D_PULL true
+    #endif
+
+    #ifdef MARAUDER_CYD_GUITION
+      #define L_BTN -1
+      #define C_BTN 0
+      #define U_BTN -1
+      #define R_BTN -1
+      #define D_BTN -1
+
+      //#define HAS_L
+      //#define HAS_R
+      //#define HAS_U
+      //#define HAS_D
+      #define HAS_C
+
+      #define L_PULL true
+      #define C_PULL true
+      #define U_PULL true
+      #define R_PULL true
+      #define D_PULL true
+    #endif
+
   #endif
   //// END BUTTON DEFINITIONS
 
@@ -415,6 +581,8 @@
 
       #define EXT_BUTTON_WIDTH 0
 
+      #define SCREEN_ORIENTATION 1
+
       #define CHAR_WIDTH 6
       #define SCREEN_WIDTH TFT_HEIGHT // Originally 240
       #define SCREEN_HEIGHT TFT_WIDTH // Originally 320
@@ -487,6 +655,8 @@
 
       #define EXT_BUTTON_WIDTH 0
 
+      #define SCREEN_ORIENTATION 0
+
       #define CHAR_WIDTH 6
       #define SCREEN_WIDTH TFT_HEIGHT // Originally 240
       #define SCREEN_HEIGHT TFT_WIDTH // Originally 320
@@ -549,6 +719,8 @@
 
       #define EXT_BUTTON_WIDTH 20
 
+      #define SCREEN_ORIENTATION 0
+
       #define CHAR_WIDTH 12
       #define SCREEN_WIDTH TFT_WIDTH
       #define SCREEN_HEIGHT TFT_HEIGHT
@@ -606,7 +778,9 @@
         #define TFT_HEIGHT 320
       #endif
 
-      #define TFT_DIY
+      #ifndef MARAUDER_CYD_MICRO
+        #define TFT_DIY
+      #endif
 
       #define GRAPH_VERT_LIM TFT_HEIGHT/2
 
@@ -615,6 +789,8 @@
       #define SCREEN_BUFFER
 
       #define MAX_SCREEN_BUFFER 22
+
+      #define SCREEN_ORIENTATION 0
     
       #define CHAR_WIDTH 12
       #define SCREEN_WIDTH TFT_WIDTH
@@ -659,6 +835,210 @@
       #define KIT_LED_BUILTIN 13
     #endif 
 
+    #if defined(MARAUDER_CYD_MICRO)
+      #define SCREEN_CHAR_WIDTH 40
+      #define HAS_ILI9341
+    
+      #define BANNER_TEXT_SIZE 2
+
+      #ifndef TFT_WIDTH
+        #define TFT_WIDTH 240
+      #endif
+
+      #ifndef TFT_HEIGHT
+        #define TFT_HEIGHT 320
+      #endif
+
+      #define GRAPH_VERT_LIM TFT_HEIGHT/2
+
+      #define EXT_BUTTON_WIDTH 20
+
+      #define SCREEN_BUFFER
+
+      #define MAX_SCREEN_BUFFER 22
+
+      #define SCREEN_ORIENTATION 0
+    
+      #define CHAR_WIDTH 12
+      #define SCREEN_WIDTH TFT_WIDTH
+      #define SCREEN_HEIGHT TFT_HEIGHT
+      #define HEIGHT_1 TFT_WIDTH
+      #define WIDTH_1 TFT_HEIGHT
+      #define STANDARD_FONT_CHAR_LIMIT (TFT_WIDTH/6) // number of characters on a single line with normal font
+      #define TEXT_HEIGHT 16 // Height of text to be printed and scrolled
+      #define BOT_FIXED_AREA 0 // Number of lines in bottom fixed area (lines counted from bottom of screen)
+      #define TOP_FIXED_AREA 48 // Number of lines in top fixed area (lines counted from top of screen)
+      #define YMAX 320 // Bottom of screen area
+      #define minimum(a,b)     (((a) < (b)) ? (a) : (b))
+      //#define MENU_FONT NULL
+      #define MENU_FONT &FreeMono9pt7b // Winner
+      //#define MENU_FONT &FreeMonoBold9pt7b
+      //#define MENU_FONT &FreeSans9pt7b
+      //#define MENU_FONT &FreeSansBold9pt7b
+      #define BUTTON_SCREEN_LIMIT 12
+      #define BUTTON_ARRAY_LEN BUTTON_SCREEN_LIMIT
+      #define STATUS_BAR_WIDTH 16
+      #define LVGL_TICK_PERIOD 6
+
+      #define FRAME_X 100
+      #define FRAME_Y 64
+      #define FRAME_W 120
+      #define FRAME_H 50
+    
+      // Red zone size
+      #define REDBUTTON_X FRAME_X
+      #define REDBUTTON_Y FRAME_Y
+      #define REDBUTTON_W (FRAME_W/2)
+      #define REDBUTTON_H FRAME_H
+    
+      // Green zone size
+      #define GREENBUTTON_X (REDBUTTON_X + REDBUTTON_W)
+      #define GREENBUTTON_Y FRAME_Y
+      #define GREENBUTTON_W (FRAME_W/2)
+      #define GREENBUTTON_H FRAME_H
+    
+      #define STATUSBAR_COLOR 0x4A49
+    
+      #define KIT_LED_BUILTIN 13
+    #endif
+
+    #if defined(MARAUDER_CYD_2USB)
+      #define SCREEN_CHAR_WIDTH 40
+      #define HAS_ILI9341
+      #define HAS_ST7789
+    
+      #define BANNER_TEXT_SIZE 2
+
+      #ifndef TFT_WIDTH
+        #define TFT_WIDTH 240
+      #endif
+
+      #ifndef TFT_HEIGHT
+        #define TFT_HEIGHT 320
+      #endif
+
+      #define GRAPH_VERT_LIM TFT_HEIGHT/2
+
+      #define EXT_BUTTON_WIDTH 20
+
+      #define SCREEN_BUFFER
+
+      #define MAX_SCREEN_BUFFER 22
+
+      #define SCREEN_ORIENTATION 0
+    
+      #define CHAR_WIDTH 12
+      #define SCREEN_WIDTH TFT_WIDTH
+      #define SCREEN_HEIGHT TFT_HEIGHT
+      #define HEIGHT_1 TFT_WIDTH
+      #define WIDTH_1 TFT_HEIGHT
+      #define STANDARD_FONT_CHAR_LIMIT (TFT_WIDTH/6) // number of characters on a single line with normal font
+      #define TEXT_HEIGHT 16 // Height of text to be printed and scrolled
+      #define BOT_FIXED_AREA 0 // Number of lines in bottom fixed area (lines counted from bottom of screen)
+      #define TOP_FIXED_AREA 48 // Number of lines in top fixed area (lines counted from top of screen)
+      #define YMAX 320 // Bottom of screen area
+      #define minimum(a,b)     (((a) < (b)) ? (a) : (b))
+      //#define MENU_FONT NULL
+      #define MENU_FONT &FreeMono9pt7b // Winner
+      //#define MENU_FONT &FreeMonoBold9pt7b
+      //#define MENU_FONT &FreeSans9pt7b
+      //#define MENU_FONT &FreeSansBold9pt7b
+      #define BUTTON_SCREEN_LIMIT 12
+      #define BUTTON_ARRAY_LEN BUTTON_SCREEN_LIMIT
+      #define STATUS_BAR_WIDTH 16
+      #define LVGL_TICK_PERIOD 6
+
+      #define FRAME_X 100
+      #define FRAME_Y 64
+      #define FRAME_W 120
+      #define FRAME_H 50
+    
+      // Red zone size
+      #define REDBUTTON_X FRAME_X
+      #define REDBUTTON_Y FRAME_Y
+      #define REDBUTTON_W (FRAME_W/2)
+      #define REDBUTTON_H FRAME_H
+    
+      // Green zone size
+      #define GREENBUTTON_X (REDBUTTON_X + REDBUTTON_W)
+      #define GREENBUTTON_Y FRAME_Y
+      #define GREENBUTTON_W (FRAME_W/2)
+      #define GREENBUTTON_H FRAME_H
+    
+      #define STATUSBAR_COLOR 0x4A49
+    
+      #define KIT_LED_BUILTIN 13
+    #endif
+
+    #if defined(MARAUDER_CYD_GUITION)
+      #define SCREEN_CHAR_WIDTH 40
+      #define HAS_ILI9341
+    
+      #define BANNER_TEXT_SIZE 2
+
+      #ifndef TFT_WIDTH
+        #define TFT_WIDTH 240
+      #endif
+
+      #ifndef TFT_HEIGHT
+        #define TFT_HEIGHT 320
+      #endif
+
+      #define TFT_DIY
+
+      #define GRAPH_VERT_LIM TFT_HEIGHT/2
+
+      #define EXT_BUTTON_WIDTH 20
+
+      #define SCREEN_BUFFER
+
+      #define MAX_SCREEN_BUFFER 22
+
+      #define SCREEN_ORIENTATION 0
+    
+      #define CHAR_WIDTH 12
+      #define SCREEN_WIDTH TFT_WIDTH
+      #define SCREEN_HEIGHT TFT_HEIGHT
+      #define HEIGHT_1 TFT_WIDTH
+      #define WIDTH_1 TFT_HEIGHT
+      #define STANDARD_FONT_CHAR_LIMIT (TFT_WIDTH/6) // number of characters on a single line with normal font
+      #define TEXT_HEIGHT 16 // Height of text to be printed and scrolled
+      #define BOT_FIXED_AREA 0 // Number of lines in bottom fixed area (lines counted from bottom of screen)
+      #define TOP_FIXED_AREA 48 // Number of lines in top fixed area (lines counted from top of screen)
+      #define YMAX 320 // Bottom of screen area
+      #define minimum(a,b)     (((a) < (b)) ? (a) : (b))
+      //#define MENU_FONT NULL
+      #define MENU_FONT &FreeMono9pt7b // Winner
+      //#define MENU_FONT &FreeMonoBold9pt7b
+      //#define MENU_FONT &FreeSans9pt7b
+      //#define MENU_FONT &FreeSansBold9pt7b
+      #define BUTTON_SCREEN_LIMIT 12
+      #define BUTTON_ARRAY_LEN BUTTON_SCREEN_LIMIT
+      #define STATUS_BAR_WIDTH 16
+      #define LVGL_TICK_PERIOD 6
+
+      #define FRAME_X 100
+      #define FRAME_Y 64
+      #define FRAME_W 120
+      #define FRAME_H 50
+    
+      // Red zone size
+      #define REDBUTTON_X FRAME_X
+      #define REDBUTTON_Y FRAME_Y
+      #define REDBUTTON_W (FRAME_W/2)
+      #define REDBUTTON_H FRAME_H
+    
+      // Green zone size
+      #define GREENBUTTON_X (REDBUTTON_X + REDBUTTON_W)
+      #define GREENBUTTON_Y FRAME_Y
+      #define GREENBUTTON_W (FRAME_W/2)
+      #define GREENBUTTON_H FRAME_H
+    
+      #define STATUSBAR_COLOR 0x4A49
+    
+      #define KIT_LED_BUILTIN 13
+    #endif
+
     #ifdef MARAUDER_V7
       #define SCREEN_CHAR_WIDTH 40
       //#define HAS_ILI9341
@@ -682,6 +1062,77 @@
       #define MAX_SCREEN_BUFFER 22
 
       #define EXT_BUTTON_WIDTH 0
+
+      #define SCREEN_ORIENTATION 0
+    
+      #define CHAR_WIDTH 12
+      #define SCREEN_WIDTH TFT_WIDTH
+      #define SCREEN_HEIGHT TFT_HEIGHT
+      #define HEIGHT_1 TFT_WIDTH
+      #define WIDTH_1 TFT_HEIGHT
+      #define STANDARD_FONT_CHAR_LIMIT (TFT_WIDTH/6) // number of characters on a single line with normal font
+      #define TEXT_HEIGHT 16 // Height of text to be printed and scrolled
+      #define BOT_FIXED_AREA 0 // Number of lines in bottom fixed area (lines counted from bottom of screen)
+      #define TOP_FIXED_AREA 48 // Number of lines in top fixed area (lines counted from top of screen)
+      #define YMAX 320 // Bottom of screen area
+      #define minimum(a,b)     (((a) < (b)) ? (a) : (b))
+      //#define MENU_FONT NULL
+      #define MENU_FONT &FreeMono9pt7b // Winner
+      //#define MENU_FONT &FreeMonoBold9pt7b
+      //#define MENU_FONT &FreeSans9pt7b
+      //#define MENU_FONT &FreeSansBold9pt7b
+      #define BUTTON_SCREEN_LIMIT 12
+      #define BUTTON_ARRAY_LEN BUTTON_SCREEN_LIMIT
+      #define STATUS_BAR_WIDTH 16
+      #define LVGL_TICK_PERIOD 6
+
+      #define FRAME_X 100
+      #define FRAME_Y 64
+      #define FRAME_W 120
+      #define FRAME_H 50
+    
+      // Red zone size
+      #define REDBUTTON_X FRAME_X
+      #define REDBUTTON_Y FRAME_Y
+      #define REDBUTTON_W (FRAME_W/2)
+      #define REDBUTTON_H FRAME_H
+    
+      // Green zone size
+      #define GREENBUTTON_X (REDBUTTON_X + REDBUTTON_W)
+      #define GREENBUTTON_Y FRAME_Y
+      #define GREENBUTTON_W (FRAME_W/2)
+      #define GREENBUTTON_H FRAME_H
+    
+      #define STATUSBAR_COLOR 0x4A49
+    
+      #define KIT_LED_BUILTIN 13
+    #endif
+
+    #ifdef MARAUDER_V7_1
+      #define SCREEN_CHAR_WIDTH 40
+      //#define HAS_ILI9341
+    
+      #define BANNER_TEXT_SIZE 2
+
+      #ifndef TFT_WIDTH
+        #define TFT_WIDTH 240
+      #endif
+
+      #ifndef TFT_HEIGHT
+        #define TFT_HEIGHT 320
+      #endif
+
+      #define GRAPH_VERT_LIM TFT_HEIGHT/2
+
+      #define TFT_DIY
+
+      #define SCREEN_BUFFER
+
+      #define MAX_SCREEN_BUFFER 22
+
+      #define EXT_BUTTON_WIDTH 0
+
+      #define SCREEN_ORIENTATION 0
     
       #define CHAR_WIDTH 12
       #define SCREEN_WIDTH TFT_WIDTH
@@ -746,6 +1197,8 @@
       #define KIT
 
       #define EXT_BUTTON_WIDTH 20
+
+      #define SCREEN_ORIENTATION 0
     
       #define CHAR_WIDTH 12
       #define SCREEN_WIDTH TFT_WIDTH
@@ -820,6 +1273,8 @@
 
       #define EXT_BUTTON_WIDTH 0
 
+      #define SCREEN_ORIENTATION 0
+
       #define CHAR_WIDTH 6
       #define SCREEN_WIDTH TFT_WIDTH // Originally 240
       #define SCREEN_HEIGHT TFT_HEIGHT // Originally 320
@@ -891,6 +1346,8 @@
 
       #define EXT_BUTTON_WIDTH 0
 
+      #define SCREEN_ORIENTATION 1
+
       #define CHAR_WIDTH 6
       #define SCREEN_WIDTH TFT_WIDTH // Originally 240
       #define SCREEN_HEIGHT TFT_HEIGHT // Originally 320
@@ -974,6 +1431,63 @@
     //#define BUTTON_ARRAY_LEN 5
   #endif
 
+  #if defined(MARAUDER_CYD_MICRO)
+    #define BANNER_TIME 100
+    
+    #define COMMAND_PREFIX "!"
+    
+    // Keypad start position, key sizes and spacing
+    #define KEY_X 120 // Centre of key
+    #define KEY_Y 50
+    #define KEY_W 240 // Width and height
+    #define KEY_H 22
+    #define KEY_SPACING_X 0 // X and Y gap
+    #define KEY_SPACING_Y 1
+    #define KEY_TEXTSIZE 1   // Font size multiplier
+    #define ICON_W 22
+    #define ICON_H 22
+    #define BUTTON_PADDING 22
+    //#define BUTTON_ARRAY_LEN 5
+  #endif
+
+  #if defined(MARAUDER_CYD_2USB)
+    #define BANNER_TIME 100
+    
+    #define COMMAND_PREFIX "!"
+    
+    // Keypad start position, key sizes and spacing
+    #define KEY_X 120 // Centre of key
+    #define KEY_Y 50
+    #define KEY_W 240 // Width and height
+    #define KEY_H 22
+    #define KEY_SPACING_X 0 // X and Y gap
+    #define KEY_SPACING_Y 1
+    #define KEY_TEXTSIZE 1   // Font size multiplier
+    #define ICON_W 22
+    #define ICON_H 22
+    #define BUTTON_PADDING 22
+    //#define BUTTON_ARRAY_LEN 5
+  #endif
+
+  #if defined(MARAUDER_CYD_GUITION)
+    #define BANNER_TIME 100
+    
+    #define COMMAND_PREFIX "!"
+    
+    // Keypad start position, key sizes and spacing
+    #define KEY_X 120 // Centre of key
+    #define KEY_Y 50
+    #define KEY_W 240 // Width and height
+    #define KEY_H 22
+    #define KEY_SPACING_X 0 // X and Y gap
+    #define KEY_SPACING_Y 1
+    #define KEY_TEXTSIZE 1   // Font size multiplier
+    #define ICON_W 22
+    #define ICON_H 22
+    #define BUTTON_PADDING 22
+    //#define BUTTON_ARRAY_LEN 5
+  #endif
+
   #ifdef MARAUDER_V7
     #define BANNER_TIME 100
     
@@ -993,6 +1507,25 @@
     //#define BUTTON_ARRAY_LEN 5
   #endif
 
+  #ifdef MARAUDER_V7_1
+    #define BANNER_TIME 100
+    
+    #define COMMAND_PREFIX "!"
+    
+    // Keypad start position, key sizes and spacing
+    #define KEY_X 120 // Centre of key
+    #define KEY_Y 50
+    #define KEY_W 240 // Width and height
+    #define KEY_H 22
+    #define KEY_SPACING_X 0 // X and Y gap
+    #define KEY_SPACING_Y 1
+    #define KEY_TEXTSIZE 1   // Font size multiplier
+    #define ICON_W 22
+    #define ICON_H 22
+    #define BUTTON_PADDING 22
+    //#define BUTTON_ARRAY_LEN 5
+  #endif
+
   #ifdef MARAUDER_KIT
     #define BANNER_TIME 100
     
@@ -1082,6 +1615,18 @@
       #define SD_CS 14
     #endif
 
+    #ifdef MARAUDER_CYD_MICRO
+      #define SD_CS 5
+    #endif
+
+    #ifdef MARAUDER_CYD_2USB
+      #define SD_CS 5
+    #endif
+
+    #ifdef MARAUDER_CYD_GUITION
+      #define SD_CS 5
+    #endif
+
     #ifdef MARAUDER_KIT
       #define SD_CS 12
     #endif
@@ -1094,6 +1639,10 @@
       #define SD_CS 4
     #endif
 
+    #ifdef MARAUDER_V7_1
+      #define SD_CS 4
+    #endif
+
     #ifdef MARAUDER_REV_FEATHER
       #define SD_CS 5
     #endif
@@ -1142,6 +1691,8 @@
   #define TFTLIME      18
   //// END SPACE SAVING COLORS
 
+  #define TFT_FARTGRAY 0x528a
+
   //// SCREEN STUFF
   #ifndef HAS_SCREEN
 
@@ -1178,12 +1729,20 @@
     #define MEM_LOWER_LIM 10000
   #elif defined(MARAUDER_V7)
     #define MEM_LOWER_LIM 10000
+  #elif defined(MARAUDER_V7_1)
+    #define MEM_LOWER_LIM 10000
   #elif defined(MARAUDER_REV_FEATHER)
     #define MEM_LOWER_LIM 10000
   #elif defined(MARAUDER_V4)
     #define MEM_LOWER_LIM 10000
   #elif defined(MARAUDER_V6) || defined(MARAUDER_V6_1)
     #define MEM_LOWER_LIM 10000
+  #elif defined(MARAUDER_CYD_MICRO)
+    #define MEM_LOWER_LIM 10000
+  #elif defined(MARAUDER_CYD_2USB)
+    #define MEM_LOWER_LIM 10000
+  #elif defined(MARAUDER_CYD_GUITION)
+    #define MEM_LOWER_LIM 10000
   #elif defined(MARAUDER_KIT)
     #define MEM_LOWER_LIM 10000
   #elif defined(GENERIC_ESP32)
@@ -1208,6 +1767,10 @@
       #define PIN 16
     #elif defined(MARAUDER_REV_FEATHER)
       #define PIN 33
+    #elif defined(MARAUDER_CYD_MICRO)
+      #define PIN 4
+    #elif defined(MARAUDER_CYD_2USB)
+      #define PIN 4
     #else
       #define PIN 25
     #endif
@@ -1216,82 +1779,75 @@
   //// END NEOPIXEL STUFF
 
   //// EVIL PORTAL STUFF
-  #ifdef MARAUDER_M5STICKC
-    #define MAX_HTML_SIZE 11400
-  #elif defined(MARAUDER_MINI)
-    #define MAX_HTML_SIZE 11400
-  #elif defined(MARAUDER_V7)
-    #define MAX_HTML_SIZE 11400
-  #elif defined(MARAUDER_REV_FEATHER)
-    #define MAX_HTML_SIZE 11400
-  #elif defined(MARAUDER_V4)
-    #define MAX_HTML_SIZE 11400
-  #elif defined(MARAUDER_V6) || defined(MARAUDER_V6_1)
-    #define MAX_HTML_SIZE 11400
-  #elif defined(MARAUDER_KIT)
-    #define MAX_HTML_SIZE 11400
-  #elif defined(GENERIC_ESP32)
-    #define MAX_HTML_SIZE 20000
-  #elif defined(MARAUDER_FLIPPER)
-    #define MAX_HTML_SIZE 20000
-  #elif defined(ESP32_LDDB)
-    #define MAX_HTML_SIZE 20000
-  #elif defined(MARAUDER_DEV_BOARD_PRO)
-    #define MAX_HTML_SIZE 20000
-  #elif defined(XIAO_ESP32_S3)
-    #define MAX_HTML_SIZE 20000
+
+  #ifdef HAS_PSRAM
+    #define MAX_HTML_SIZE 30000
   #else
-    #define MAX_HTML_SIZE 20000
+    #define MAX_HTML_SIZE 11400
   #endif
+
   //// END EVIL PORTAL STUFF
 
   //// GPS STUFF
   #ifdef HAS_GPS
+    #ifdef HAS_PSRAM
+      #define mac_history_len 500
+    #else
+      #define mac_history_len 100
+    #endif
+
     #if defined(MARAUDER_V6) || defined(MARAUDER_V6_1)
       #define GPS_SERIAL_INDEX 2
       #define GPS_TX 4
       #define GPS_RX 13
-      #define mac_history_len 100
+    #elif defined(MARAUDER_CYD_MICRO)
+      #define GPS_SERIAL_INDEX 2
+      #define GPS_TX 27 // Fits the extended I/O
+      #define GPS_RX 22
+    #elif defined(MARAUDER_CYD_2USB)
+      #define GPS_SERIAL_INDEX 2
+      #define GPS_TX 27 // Fits the extended I/O
+      #define GPS_RX 22
+    #elif defined(MARAUDER_CYD_GUITION)
+      #define GPS_SERIAL_INDEX 2
+      #define GPS_TX 21 // Fits the extended I/O
+      #define GPS_RX 22
     #elif defined(MARAUDER_V4)
       #define GPS_SERIAL_INDEX 2
       #define GPS_TX 4
       #define GPS_RX 13
-      #define mac_history_len 100
     #elif defined(MARAUDER_KIT)
       #define GPS_SERIAL_INDEX 2
       #define GPS_TX 4
       #define GPS_RX 13
-      #define mac_history_len 100
     #elif defined(MARAUDER_DEV_BOARD_PRO)
       #define GPS_SERIAL_INDEX 2
       #define GPS_TX 21
       #define GPS_RX 17
-      #define mac_history_len 100
     #elif defined(MARAUDER_MINI)
       #define GPS_SERIAL_INDEX 2
       #define GPS_TX 21
       #define GPS_RX 22
-      #define mac_history_len 100
     #elif defined(MARAUDER_V7)
       #define GPS_SERIAL_INDEX 2
       #define GPS_TX 21
       #define GPS_RX 22
-      #define mac_history_len 100
+    #elif defined(MARAUDER_V7_1)
+      #define GPS_SERIAL_INDEX 2
+      #define GPS_TX 21
+      #define GPS_RX 22
     #elif defined(MARAUDER_FLIPPER)
       #define GPS_SERIAL_INDEX 1
       #define GPS_TX 9
       #define GPS_RX 21
-      #define mac_history_len 100
     #elif defined(MARAUDER_M5STICKC)
       #define GPS_SERIAL_INDEX 1
       #define GPS_TX 33
       #define GPS_RX 32
-      #define mac_history_len 100
     #elif defined(MARAUDER_REV_FEATHER)
       #define GPS_SERIAL_INDEX 1
       #define GPS_TX 6
       #define GPS_RX 9
-      #define mac_history_len 100
     #endif
   #else
     #define mac_history_len 100
@@ -1336,6 +1892,11 @@
       #define I2C_SCL 16
     #endif
 
+    #ifdef MARAUDER_V7_1
+      #define I2C_SDA 33
+      #define I2C_SCL 27
+    #endif
+
   #endif
 
   //// MARAUDER TITLE STUFF
@@ -1343,12 +1904,20 @@
     #define MARAUDER_TITLE_BYTES 13578
   #elif defined(MARAUDER_V6) || defined(MARAUDER_V6_1)
     #define MARAUDER_TITLE_BYTES 13578
+  #elif defined(MARAUDER_CYD_MICRO)
+    #define MARAUDER_TITLE_BYTES 13578
+  #elif defined(MARAUDER_CYD_2USB)
+    #define MARAUDER_TITLE_BYTES 13578
+  #elif defined(MARAUDER_CYD_GUITION)
+    #define MARAUDER_TITLE_BYTES 13578
   #elif defined(MARAUDER_KIT)
     #define MARAUDER_TITLE_BYTES 13578
   #elif defined(MARAUDER_MINI)
     #define MARAUDER_TITLE_BYTES 13578
   #elif defined(MARAUDER_V7)
     #define MARAUDER_TITLE_BYTES 13578
+  #elif defined(MARAUDER_V7_1)
+    #define MARAUDER_TITLE_BYTES 13578
   #elif defined(MARAUDER_REV_FEATHER)
     #define MARAUDER_TITLE_BYTES 13578
   #else
@@ -1357,19 +1926,75 @@
   //// END MARAUDER TITLE STUFF
 
   //// PCAP BUFFER STUFF
-
-  #ifdef MARAUDER_V7
+  
+  #ifdef HAS_PSRAM
     #define BUF_SIZE 8 * 1024 // Had to reduce buffer size to save RAM. GG @spacehuhn
-    #define SNAP_LEN 4096 // max len of each recieved packet
-  #elif defined(MARAUDER_MINI)
-    #define BUF_SIZE 8 * 1024 // Had to reduce buffer size to save RAM. GG @spacehuhn
-    #define SNAP_LEN 4096 // max len of each recieved packet
-  #elif defined(MARAUDER_REV_FEATHER)
+    #define SNAP_LEN 1 * 4096 // max len of each recieved packet
+  #elif !defined(HAS_ILI9341)
     #define BUF_SIZE 8 * 1024 // Had to reduce buffer size to save RAM. GG @spacehuhn
     #define SNAP_LEN 4096 // max len of each recieved packet
   #else
     #define BUF_SIZE 3 * 1024 // Had to reduce buffer size to save RAM. GG @spacehuhn
     #define SNAP_LEN 2324 // max len of each recieved packet
   #endif
+
   //// PCAP BUFFER STUFF
+
+  //// STUPID CYD STUFF
+  #ifdef HAS_CYD_TOUCH
+    #ifdef MARAUDER_CYD_MICRO
+      #define XPT2046_IRQ  36
+      #define XPT2046_MOSI 32
+      #define XPT2046_MISO 39
+      #define XPT2046_CLK  25
+      #define XPT2046_CS   33
+
+      #define SD_MISO      19
+      #define SD_MOSI      23
+      #define SD_SCK       18
+    #endif
+
+    #ifdef MARAUDER_CYD_2USB
+      #define XPT2046_IRQ  36
+      #define XPT2046_MOSI 32
+      #define XPT2046_MISO 39
+      #define XPT2046_CLK  25
+      #define XPT2046_CS   33
+
+      #define SD_MISO      19
+      #define SD_MOSI      23
+      #define SD_SCK       18
+    #endif
+  #endif
+  //// END STUPID CYD STUFF
+
+  //// FUNNY FLIPPER LED STUFF
+
+  #ifdef HAS_FLIPPER_LED
+    #ifdef MARAUDER_FLIPPER
+      #define B_PIN 4
+      #define G_PIN 5
+      #define R_PIN 6
+    #endif
+
+    #ifdef MARAUDER_CYD_MICRO
+      #define B_PIN 17
+      #define G_PIN 16
+      #define R_PIN 4
+    #endif
+
+    #ifdef MARAUDER_CYD_2USB
+      #define B_PIN 17
+      #define G_PIN 16
+      #define R_PIN 4
+    #endif
+
+    #ifdef MARAUDER_CYD_GUITION
+      #define B_PIN 17
+      #define G_PIN 16
+      #define R_PIN 4
+    #endif
+  #endif
+
+  //// END FUNNY FLIPPER LED STUFF
 #endif

esp32_marauder/esp32_marauder.ino

@@ -34,7 +34,7 @@ https://www.online-utility.org/image/convert/to/XBM
 #endif
 #include "Buffer.h"
 
-#ifdef MARAUDER_FLIPPER
+#ifdef HAS_FLIPPER_LED
   #include "flipperLED.h"
 #elif defined(XIAO_ESP32_S3)
   #include "xiaoLED.h"
@@ -105,7 +105,7 @@ CommandLine cli_obj;
   AXP192 axp192_obj;
 #endif
 
-#ifdef MARAUDER_FLIPPER
+#ifdef HAS_FLIPPER_LED
   flipperLED flipper_led;
 #elif defined(XIAO_ESP32_S3)
   xiaoLED xiao_led;
@@ -123,7 +123,6 @@ const String PROGMEM version_number = MARAUDER_VERSION;
 
 uint32_t currentTime  = 0;
 
-
 void backlightOn() {
   #ifdef HAS_SCREEN
     #ifdef MARAUDER_MINI
@@ -166,10 +165,10 @@ void setup()
   #endif
   
   backlightOff();
-#if BATTERY_ANALOG_ON == 1
-  pinMode(BATTERY_PIN, OUTPUT);
-  pinMode(CHARGING_PIN, INPUT);
-#endif
+  #if BATTERY_ANALOG_ON == 1
+    pinMode(BATTERY_PIN, OUTPUT);
+    pinMode(CHARGING_PIN, INPUT);
+  #endif
   
   // Preset SPI CS pins to avoid bus conflicts
   #ifdef HAS_SCREEN
@@ -193,6 +192,14 @@ void setup()
 
   Serial.println("ESP-IDF version is: " + String(esp_get_idf_version()));
 
+  #ifdef HAS_PSRAM
+    if (psramInit()) {
+      Serial.println("PSRAM is correctly initialized");
+    } else {
+      Serial.println("PSRAM not available");
+    }
+  #endif
+
   #ifdef HAS_SCREEN
     display_obj.RunSetup();
     display_obj.tft.setTextColor(TFT_WHITE, TFT_BLACK);
@@ -258,18 +265,9 @@ void setup()
   buffer_obj = Buffer();
   #if defined(HAS_SD)
     // Do some SD stuff
-    if(sd_obj.initSD()) {
-      #ifdef HAS_SCREEN
-        //display_obj.tft.println(F(text_table0[3]));
-      #endif
-    } else {
+    if(!sd_obj.initSD())
       Serial.println(F("SD Card NOT Supported"));
-      #ifdef HAS_SCREEN
-        //display_obj.tft.setTextColor(TFT_RED, TFT_BLACK);
-        //display_obj.tft.println(F(text_table0[4]));
-        //display_obj.tft.setTextColor(TFT_CYAN, TFT_BLACK);
-      #endif
-    }
+
   #endif
 
   #ifdef HAS_SCREEN
@@ -296,7 +294,7 @@ void setup()
   #endif
 
   // Do some LED stuff
-  #ifdef MARAUDER_FLIPPER
+  #ifdef HAS_FLIPPER_LED
     flipper_led.RunSetup();
   #elif defined(XIAO_ESP32_S3)
     xiao_led.RunSetup();
@@ -352,7 +350,7 @@ void loop()
     #endif
   #endif
 
-  #ifdef HAS_ILI9341
+  #if (defined(HAS_ILI9341) && !defined(MARAUDER_CYD_2USB))
     #ifdef HAS_BUTTONS
       if (c_btn.isHeld()) {
         if (menu_function_obj.disable_touch)
@@ -397,7 +395,7 @@ void loop()
       menu_function_obj.main(currentTime);
     #endif
   }
-  #ifdef MARAUDER_FLIPPER
+  #ifdef HAS_FLIPPER_LED
     flipper_led.main();
   #elif defined(XIAO_ESP32_S3)
     xiao_led.main();

esp32_marauder/flipperLED.cpp

@@ -1,5 +1,7 @@
 #include "flipperLED.h"
 
+#ifdef HAS_FLIPPER_LED
+
 void flipperLED::RunSetup() {
   pinMode(B_PIN, OUTPUT);
   pinMode(G_PIN, OUTPUT);
@@ -58,4 +60,6 @@ void flipperLED::offLED() {
 
 void flipperLED::main() {
   // do nothing
-}
+}
+
+#endif

esp32_marauder/flipperLED.h

@@ -8,10 +8,6 @@
 
 #include <Arduino.h>
 
-#define B_PIN 4
-#define G_PIN 5
-#define R_PIN 6
-
 extern Settings settings_obj;
 
 class flipperLED {

esp32_marauder/lang_var.h

@@ -103,7 +103,8 @@ PROGMEM const char text1_59[] = "Station Sniff";
 PROGMEM const char text1_60[] = "Clear Stations";
 PROGMEM const char text1_61[] = "Select Stations";
 PROGMEM const char text1_62[] = "Deauth Targeted";
-
+PROGMEM const char text1_63[] = "Detect Pineapple";
+PROGMEM const char text1_64[] = "Detect MultiSSID";
 
 //SDInterface.cpp texts
 PROGMEM const char text2_0[] = "Error, could not find update.bin";
@@ -179,12 +180,14 @@ PROGMEM const char text4_44[] = " AP Scan ";
 PROGMEM const char text4_45[] = "Clearing Stations...";
 PROGMEM const char text4_46[] = "Stations Cleared: ";
 PROGMEM const char text4_47[] = "Targeted Deauth";
+PROGMEM const char text4_48[] = " Detect Pineapple ";
+PROGMEM const char text4_49[] = " Detect MultiSSID ";
 
 //Making tables
 PROGMEM const char *text_table0[] = {text0_0,text0_1, text0_2, text0_3, text0_4, text0_5, text0_6, text0_7, text0_8};
-PROGMEM const char *text_table1[] = {text1_0,text1_1,text1_2,text1_3,text1_4,text1_5,text1_6,text1_7,text1_8,text1_9,text1_10,text1_11,text1_12,text1_13,text1_14,text1_15,text1_16,text1_17,text1_18,text1_19,text1_20,text1_21,text1_22,text1_23,text1_24,text1_25,text1_26,text1_27,text1_28,text1_29,text1_30,text1_31,text1_32,text1_33,text1_34,text1_35,text1_36,text1_37,text1_38,text1_39,text1_40,text1_41,text1_42,text1_43,text1_44,text1_45,text1_46,text1_47,text1_48,text1_49,text1_50,text1_51,text1_52,text1_53,text1_54,text1_55,text1_56,text1_57,text1_58,text1_59,text1_60,text1_61,text1_62};
+PROGMEM const char *text_table1[] = {text1_0,text1_1,text1_2,text1_3,text1_4,text1_5,text1_6,text1_7,text1_8,text1_9,text1_10,text1_11,text1_12,text1_13,text1_14,text1_15,text1_16,text1_17,text1_18,text1_19,text1_20,text1_21,text1_22,text1_23,text1_24,text1_25,text1_26,text1_27,text1_28,text1_29,text1_30,text1_31,text1_32,text1_33,text1_34,text1_35,text1_36,text1_37,text1_38,text1_39,text1_40,text1_41,text1_42,text1_43,text1_44,text1_45,text1_46,text1_47,text1_48,text1_49,text1_50,text1_51,text1_52,text1_53,text1_54,text1_55,text1_56,text1_57,text1_58,text1_59,text1_60,text1_61,text1_62,text1_63,text1_64};
 PROGMEM const char *text_table2[] = {text2_0,text2_1,text2_2,text2_3,text2_4,text2_5,text2_6,text2_7,text2_8,text2_9,text2_10,text2_11,text2_12,text2_13,text2_14};
 PROGMEM const char *text_table3[] = {text3_0,text3_1,text3_2,text3_3,text3_4,text3_5};
-PROGMEM const char *text_table4[] = {text4_0,text4_1,text4_2,text4_3,text4_4,text4_5,text4_6,text4_7,text1_54,text4_9,text4_10,text4_11,text4_12,text4_13,text4_14,text4_15,text4_16,text4_17,text4_18,text4_19,text4_20,text4_21,text4_22,text4_23,text4_24,text4_25,text4_26,text4_27,text4_28,text4_29,text4_30,text4_31,text4_32,text4_33,text4_34,text4_35,text4_36,text4_37,text4_38,text4_39,text4_40,text4_41,text4_42,text4_43,text4_44,text4_45,text4_46,text4_47};
+PROGMEM const char *text_table4[] = {text4_0,text4_1,text4_2,text4_3,text4_4,text4_5,text4_6,text4_7,text1_54,text4_9,text4_10,text4_11,text4_12,text4_13,text4_14,text4_15,text4_16,text4_17,text4_18,text4_19,text4_20,text4_21,text4_22,text4_23,text4_24,text4_25,text4_26,text4_27,text4_28,text4_29,text4_30,text4_31,text4_32,text4_33,text4_34,text4_35,text4_36,text4_37,text4_38,text4_39,text4_40,text4_41,text4_42,text4_43,text4_44,text4_45,text4_46,text4_47,text4_48,text4_49};
 
 #endif

esp32_marauder/utils.h

@@ -5,6 +5,10 @@
 #include <Arduino.h>
 #include <vector>
 
+#include "configs.h"
+
+#include "esp_heap_caps.h"
+
 struct mac_addr {
    unsigned char bytes[6];
 };
@@ -13,6 +17,7 @@ struct Station {
   uint8_t mac[6];
   bool selected;
   uint16_t packets;
+  uint16_t ap;
 };
 
 const char apple_ouis[][9] PROGMEM = {
@@ -144,6 +149,35 @@ const char xiaomi_ouis[][9] PROGMEM = {
   "90:4E:91", "C4:0B:CB", "D0:DB:32"
 };
 
+uint8_t getDRAMUsagePercent() {
+  //size_t total = heap_caps_get_total_size(MALLOC_CAP_8BIT);
+  //size_t free = heap_caps_get_free_size(MALLOC_CAP_8BIT);
+  size_t free = ESP.getFreeHeap();
+  size_t total = ESP.getHeapSize();
+  
+  if (total == 0) return 0; // Avoid division by zero
+
+  size_t used = total - free;
+  uint8_t percent = (used * 100) / total;
+  return percent;
+}
+
+#ifdef HAS_PSRAM
+  uint8_t getPSRAMUsagePercent() {
+    //size_t total = heap_caps_get_total_size(MALLOC_CAP_SPIRAM);
+    //size_t free  = heap_caps_get_free_size(MALLOC_CAP_SPIRAM);
+
+    size_t total = ESP.getPsramSize();
+    size_t free = ESP.getFreePsram();
+
+    if (total == 0) return 0; // Avoid division by zero or PSRAM not available
+
+    size_t used = total - free;
+    uint8_t percent = (used * 100) / total;
+    return percent;
+  }
+#endif
+
 String byteArrayToHexString(const std::vector<uint8_t>& byteArray) {
   String result;
 

pictures/xbm/pineapple_22.xbm

@@ -0,0 +1,9 @@
+#define be52a82b6ef24281d57d9491aef1484cv5n1Pq988C5WdKha_width 22
+#define be52a82b6ef24281d57d9491aef1484cv5n1Pq988C5WdKha_height 22
+static char be52a82b6ef24281d57d9491aef1484cv5n1Pq988C5WdKha_bits[] = {
+  0xFF, 0xFF, 0x3F, 0xFF, 0xF7, 0x3F, 0x7F, 0x96, 0x3F, 0xFF, 0xED, 0x3F, 
+  0x3F, 0x25, 0x3F, 0xDF, 0xD2, 0x3E, 0xFF, 0xED, 0x3F, 0x7F, 0x8E, 0x3F, 
+  0x3B, 0x77, 0x37, 0xBD, 0x6A, 0x2F, 0xD6, 0xBD, 0x1A, 0xDA, 0xDA, 0x16, 
+  0x5A, 0x6F, 0x16, 0x9A, 0xF7, 0x16, 0xD6, 0x5A, 0x1A, 0xDD, 0xBD, 0x2E, 
+  0xBB, 0x5A, 0x37, 0x3F, 0x6F, 0x3F, 0x7F, 0xB7, 0x3F, 0xFF, 0xCC, 0x3F, 
+  0xFF, 0xF3, 0x3F, 0xFF, 0xFF, 0x3F, };