Merge pull request #826 from justcallmekoko/develop

Develop

.github/workflows/build_parallel.yml

@@ -17,19 +17,23 @@ jobs:
       fail-fast: false
       matrix:
         board:
-          - { name: "Flipper Zero WiFi Dev Board",  flag: "MARAUDER_FLIPPER",         fbqn: "esp32:esp32:esp32s2:PartitionScheme=min_spiffs,FlashSize=4M,PSRAM=enabled",  file_name: "flipper",                 tft: false, tft_file: "",                                   build_dir: "esp32s2", addr: "0x1000" }
-          - { name: "Flipper Zero Multi Board",     flag: "MARAUDER_FLIPPER",         fbqn: "esp32:esp32:esp32s3:PartitionScheme=min_spiffs,FlashSize=8M,PSRAM=enabled",  file_name: "multiboardS3",            tft: false, tft_file: "",                                   build_dir: "esp32s3", addr: "0x0" }
-          - { name: "OG Marauder",                  flag: "MARAUDER_V4",              fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                 file_name: "og",                      tft: true,  tft_file: "User_Setup_og_marauder.h",           build_dir: "d32",     addr: "0x1000" }
-          - { name: "Marauder v6",                  flag: "MARAUDER_V6",              fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                 file_name: "v6",                      tft: true,  tft_file: "User_Setup_og_marauder.h",           build_dir: "d32",     addr: "0x1000" }
-          - { name: "Marauder v6.1",                flag: "MARAUDER_V6_1",            fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                 file_name: "v6_1",                    tft: true,  tft_file: "User_Setup_og_marauder.h",           build_dir: "d32",     addr: "0x1000" }
-          - { name: "Marauder Kit",                 flag: "MARAUDER_KIT",             fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                 file_name: "kit",                     tft: true,  tft_file: "User_Setup_og_marauder.h",           build_dir: "d32",     addr: "0x1000" }
-          - { name: "Marauder Mini",                flag: "MARAUDER_MINI",            fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                 file_name: "mini",                    tft: true,  tft_file: "User_Setup_marauder_mini.h",         build_dir: "d32",     addr: "0x1000" }
-          - { name: "ESP32 LDDB",                   flag: "ESP32_LDDB",               fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                 file_name: "esp32_lddb",              tft: false, tft_file: "",                                   build_dir: "d32",     addr: "0x1000" }
-          - { name: "Marauder Dev Board Pro",       flag: "MARAUDER_DEV_BOARD_PRO",   fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                 file_name: "marauder_dev_board_pro",  tft: false, tft_file: "",                                   build_dir: "d32",     addr: "0x1000" }
-          - { name: "M5StickCPlus",                 flag: "MARAUDER_M5STICKC",        fbqn: "esp32:esp32:m5stick-c:PartitionScheme=min_spiffs",                           file_name: "m5stickc_plus",           tft: true,  tft_file: "User_Setup_marauder_m5stickc.h",     build_dir: "m5stick-c", addr: "0x1000" }
-          - { name: "M5StickCPlus 2",               flag: "MARAUDER_M5STICKCP2",      fbqn: "esp32:esp32:m5stick-c:PartitionScheme=min_spiffs",                           file_name: "m5stickc_plus2",          tft: true,  tft_file: "User_Setup_marauder_m5stickcp2.h",   build_dir: "m5stick-c", addr: "0x1000" }
-          - { name: "Rev Feather",                  flag: "MARAUDER_REV_FEATHER",     fbqn: "esp32:esp32:esp32s2:PartitionScheme=min_spiffs,FlashSize=4M,PSRAM=enabled",  file_name: "rev_feather",             tft: true,  tft_file: "User_Setup_marauder_rev_feather.h",  build_dir: "esp32s2", addr: "0x1000" }
-          - { name: "Marauder v7",                  flag: "MARAUDER_V7",              fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                 file_name: "marauder_v7",             tft: true,  tft_file: "User_Setup_dual_nrf24.h",            build_dir: "d32",     addr: "0x1000" }
+          - { name: "Flipper Zero WiFi Dev Board",   flag: "MARAUDER_FLIPPER",         fbqn: "esp32:esp32:esp32s2:PartitionScheme=min_spiffs,FlashSize=4M,PSRAM=enabled",                     file_name: "flipper",                 tft: false, tft_file: "",                                   build_dir: "esp32s2",                    addr: "0x1000" }
+          - { name: "Flipper Zero Multi Board S3",   flag: "MARAUDER_MULTIBOARD_S3",   fbqn: "esp32:esp32:esp32s3:PartitionScheme=min_spiffs,FlashSize=4M",                                   file_name: "multiboardS3",            tft: false, tft_file: "",                                   build_dir: "esp32s3",                    addr: "0x0" }
+          - { name: "OG Marauder",                   flag: "MARAUDER_V4",              fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                                    file_name: "og",                      tft: true,  tft_file: "User_Setup_og_marauder.h",           build_dir: "d32",                        addr: "0x1000" }
+          - { name: "Marauder v6",                   flag: "MARAUDER_V6",              fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                                    file_name: "v6",                      tft: true,  tft_file: "User_Setup_og_marauder.h",           build_dir: "d32",                        addr: "0x1000" }
+          - { name: "Marauder v6.1",                 flag: "MARAUDER_V6_1",            fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                                    file_name: "v6_1",                    tft: true,  tft_file: "User_Setup_og_marauder.h",           build_dir: "d32",                        addr: "0x1000" }
+          - { name: "Marauder Kit",                  flag: "MARAUDER_KIT",             fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                                    file_name: "kit",                     tft: true,  tft_file: "User_Setup_og_marauder.h",           build_dir: "d32",                        addr: "0x1000" }
+          - { name: "Marauder Mini",                 flag: "MARAUDER_MINI",            fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                                    file_name: "mini",                    tft: true,  tft_file: "User_Setup_marauder_mini.h",         build_dir: "d32",                        addr: "0x1000" }
+          - { name: "ESP32 LDDB",                    flag: "ESP32_LDDB",               fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                                    file_name: "esp32_lddb",              tft: false, tft_file: "",                                   build_dir: "d32",                        addr: "0x1000" }
+          - { name: "Marauder Dev Board Pro",        flag: "MARAUDER_DEV_BOARD_PRO",   fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                                    file_name: "marauder_dev_board_pro",  tft: false, tft_file: "",                                   build_dir: "d32",                        addr: "0x1000" }
+          - { name: "M5StickCPlus",                  flag: "MARAUDER_M5STICKC",        fbqn: "esp32:esp32:m5stick-c:PartitionScheme=min_spiffs",                                              file_name: "m5stickc_plus",           tft: true,  tft_file: "User_Setup_marauder_m5stickc.h",     build_dir: "m5stick-c",                  addr: "0x1000" }
+          - { name: "M5StickCPlus 2",                flag: "MARAUDER_M5STICKCP2",      fbqn: "esp32:esp32:m5stick-c:PartitionScheme=min_spiffs",                                              file_name: "m5stickc_plus2",          tft: true,  tft_file: "User_Setup_marauder_m5stickcp2.h",   build_dir: "m5stick-c",                  addr: "0x1000" }
+          - { name: "Rev Feather",                   flag: "MARAUDER_REV_FEATHER",     fbqn: "esp32:esp32:esp32s2:PartitionScheme=min_spiffs,FlashSize=4M,PSRAM=enabled",                     file_name: "rev_feather",             tft: true,  tft_file: "User_Setup_marauder_rev_feather.h",  build_dir: "esp32s2",                    addr: "0x1000" }
+          - { name: "Marauder v7",                   flag: "MARAUDER_V7",              fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                                    file_name: "marauder_v7",             tft: true,  tft_file: "User_Setup_dual_nrf24.h",            build_dir: "d32",                        addr: "0x1000" }
+          - { name: "Marauder CYD 2432S028",         flag: "MARAUDER_CYD_MICRO",       fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                                    file_name: "cyd_2432S028",            tft: true,  tft_file: "User_Setup_cyd_micro.h",             build_dir: "d32",                        addr: "0x1000" }
+          - { name: "Marauder CYD 2432S024 GUITION", flag: "MARAUDER_CYD_GUITION",     fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                                    file_name: "cyd_2432S024_guition",    tft: true,  tft_file: "User_Setup_cyd_guition.h",           build_dir: "d32",                        addr: "0x1000" }
+          - { name: "Marauder CYD 2432S028 2 USB",   flag: "MARAUDER_CYD_2USB",        fbqn: "esp32:esp32:d32:PartitionScheme=min_spiffs",                                                    file_name: "cyd_2432S028_2usb",       tft: true,  tft_file: "User_Setup_cyd_2usb.h",              build_dir: "d32",                        addr: "0x1000" }
+          - { name: "Marauder v7.1",                 flag: "MARAUDER_V7_1",            fbqn: "esp32:esp32:dfrobot_firebeetle2_esp32e:FlashSize=16M,PartitionScheme=min_spiffs,PSRAM=enabled", file_name: "marauder_v7_1",           tft: true,  tft_file: "User_Setup_dual_nrf24.h",            build_dir: "dfrobot_firebeetle2_esp32e", addr: "0x1000" }
           
     steps:
       - name: Checkout Code
@@ -65,6 +69,13 @@ jobs:
         run: |
           find /home/runner/.arduino15/packages/esp32/hardware/
           
+      - name: Install ESP32Ping
+        uses: actions/checkout@v2
+        with:
+          repository: marian-craciunescu/ESP32Ping
+          ref: 1.6
+          path: CustomESP32Ping
+          
       - name: Install AsyncTCP
         uses: actions/checkout@v2
         with:
@@ -92,6 +103,13 @@ jobs:
           repository: Bodmer/TFT_eSPI
           ref: V2.5.34
           path: CustomTFT_eSPI
+          
+      - name: Install XPT2046_Touchscreen
+        uses: actions/checkout@v2
+        with:
+          repository: PaulStoffregen/XPT2046_Touchscreen
+          ref: v1.4
+          path: CustomXPT2046_Touchscreen
 
       - name: Install lv_arduino
         uses: actions/checkout@v2
@@ -111,7 +129,7 @@ jobs:
         uses: actions/checkout@v2
         with:
           repository: h2zero/NimBLE-Arduino
-          ref: 1.3.5
+          ref: 1.3.8
           path: CustomNimBLE-Arduino
 
       - name: Install Adafruit_NeoPixel

.github/workflows/build_push.yml

@@ -1,886 +0,0 @@
-name: Build and Push
-
-on:
-  workflow_dispatch:
-  pull_request:
-
-jobs:
-  # This workflow contains a single job called "build"
-  build:
-    name: Build Marauder Binaries
-    
-    runs-on: ubuntu-latest
-    
-    steps:
-      - name: Checkout Code
-        uses: actions/checkout@v3
-        
-#      - name: Install ESP32 Boards and Compile TestFile
-#        uses: ArminJo/arduino-test-compile@v3.2.1
-#        with:
-#          sketch-names: TestFile.ino
-#          arduino-board-fqbn: esp32:esp32:esp32s2
-#          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.10/package_esp32_dev_index.json
-          
-      - name: Install Arduino CLI
-        run: |
-          curl -fsSL https://raw.githubusercontent.com/arduino/arduino-cli/master/install.sh | sh
-          echo "/home/runner/work/ESP32Marauder/ESP32Marauder/bin" >> $GITHUB_PATH
-          export PATH=$PATH:/home/runner/work/ESP32Marauder/ESP32Marauder/bin
-          arduino-cli version
-
-      - name: Install Arduino-ESP32 Core v2.0.11
-        run: |
-          arduino-cli core update-index
-          arduino-cli core install esp32:esp32@2.0.11
-
-      - name: Verify Installed Cores
-        run: arduino-cli core list
-
-      - name: Build TestFile with ESP32 v2.0.11
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: TestFile.ino
-          arduino-board-fqbn: esp32:esp32:esp32s2
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-
-      - name: Verify Installed Cores Again
-        run: arduino-cli core list
-          
-      - name: Show Arduino dir structure
-        run: |
-          find /home/runner/.arduino15/packages/esp32/hardware/
-        
-#      - name: Pull arduino-esp32 v2.0.4
-#        uses: actions/checkout@v2
-#        with:
-#          repository: espressif/arduino-esp32
-#          ref: 2.0.4
-#          path: 2.0.4arduino-esp32
-          
-#      - name: Pull arduino-esp32 v2.0.10
-#        uses: actions/checkout@v2
-#        with:
-#          repository: espressif/arduino-esp32
-#          ref: 2.0.10
-#          path: 2.0.10
-          
-      - name: Install AsyncTCP
-        uses: actions/checkout@v2
-        with:
-          repository: me-no-dev/AsyncTCP
-          ref: master
-          path: CustomAsyncTCP
-          
-      - name: Install MicroNMEA
-        uses: actions/checkout@v2
-        with:
-          repository: stevemarple/MicroNMEA
-          ref: v2.0.6
-          path: CustomMicroNMEA
-          
-      - name: Install ESPAsyncWebServer
-        uses: actions/checkout@v2
-        with:
-          repository: bigbrodude6119/ESPAsyncWebServer
-          ref: master
-          path: CustomESPAsyncWebServer
-          
-      - name: Install TFT_eSPI
-        uses: actions/checkout@v2
-        with:
-          repository: Bodmer/TFT_eSPI
-          ref: V2.5.34
-          path: CustomTFT_eSPI
-
-      - name: Install lv_arduino
-        uses: actions/checkout@v2
-        with:
-          repository: lvgl/lv_arduino
-          ref: 3.0.0
-          path: Customlv_arduino
-
-      - name: Install JPEGDecoder
-        uses: actions/checkout@v2
-        with:
-          repository: Bodmer/JPEGDecoder
-          ref: 1.8.0
-          path: CustomJPEGDecoder
-
-      - name: Install NimBLE-Arduino
-        uses: actions/checkout@v2
-        with:
-          repository: h2zero/NimBLE-Arduino
-          ref: 1.3.5
-          path: CustomNimBLE-Arduino
-
-      - name: Install Adafruit_NeoPixel
-        uses: actions/checkout@v2
-        with:
-          repository: adafruit/Adafruit_NeoPixel
-          ref: 1.10.7
-          path: CustomAdafruit_NeoPixel
-
-      - name: Install ArduinoJson
-        uses: actions/checkout@v2
-        with:
-          repository: bblanchon/ArduinoJson
-          ref: v6.18.2
-          path: CustomArduinoJson
-
-      #- name: Install SwitchLib
-      #  uses: actions/checkout@v2
-      #  with:
-      #    repository: justcallmekoko/SwitchLib
-      #    ref: main
-      #    path: CustomSwitchLib
-          
-      - name: Install LinkedList
-        uses: actions/checkout@v2
-        with:
-          repository: ivanseidel/LinkedList
-          ref: v1.3.3
-          path: CustomLinkedList
-          
-      - name: Install EspSoftwareSerial
-        uses: actions/checkout@v2
-        with:
-          repository: plerup/espsoftwareserial
-          ref: 8.1.0
-          path: CustomEspSoftwareSerial
-          
-      - name: Install Adafruit_BusIO
-        uses: actions/checkout@v2
-        with:
-          repository: adafruit/Adafruit_BusIO
-          ref: 1.15.0
-          path: CustomAdafruit_BusIO
-          
-      - name: Install Adafruit_MAX1704X
-        uses: actions/checkout@v2
-        with:
-          repository: adafruit/Adafruit_MAX1704X
-          ref: 1.0.2
-          path: CustomAdafruit_MAX1704X
-          
-      #- name: Search for SD lib in arduino-esp32 v2.0.4
-      #  run: |
-      #    find /home/runner/work/ESP32Marauder/ESP32Marauder/2.0.4arduino-esp32 -name "SD"
-          
-      - name: Configure TFT_eSPI
-        run: |
-          rm -f CustomTFT_eSPI/User_Setup_Select.h
-          cp User_Setup_Select.h CustomTFT_eSPI/
-          cp User_Setup_marauder_mini.h CustomTFT_eSPI/
-          cp User_Setup_og_marauder.h CustomTFT_eSPI/
-          cp User_Setup_marauder_m5stickc.h CustomTFT_eSPI/
-          cp User_Setup_marauder_m5stickcp2.h CustomTFT_eSPI/
-          cp User_Setup_marauder_rev_feather.h CustomTFT_eSPI/
-          cp User_Setup_dual_nrf24.h CustomTFT_eSPI/
-          pwd
-          ls -la
-          ls -la CustomTFT_eSPI
-          
-      #- name: Place 2.0.10 for use
-      #  run: |
-      #    mkdir -p /home/runner/.arduino15/packages/esp32/hardware/esp32/
-      #    cp -R /home/runner/work/ESP32Marauder/ESP32Marauder/2.0.3 /home/runner/.arduino15/packages/esp32/hardware/esp32/2.0.3
-      #    ls -la /home/runner/.arduino15/packages/esp32/hardware/esp32/
-      #    echo Whoever made me have to do this can fuck off
-          
-      #- name: Replace arduino-esp32 v2.0.10 that was gloriously forced on us
-      #  run: |
-      #    rm -rf /home/runner/.arduino15/packages/esp32/hardware/esp32/2.0.10
-      #    cp -R /home/runner/work/ESP32Marauder/ESP32Marauder/2.0.3 /home/runner/.arduino15/packages/esp32/hardware/esp32/2.0.3
-      #    ls -la /home/runner/.arduino15/packages/esp32/hardware/esp32/
-      #    echo Whoever made me have to do this can fuck off
-          
-      #- name: Search for SD lib in arduino-esp32
-      #  run: |
-      #    find /home/runner/ -name "SD"
-          
-      #- name: Replace SD lib
-      #  run: |
-      #    rm -rf /home/runner/.arduino15/packages/esp32/hardware/esp32/2.0.10/libraries/SD
-      #    cp -R /home/runner/work/ESP32Marauder/ESP32Marauder/2.0.4arduino-esp32/libraries/SD /home/runner/.arduino15/packages/esp32/hardware/esp32/2.0.10/libraries/SD
-      #    ls -la /home/runner/.arduino15/packages/esp32/hardware/esp32/2.0.10/libraries/SD
-          
-      - name: Modify platform.txt
-        run: |
-          for i in $(find /home/runner/.arduino15/packages/esp32/hardware/esp32/ -name "platform.txt"); do
-            sed -i 's/compiler.c.elf.libs.esp32c3=/compiler.c.elf.libs.esp32c3=-zmuldefs /' "$i"
-            sed -i 's/compiler.c.elf.libs.esp32s3=/compiler.c.elf.libs.esp32s3=-zmuldefs /' "$i"
-            sed -i 's/compiler.c.elf.libs.esp32s2=/compiler.c.elf.libs.esp32s2=-zmuldefs /' "$i"
-            sed -i 's/compiler.c.elf.libs.esp32=/compiler.c.elf.libs.esp32=-zmuldefs /' "$i"
-            cat "$i" | grep compiler.c.elf.libs.esp32c3
-            cat "$i" | grep compiler.c.elf.libs.esp32s3
-            cat "$i" | grep compiler.c.elf.libs.esp32s2
-            cat "$i" | grep compiler.c.elf.libs.esp32
-          done
-          
-      - name: Configure configs.h for Flipper Zero WiFi Dev Board
-        run: |
-          sed -i 's/^  #define MARAUDER_REV_FEATHER/  \/\/#define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_M5STICKC/  \/\/#define MARAUDER_M5STICKC/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_MINI/  \/\/#define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V4/  \/\/#define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6/  \/\/#define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6_1/  \/\/#define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V7/  \/\/#define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_KIT/  \/\/#define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  \/\/#define MARAUDER_FLIPPER/  #define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  #define ESP32_LDDB/  \/\/#define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_DEV_BOARD_PRO/  \/\/#define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-                    
-      - name: Build Marauder for Flipper Zero WiFi Dev Board
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:esp32s2:PartitionScheme=min_spiffs,FlashSize=4M,PSRAM=enabled
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename Marauder Flipper bin
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.esp32s2/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.esp32s2/esp32_marauder.flipper.bin
-          
-      - name: Build Marauder for Flipper Zero Multi Board
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:esp32s3:PartitionScheme=min_spiffs,FlashSize=8M,PSRAM=enabled
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename Marauder Multi Board bin
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.esp32s3/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.esp32s3/esp32_marauder.multiboardS3.bin
-         
-      - name: Configure TFT_eSPI and configs.h for OG Marauder
-        run: |
-          pwd
-          find /home/runner/ -name "*TFT_eSPI*"     
-          sed -i 's/^#include <User_Setup_marauder_rev_feather.h>/\/\/#include <User_Setup_marauder_rev_feather.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h          
-          sed -i 's/^#include <User_Setup_marauder_mini.h>/\/\/#include <User_Setup_marauder_mini.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_marauder_m5stickc.h>/\/\/#include <User_Setup_marauder_m5stickc.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_dual_nrf24.h>/\/\/#include <User_Setup_dual_nrf24.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^\/\/#include <User_Setup_og_marauder.h>/#include <User_Setup_og_marauder.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^  #define MARAUDER_REV_FEATHER/  \/\/#define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_MINI/  \/\/#define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  \/\/#define MARAUDER_V4/  #define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6/  \/\/#define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6_1/  \/\/#define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V7/  \/\/#define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_KIT/  \/\/#define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_FLIPPER/  \/\/#define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  #define ESP32_LDDB/  \/\/#define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_DEV_BOARD_PRO/  \/\/#define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-          
-      - name: Build Marauder for OG Marauder
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:d32:PartitionScheme=min_spiffs
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename OG Marauder bin
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.og.bin
-          
-      - name: Configure TFT_eSPI and configs.h for Marauder v6
-        run: |
-          sed -i 's/^#include <User_Setup_marauder_rev_feather.h>/\/\/#include <User_Setup_marauder_rev_feather.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_marauder_mini.h>/\/\/#include <User_Setup_marauder_mini.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_marauder_m5stickc.h>/\/\/#include <User_Setup_marauder_m5stickc.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_dual_nrf24.h>/\/\/#include <User_Setup_dual_nrf24.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^\/\/#include <User_Setup_og_marauder.h>/#include <User_Setup_og_marauder.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^  #define MARAUDER_REV_FEATHER/  \/\/#define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_MINI/  \/\/#define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V4/  \/\/#define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  \/\/#define MARAUDER_V6/  #define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6_1/  \/\/#define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V7/  \/\/#define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_KIT/  \/\/#define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_FLIPPER/  \/\/#define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  #define ESP32_LDDB/  \/\/#define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_DEV_BOARD_PRO/  \/\/#define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-          
-      #- name: Build Marauder for v6 Marauder with arduino/compile-sketches
-      #  uses: arduino/compile-sketches@v1
-      #  with:
-      #    sketch-paths: esp32_marauder/esp32_marauder.ino
-      #    cli-compile-flags: |
-      #      - --warnings="none"
-      #      - --export-binaries
-      #    fqbn: esp32:esp32:d32:PartitionScheme=min_spiffs
-          
-      #- name: Show compiled arduino/compile-sketches v6 bin
-      #  run: |
-      #    find ~ -name "esp32_marauder.ino.bin"
-          
-      #- name: Rename v6_2 Marauder bin
-      #  run: |
-      #    mv ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.v6_2.bin
-          
-      - name: Build Marauder for v6 Marauder
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:d32:PartitionScheme=min_spiffs
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename v6 Marauder bin
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.v6.bin
-          
-      - name: Configure TFT_eSPI and configs.h for Marauder v6.1
-        run: |
-          sed -i 's/^  #define MARAUDER_REV_FEATHER/  \/\/#define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_MINI/  \/\/#define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V4/  \/\/#define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6/  \/\/#define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  \/\/#define MARAUDER_V6_1/  #define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V7/  \/\/#define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_KIT/  \/\/#define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_FLIPPER/  \/\/#define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  #define ESP32_LDDB/  \/\/#define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_DEV_BOARD_PRO/  \/\/#define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-          
-      - name: Build Marauder for v6.1 Marauder
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:d32:PartitionScheme=min_spiffs
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename v6 Marauder bin
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.v6_1.bin
-         
-      - name: Configure TFT_eSPI and configs.h for Marauder Kit
-        run: |
-          sed -i 's/^#include <User_Setup_marauder_mini.h>/\/\/#include <User_Setup_marauder_mini.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_marauder_m5stickc.h>/\/\/#include <User_Setup_marauder_m5stickc.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_dual_nrf24.h>/\/\/#include <User_Setup_dual_nrf24.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^\/\/#include <User_Setup_og_marauder.h>/#include <User_Setup_og_marauder.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^  #define MARAUDER_REV_FEATHER/  \/\/#define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_MINI/  \/\/#define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V4/  \/\/#define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6/  \/\/#define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6_1/  \/\/#define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V7/  \/\/#define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  \/\/#define MARAUDER_KIT/  #define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_FLIPPER/  \/\/#define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  #define ESP32_LDDB/  \/\/#define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_DEV_BOARD_PRO/  \/\/#define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-          
-      - name: Build Marauder for Marauder Kit
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:d32:PartitionScheme=min_spiffs
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename Marauder Kit bin
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.kit.bin
-          
-      - name: Configure TFT_eSPI and configs.h for Marauder Mini
-        run: |
-          sed -i 's/^\/\/#include <User_Setup_marauder_mini.h>/#include <User_Setup_marauder_mini.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_og_marauder.h>/\/\/#include <User_Setup_og_marauder.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_marauder_m5stickc.h>/\/\/#include <User_Setup_marauder_m5stickc.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_dual_nrf24.h>/\/\/#include <User_Setup_dual_nrf24.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^  #define MARAUDER_REV_FEATHER/  \/\/#define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  \/\/#define MARAUDER_MINI/  #define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V4/  \/\/#define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6/  \/\/#define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6_1/  \/\/#define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V7/  \/\/#define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_KIT/  \/\/#define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_FLIPPER/  \/\/#define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  #define ESP32_LDDB/  \/\/#define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_DEV_BOARD_PRO/  \/\/#define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-          
-      - name: Build Marauder for Marauder Mini
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:d32:PartitionScheme=min_spiffs
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename Marauder Mini bin
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.mini.bin
-          
-      - name: Configure TFT_eSPI and configs.h for ESP32 LDDB
-        run: |
-          sed -i 's/^  #define MARAUDER_REV_FEATHER/  \/\/#define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_MINI/  \/\/#define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V4/  \/\/#define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6/  \/\/#define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6_1/  \/\/#define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V7/  \/\/#define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_KIT/  \/\/#define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_FLIPPER/  \/\/#define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  \/\/#define ESP32_LDDB/  #define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_DEV_BOARD_PRO/  \/\/#define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-          
-      - name: Build Marauder for ESP32 LDDB
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:d32:PartitionScheme=min_spiffs
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename Marauder ESP32 LDDB bin
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.esp32_lddb.bin
-
-      - name: Configure TFT_eSPI and configs.h for Marauder Dev Board Pro
-        run: |
-          sed -i 's/^  #define MARAUDER_REV_FEATHER/  \/\/#define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_MINI/  \/\/#define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V4/  \/\/#define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6/  \/\/#define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6_1/  \/\/#define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V7/  \/\/#define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_KIT/  \/\/#define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_FLIPPER/  \/\/#define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  #define ESP32_LDDB/  \/\/#define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  \/\/#define MARAUDER_DEV_BOARD_PRO/  #define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-          
-      - name: Build Marauder for Marauder Dev Board Pro
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:d32:PartitionScheme=min_spiffs
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename Marauder for Marauder Dev Board Pro
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.marauder_dev_board_pro.bin
-          
-      - name: Configure TFT_eSPI and configs.h for Marauder M5StickC
-        run: |
-          pwd
-          find /home/runner/ -name "*TFT_eSPI*"          
-          sed -i 's/^#include <User_Setup_marauder_mini.h>/\/\/#include <User_Setup_marauder_mini.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^\/\/#include <User_Setup_marauder_m5stickc.h>/#include <User_Setup_marauder_m5stickc.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^  #define MARAUDER_REV_FEATHER/  \/\/#define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_MINI/  \/\/#define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V4/  \/\/#define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6/  \/\/#define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6_1/  \/\/#define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V7/  \/\/#define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_KIT/  \/\/#define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_FLIPPER/  \/\/#define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  #define ESP32_LDDB/  \/\/#define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_DEV_BOARD_PRO/  \/\/#define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-          sed -i 's/^  \/\/#define MARAUDER_M5STICKC /  #define MARAUDER_M5STICKC /' esp32_marauder/configs.h
-          
-      - name: Build Marauder for Marauder M5StickC
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:m5stick-c:PartitionScheme=min_spiffs
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename Marauder M5StickC bin
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.m5stick-c/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.m5stick-c/esp32_marauder.m5stickc_plus.bin
-
-      - name: Configure TFT_eSPI and configs.h for Marauder M5StickCP2
-        run: |
-          pwd
-          find /home/runner/ -name "*TFT_eSPI*"          
-          sed -i 's/^#include <User_Setup_marauder_mini.h>/\/\/#include <User_Setup_marauder_mini.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_marauder_m5stickc.h>/\/\/#include <User_Setup_marauder_m5stickc.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^\/\/#include <User_Setup_marauder_m5stickcp2.h>/#include <User_Setup_marauder_m5stickcp2.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^  #define MARAUDER_REV_FEATHER/  \/\/#define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_MINI/  \/\/#define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V4/  \/\/#define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6/  \/\/#define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6_1/  \/\/#define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V7/  \/\/#define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_KIT/  \/\/#define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_FLIPPER/  \/\/#define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  #define ESP32_LDDB/  \/\/#define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_DEV_BOARD_PRO/  \/\/#define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_M5STICKC /  \/\/#define MARAUDER_M5STICKC /' esp32_marauder/configs.h
-          sed -i 's/^  \/\/#define MARAUDER_M5STICKCP2/  #define MARAUDER_M5STICKCP2/' esp32_marauder/configs.h
-          
-      - name: Build Marauder for Marauder M5StickCP2
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:m5stick-c:PartitionScheme=min_spiffs
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename Marauder M5StickCP2 bin
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.m5stick-c/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.m5stick-c/esp32_marauder.m5stickc_plus2.bin
-
-      - name: Configure TFT_eSPI and configs.h for Marauder Rev Feather
-        run: |
-          pwd
-          find /home/runner/ -name "*TFT_eSPI*"          
-          sed -i 's/^\/\/#include <User_Setup_marauder_rev_feather.h>/#include <User_Setup_marauder_rev_feather.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_marauder_mini.h>/\/\/#include <User_Setup_marauder_mini.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_marauder_m5stickc.h>/\/\/#include <User_Setup_marauder_m5stickc.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_marauder_m5stickcp2.h>/\/\/#include <User_Setup_marauder_m5stickcp2.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^  \/\/#define MARAUDER_REV_FEATHER/  #define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_MINI/  \/\/#define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V4/  \/\/#define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6/  \/\/#define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6_1/  \/\/#define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V7/  \/\/#define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_KIT/  \/\/#define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_FLIPPER/  \/\/#define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  #define ESP32_LDDB/  \/\/#define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_DEV_BOARD_PRO/  \/\/#define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_M5STICKC /  \/\/#define MARAUDER_M5STICKC /' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_M5STICKCP2/  \/\/#define MARAUDER_M5STICKCP2/' esp32_marauder/configs.h
-          
-      - name: Build Marauder for Marauder Rev Feather
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:esp32s2:PartitionScheme=min_spiffs,FlashSize=4M,PSRAM=enabled
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename Marauder Marauder Rev Feather
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.esp32s2/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.esp32s2/esp32_marauder.rev_feather.bin
-          
-      - name: Configure TFT_eSPI and configs.h for Marauder v7
-        run: |
-          pwd
-          find /home/runner/ -name "*TFT_eSPI*"          
-          sed -i 's/^#include <User_Setup_marauder_rev_feather.h>/\/\/#include <User_Setup_marauder_rev_feather.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_marauder_mini.h>/\/\/#include <User_Setup_marauder_mini.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^#include <User_Setup_marauder_m5stickc.h>/\/\/#include <User_Setup_marauder_m5stickc.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^\/\/#include <User_Setup_dual_nrf24.h>/#include <User_Setup_dual_nrf24.h>/' /home/runner/Arduino/libraries/CustomTFT_eSPI/User_Setup_Select.h
-          sed -i 's/^  #define MARAUDER_REV_FEATHER/  \/\/#define MARAUDER_REV_FEATHER/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_MINI/  \/\/#define MARAUDER_MINI/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V4/  \/\/#define MARAUDER_V4/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6/  \/\/#define MARAUDER_V6/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_V6_1/  \/\/#define MARAUDER_V6_1/' esp32_marauder/configs.h
-          sed -i 's/^  \/\/#define MARAUDER_V7/  #define MARAUDER_V7/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_KIT/  \/\/#define MARAUDER_KIT/' esp32_marauder/configs.h
-          sed -i 's/^  #define GENERIC_ESP32/  \/\/#define GENERIC_ESP32/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_FLIPPER/  \/\/#define MARAUDER_FLIPPER/' esp32_marauder/configs.h
-          sed -i 's/^  #define ESP32_LDDB/  \/\/#define ESP32_LDDB/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_DEV_BOARD_PRO/  \/\/#define MARAUDER_DEV_BOARD_PRO/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_M5STICKC/  \/\/#define MARAUDER_M5STICKC/' esp32_marauder/configs.h
-          sed -i 's/^  #define MARAUDER_M5STICKCP2/  \/\/#define MARAUDER_M5STICKCP2/' esp32_marauder/configs.h
-          
-      - name: Build Marauder for Marauder v7
-        uses: ArminJo/arduino-test-compile@v3.2.1
-        with:
-          sketch-names: esp32_marauder.ino
-          arduino-board-fqbn: esp32:esp32:d32:PartitionScheme=min_spiffs
-          extra-arduino-cli-args: "--warnings none"
-          arduino-platform: esp32:esp32@2.0.11
-          platform-url: https://github.com/espressif/arduino-esp32/releases/download/2.0.11/package_esp32_dev_index.json
-          
-      - name: Rename Marauder Marauder v7
-        run: |
-          mv ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.ino.bin ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.marauder_v7.bin
-
-      - name: Display finished bins
-        run: |
-          find ./esp32_marauder/build -name "*.bin"
-          
-      - name: 'Upload Flipper Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.flipper.bin
-          path: ./esp32_marauder/build/esp32.esp32.esp32s2/esp32_marauder.flipper.bin
-          retention-days: 5
-          
-      - name: 'Upload MultiboardS3 Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.multiboardS3.bin
-          path: ./esp32_marauder/build/esp32.esp32.esp32s3/esp32_marauder.multiboardS3.bin
-          retention-days: 5
-          
-      - name: 'Upload OG Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.og.bin
-          path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.og.bin
-          retention-days: 5
-          
-      - name: 'Upload v6 Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.v6.bin
-          path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.v6.bin
-          retention-days: 5
-          
-      - name: 'Upload v6_1 Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.v6_1.bin
-          path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.v6_1.bin
-          retention-days: 5
-          
-      - name: 'Upload Kit Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.kit.bin
-          path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.kit.bin
-          retention-days: 5
-          
-      - name: 'Upload Mini Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.mini.bin
-          path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.mini.bin
-          retention-days: 5
-          
-      - name: 'Upload ESP32 LDDB Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.esp32_lddb.bin
-          path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.esp32_lddb.bin
-          retention-days: 5
-          
-      - name: 'Upload Marauder Dev Board Pro Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.marauder_dev_board_pro.bin
-          path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.marauder_dev_board_pro.bin
-          retention-days: 5
-          
-      - name: 'Upload Marauder M5StickC Plus Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.m5stickc_plus.bin
-          path: ./esp32_marauder/build/esp32.esp32.m5stick-c/esp32_marauder.m5stickc_plus.bin
-          retention-days: 5
-
-      - name: 'Upload Marauder M5StickC Plus 2 Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.m5stickc_plus2.bin
-          path: ./esp32_marauder/build/esp32.esp32.m5stick-c/esp32_marauder.m5stickc_plus2.bin
-          retention-days: 5
-          
-      - name: 'Upload Rev Feather Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.rev_feather.bin
-          path: ./esp32_marauder/build/esp32.esp32.esp32s2/esp32_marauder.rev_feather.bin
-          retention-days: 5
-          
-      - name: 'Upload Marauder v7 Artifact'
-        uses: actions/upload-artifact@v4
-        with:
-          name: esp32_marauder.marauder_v7.bin
-          path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.marauder_v7.bin
-          retention-days: 5
-          
-      - name: Create Release
-        id: create_release
-        uses: actions/create-release@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          tag_name: ${{ github.ref }}
-          release_name: Release ${{ github.ref }}
-          draft: true
-          prerelease: false
-        if: github.event_name != 'pull_request'
-          
-      - name: Upload Flipper Asset
-        id: upload-flipper-release-asset 
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.esp32s2/esp32_marauder.flipper.bin
-          asset_name: esp32_marauder.flipper.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-          
-      - name: Upload MultiboardS3 Asset
-        id: upload-multiboardS3-release-asset 
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.esp32s3/esp32_marauder.multiboardS3.bin
-          asset_name: esp32_marauder.multiboardS3.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-          
-      - name: Upload OG Asset
-        id: upload-og-release-asset 
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.og.bin
-          asset_name: esp32_marauder.og.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-          
-      - name: Upload v6 Asset
-        id: upload-v6-release-asset 
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.v6.bin
-          asset_name: esp32_marauder.v6.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-        
-      - name: Upload v6_1 Asset
-        id: upload-v6-1-release-asset 
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.v6_1.bin
-          asset_name: esp32_marauder.v6_1.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-          
-      - name: Upload Kit Asset
-        id: upload-kit-release-asset 
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.kit.bin
-          asset_name: esp32_marauder.kit.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-          
-      - name: Upload Mini Asset
-        id: upload-mini-release-asset 
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.mini.bin
-          asset_name: esp32_marauder.mini.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-          
-      - name: Upload ESP32 LDDB Asset
-        id: upload-esp32-lddb-release-asset 
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.esp32_lddb.bin
-          asset_name: esp32_marauder.esp32_lddb.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-          
-      - name: Upload Marauder Dev Board Pro Asset
-        id: upload-marauder-dev-board-pro-release-asset
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.marauder_dev_board_pro.bin
-          asset_name: esp32_marauder.marauder_dev_board_pro.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-        
-      - name: Upload Marauder M5StickC Plus Asset
-        id: upload-m5stickc-plus-release-asset 
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.m5stick-c/esp32_marauder.m5stickc_plus.bin
-          asset_name: esp32_marauder.m5stickc_plus.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-
-      - name: Upload Marauder M5StickC Plus 2 Asset
-        id: upload-m5stickc-plus2-release-asset 
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.m5stick-c/esp32_marauder.m5stickc_plus2.bin
-          asset_name: esp32_marauder.m5stickc_plus2.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-
-      - name: Upload Rev Feather Asset
-        id: upload-rev-feather-release-asset 
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.esp32s2/esp32_marauder.rev_feather.bin
-          asset_name: esp32_marauder.rev_feather.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'
-        
-      - name: Upload Marauder v7 Asset
-        id: upload-marauder-v7-release-asset
-        uses: actions/upload-release-asset@v1
-        env:
-          GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-        with:
-          upload_url: ${{ steps.create_release.outputs.upload_url }}
-          asset_path: ./esp32_marauder/build/esp32.esp32.d32/esp32_marauder.marauder_v7.bin
-          asset_name: esp32_marauder.marauder_v7.bin
-          asset_content_type: application/bin
-        if: github.event_name != 'pull_request'

README.md

@@ -4,7 +4,7 @@
 <!---Shields/Badges https://shields.io/--->
 
 # ESP32 Marauder
-<p align="center"><img alt="Marauder logo" src="https://github.com/justcallmekoko/ESP32Marauder/blob/master/pictures/marauder3L.jpg?raw=true" width="300"></p>
+<p align="center"><img alt="Marauder logo" src="https://github.com/justcallmekoko/ESP32Marauder/blob/master/pictures/marauder_skull_patch_04_full_final.png?raw=true" width="300"></p>
 <p align="center">
   <b>A suite of WiFi/Bluetooth offensive and defensive tools for the ESP32</b>
   <br><br>

User_Setup_Select.h

@@ -30,6 +30,10 @@
 //#include <User_Setup_pocket_sdr.h>
 //#include <User_Setup_dual_nrf24.h>
 //#include <User_Setup_pocket_sdr_2.h>
+//#include <User_Setup_pocket_sdr_3.h>
+//#include <User_Setup_cyd_micro.h>
+//#include <User_Setup_cyd_guition.h>
+//#include <User_Setup_cyd_2usb.h>
 
 //#include <User_Setups/Setup1_ILI9341.h>  // Setup file configured for my ILI9341
 //#include <User_Setups/Setup2_ST7735.h>   // Setup file configured for my ST7735

User_Setup_cyd_2usb.h

@@ -0,0 +1,316 @@
+//                            USER DEFINED SETTINGS
+//   Set driver type, fonts to be loaded, pins used and SPI control method etc
+//
+//   See the User_Setup_Select.h file if you wish to be able to define multiple
+//   setups and then easily select which setup file is used by the compiler.
+//
+//   If this file is edited correctly then all the library example sketches should
+//   run without the need to make any more changes for a particular hardware setup!
+//   Note that some sketches are designed for a particular TFT pixel width/height
+
+
+// ##################################################################################
+//
+// Section 1. Call up the right driver file and any options for it
+//
+// ##################################################################################
+
+// Display type -  only define if RPi display
+//#define RPI_DRIVER
+
+// Only define one driver, the other ones must be commented out
+//#define ILI9341_DRIVER // OG Marauder
+//#define ST7735_DRIVER    // Marauder Mini  // Define additional parameters below for this display
+//#define ILI9163_DRIVER     // Define additional parameters below for this display
+//#define S6D02A1_DRIVER
+//#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
+//#define HX8357D_DRIVER
+//#define ILI9481_DRIVER
+//#define ILI9486_DRIVER
+//#define ILI9488_DRIVER     // WARNING: Do not connect ILI9488 display SDO to MISO if other devices share the SPI bus (TFT SDO does NOT tristate when CS is high)
+#define ST7789_DRIVER      // Full configuration option, define additional parameters below for this display
+//#define ST7789_2_DRIVER    // Minimal configuration option, define additional parameters below for this display
+//#define R61581_DRIVER
+//#define RM68140_DRIVER
+//#define ST7796_DRIVER
+
+// Some displays support SPI reads via the MISO pin, other displays have a single
+// bi-directional SDA pin and the library will try to read this via the MOSI line.
+// To use the SDA line for reading data from the TFT uncomment the following line:
+
+// #define TFT_SDA_READ      // This option is for ESP32 ONLY, tested with ST7789 display only
+
+// For ST7789 and ILI9341 ONLY, define the colour order IF the blue and red are swapped on your display
+// Try ONE option at a time to find the correct colour order for your display
+
+//  #define TFT_RGB_ORDER TFT_RGB  // Colour order Red-Green-Blue
+  #define TFT_RGB_ORDER TFT_BGR  // Colour order Blue-Green-Red
+
+// For M5Stack ESP32 module with integrated ILI9341 display ONLY, remove // in line below
+
+// #define M5STACK
+
+// For ST7789, ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation
+// #define TFT_WIDTH  80
+// #define TFT_WIDTH  128 // Marauder Mini
+ #define TFT_WIDTH  240 // ST7789 240 x 240 and 240 x 320
+// #define TFT_HEIGHT 160
+// #define TFT_HEIGHT 128 // Marauder Mini
+// #define TFT_HEIGHT 240 // ST7789 240 x 240
+ #define TFT_HEIGHT 320 // ST7789 240 x 320
+
+// For ST7735 ONLY, define the type of display, originally this was based on the
+// colour of the tab on the screen protector film but this is not always true, so try
+// out the different options below if the screen does not display graphics correctly,
+// e.g. colours wrong, mirror images, or tray pixels at the edges.
+// Comment out ALL BUT ONE of these options for a ST7735 display driver, save this
+// this User_Setup file, then rebuild and upload the sketch to the board again:
+
+// #define ST7735_INITB
+// #define ST7735_GREENTAB
+// #define ST7735_GREENTAB2
+// #define ST7735_GREENTAB3
+// #define ST7735_GREENTAB128    // For 128 x 128 display
+// #define ST7735_GREENTAB160x80 // For 160 x 80 display (BGR, inverted, 26 offset)
+// #define ST7735_REDTAB
+// #define ST7735_BLACKTAB
+// #define ST7735_REDTAB160x80   // For 160 x 80 display with 24 pixel offset
+
+// If colours are inverted (white shows as black) then uncomment one of the next
+// 2 lines try both options, one of the options should correct the inversion.
+
+// #define TFT_INVERSION_ON
+ #define TFT_INVERSION_OFF
+
+// If a backlight control signal is available then define the TFT_BL pin in Section 2
+// below. The backlight will be turned ON when tft.begin() is called, but the library
+// needs to know if the LEDs are ON with the pin HIGH or LOW. If the LEDs are to be
+// driven with a PWM signal or turned OFF/ON then this must be handled by the user
+// sketch. e.g. with digitalWrite(TFT_BL, LOW);
+
+// #define TFT_BACKLIGHT_ON LOW  // HIGH or LOW are options
+
+// ##################################################################################
+//
+// Section 2. Define the pins that are used to interface with the display here
+//
+// ##################################################################################
+
+// We must use hardware SPI, a minimum of 3 GPIO pins is needed.
+// Typical setup for ESP8266 NodeMCU ESP-12 is :
+//
+// Display SDO/MISO  to NodeMCU pin D6 (or leave disconnected if not reading TFT)
+// Display LED       to NodeMCU pin VIN (or 5V, see below)
+// Display SCK       to NodeMCU pin D5
+// Display SDI/MOSI  to NodeMCU pin D7
+// Display DC (RS/AO)to NodeMCU pin D3
+// Display RESET     to NodeMCU pin D4 (or RST, see below)
+// Display CS        to NodeMCU pin D8 (or GND, see below)
+// Display GND       to NodeMCU pin GND (0V)
+// Display VCC       to NodeMCU 5V or 3.3V
+//
+// The TFT RESET pin can be connected to the NodeMCU RST pin or 3.3V to free up a control pin
+//
+// The DC (Data Command) pin may be labeled AO or RS (Register Select)
+//
+// With some displays such as the ILI9341 the TFT CS pin can be connected to GND if no more
+// SPI devices (e.g. an SD Card) are connected, in this case comment out the #define TFT_CS
+// line below so it is NOT defined. Other displays such at the ST7735 require the TFT CS pin
+// to be toggled during setup, so in these cases the TFT_CS line must be defined and connected.
+//
+// The NodeMCU D0 pin can be used for RST
+//
+//
+// Note: only some versions of the NodeMCU provide the USB 5V on the VIN pin
+// If 5V is not available at a pin you can use 3.3V but backlight brightness
+// will be lower.
+
+
+// ###### EDIT THE PIN NUMBERS IN THE LINES FOLLOWING TO SUIT YOUR ESP8266 SETUP ######
+
+// For NodeMCU - use pin numbers in the form PIN_Dx where Dx is the NodeMCU pin designation
+//#define TFT_CS   PIN_D8  // Chip select control pin D8
+//#define TFT_DC   PIN_D3  // Data Command control pin
+//#define TFT_RST  PIN_D4  // Reset pin (could connect to NodeMCU RST, see next line)
+//#define TFT_RST  -1    // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
+
+//#define TFT_BL PIN_D1  // LED back-light (only for ST7789 with backlight control pin)
+
+//#define TOUCH_CS PIN_D2     // Chip select pin (T_CS) of touch screen
+
+//#define TFT_WR PIN_D2       // Write strobe for modified Raspberry Pi TFT only
+
+
+// ######  FOR ESP8266 OVERLAP MODE EDIT THE PIN NUMBERS IN THE FOLLOWING LINES  ######
+
+// Overlap mode shares the ESP8266 FLASH SPI bus with the TFT so has a performance impact
+// but saves pins for other functions. It is best not to connect MISO as some displays
+// do not tristate that line wjen chip select is high!
+// On NodeMCU 1.0 SD0=MISO, SD1=MOSI, CLK=SCLK to connect to TFT in overlap mode
+// On NodeMCU V3  S0 =MISO, S1 =MOSI, S2 =SCLK
+// In ESP8266 overlap mode the following must be defined
+
+//#define TFT_SPI_OVERLAP
+
+// In ESP8266 overlap mode the TFT chip select MUST connect to pin D3
+//#define TFT_CS   PIN_D3
+//#define TFT_DC   PIN_D5  // Data Command control pin
+//#define TFT_RST  PIN_D4  // Reset pin (could connect to NodeMCU RST, see next line)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
+
+
+// ###### EDIT THE PIN NUMBERS IN THE LINES FOLLOWING TO SUIT YOUR ESP32 SETUP   ######
+
+// For ESP32 Dev board (only tested with ILI9341 display)
+// The hardware SPI can be mapped to any pins
+
+// Marauder Mini
+/*
+#define TFT_CS   17  // Chip select control pin D8
+#define TFT_DC   16  // Data Command control pin
+#define TFT_RST  5  // Reset pin (could connect to NodeMCU RST, see next line)
+//#define TFT_MISO 19
+//#define TFT_MOSI 23
+//#define TFT_SCLK 18
+//#define TFT_BL   32
+*/
+
+// ESP32 Marauder 
+#define TFT_MISO 12
+#define TFT_MOSI 13
+#define TFT_SCLK 14
+#define TFT_CS   15  // Chip select control pin
+#define TFT_DC   2  // Data Command control pin
+#define TFT_RST   -1  // Reset pin (could connect to RST pin)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if display RESET is connected to ESP32 board RST
+
+#define TFT_BL   21  // LED back-light (only for ST7789 with backlight control pin)
+
+#define TOUCH_CS   33     // Chip select pin (T_CS) of touch screen
+
+/////////////////////////////
+
+// ESP32 Centauri
+/*
+#define TFT_MISO 19
+#define TFT_MOSI 23
+#define TFT_SCLK 18
+#define TFT_CS   27  // Chip select control pin
+#define TFT_DC   26  // Data Command control pin
+#define TFT_RST   5  // Reset pin (could connect to RST pin)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if display RESET is connected to ESP32 board RST
+
+#define TFT_BL   32  // LED back-light (only for ST7789 with backlight control pin)
+
+#define TOUCH_CS 21     // Chip select pin (T_CS) of touch screen
+*/
+/////////////////////////////
+
+//#define TFT_WR 22    // Write strobe for modified Raspberry Pi TFT only
+
+// For the M5Stack module use these #define lines
+//#define TFT_MISO 19
+//#define TFT_MOSI 23
+//#define TFT_SCLK 18
+//#define TFT_CS   14  // Chip select control pin
+//#define TFT_DC   27  // Data Command control pin
+//#define TFT_RST  33  // Reset pin (could connect to Arduino RESET pin)
+//#define TFT_BL   32  // LED back-light (required for M5Stack)
+
+// ######       EDIT THE PINs BELOW TO SUIT YOUR ESP32 PARALLEL TFT SETUP        ######
+
+// The library supports 8 bit parallel TFTs with the ESP32, the pin
+// selection below is compatible with ESP32 boards in UNO format.
+// Wemos D32 boards need to be modified, see diagram in Tools folder.
+// Only ILI9481 and ILI9341 based displays have been tested!
+
+// Parallel bus is only supported on ESP32
+// Uncomment line below to use ESP32 Parallel interface instead of SPI
+
+//#define ESP32_PARALLEL
+
+// The ESP32 and TFT the pins used for testing are:
+//#define TFT_CS   33  // Chip select control pin (library pulls permanently low
+//#define TFT_DC   15  // Data Command control pin - must use a pin in the range 0-31
+//#define TFT_RST  32  // Reset pin, toggles on startup
+
+//#define TFT_WR    4  // Write strobe control pin - must use a pin in the range 0-31
+//#define TFT_RD    2  // Read strobe control pin
+
+//#define TFT_D0   12  // Must use pins in the range 0-31 for the data bus
+//#define TFT_D1   13  // so a single register write sets/clears all bits.
+//#define TFT_D2   26  // Pins can be randomly assigned, this does not affect
+//#define TFT_D3   25  // TFT screen update performance.
+//#define TFT_D4   17
+//#define TFT_D5   16
+//#define TFT_D6   27
+//#define TFT_D7   14
+
+
+// ##################################################################################
+//
+// Section 3. Define the fonts that are to be used here
+//
+// ##################################################################################
+
+// Comment out the #defines below with // to stop that font being loaded
+// The ESP8366 and ESP32 have plenty of memory so commenting out fonts is not
+// normally necessary. If all fonts are loaded the extra FLASH space required is
+// about 17Kbytes. To save FLASH space only enable the fonts you need!
+
+#define LOAD_GLCD   // Font 1. Original Adafruit 8 pixel font needs ~1820 bytes in FLASH
+#define LOAD_FONT2  // Font 2. Small 16 pixel high font, needs ~3534 bytes in FLASH, 96 characters
+#define LOAD_FONT4  // Font 4. Medium 26 pixel high font, needs ~5848 bytes in FLASH, 96 characters
+#define LOAD_FONT6  // Font 6. Large 48 pixel font, needs ~2666 bytes in FLASH, only characters 1234567890:-.apm
+#define LOAD_FONT7  // Font 7. 7 segment 48 pixel font, needs ~2438 bytes in FLASH, only characters 1234567890:-.
+#define LOAD_FONT8  // Font 8. Large 75 pixel font needs ~3256 bytes in FLASH, only characters 1234567890:-.
+//#define LOAD_FONT8N // Font 8. Alternative to Font 8 above, slightly narrower, so 3 digits fit a 160 pixel TFT
+#define LOAD_GFXFF  // FreeFonts. Include access to the 48 Adafruit_GFX free fonts FF1 to FF48 and custom fonts
+
+// Comment out the #define below to stop the SPIFFS filing system and smooth font code being loaded
+// this will save ~20kbytes of FLASH
+#define SMOOTH_FONT
+
+
+// ##################################################################################
+//
+// Section 4. Other options
+//
+// ##################################################################################
+
+// Define the SPI clock frequency, this affects the graphics rendering speed. Too
+// fast and the TFT driver will not keep up and display corruption appears.
+// With an ILI9341 display 40MHz works OK, 80MHz sometimes fails
+// With a ST7735 display more than 27MHz may not work (spurious pixels and lines)
+// With an ILI9163 display 27 MHz works OK.
+
+// #define SPI_FREQUENCY   1000000
+//#define SPI_FREQUENCY   5000000
+// #define SPI_FREQUENCY  10000000
+// #define SPI_FREQUENCY  20000000
+#define SPI_FREQUENCY  27000000 // Marauder // Actually sets it to 26.67MHz = 80/3
+// #define SPI_FREQUENCY  40000000
+// #define SPI_FREQUENCY  80000000
+
+// Optional reduced SPI frequency for reading TFT
+#define SPI_READ_FREQUENCY  20000000
+
+// The XPT2046 requires a lower SPI clock rate of 2.5MHz so we define that here:
+#define SPI_TOUCH_FREQUENCY  2500000
+
+// The ESP32 has 2 free SPI ports i.e. VSPI and HSPI, the VSPI is the default.
+// If the VSPI port is in use and pins are not accessible (e.g. TTGO T-Beam)
+// then uncomment the following line:
+#define USE_HSPI_PORT
+
+// Comment out the following #define if "SPI Transactions" do not need to be
+// supported. When commented out the code size will be smaller and sketches will
+// run slightly faster, so leave it commented out unless you need it!
+
+// Transaction support is needed to work with SD library but not needed with TFT_SdFat
+// Transaction support is required if other SPI devices are connected.
+
+// Transactions are automatically enabled by the library for an ESP32 (to use HAL mutex)
+// so changing it here has no effect
+
+// #define SUPPORT_TRANSACTIONS

User_Setup_cyd_guition.h

@@ -0,0 +1,316 @@
+//                            USER DEFINED SETTINGS
+//   Set driver type, fonts to be loaded, pins used and SPI control method etc
+//
+//   See the User_Setup_Select.h file if you wish to be able to define multiple
+//   setups and then easily select which setup file is used by the compiler.
+//
+//   If this file is edited correctly then all the library example sketches should
+//   run without the need to make any more changes for a particular hardware setup!
+//   Note that some sketches are designed for a particular TFT pixel width/height
+
+
+// ##################################################################################
+//
+// Section 1. Call up the right driver file and any options for it
+//
+// ##################################################################################
+
+// Display type -  only define if RPi display
+//#define RPI_DRIVER
+
+// Only define one driver, the other ones must be commented out
+#define ILI9341_DRIVER // OG Marauder
+//#define ST7735_DRIVER    // Marauder Mini  // Define additional parameters below for this display
+//#define ILI9163_DRIVER     // Define additional parameters below for this display
+//#define S6D02A1_DRIVER
+//#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
+//#define HX8357D_DRIVER
+//#define ILI9481_DRIVER
+//#define ILI9486_DRIVER
+//#define ILI9488_DRIVER     // WARNING: Do not connect ILI9488 display SDO to MISO if other devices share the SPI bus (TFT SDO does NOT tristate when CS is high)
+//#define ST7789_DRIVER      // Full configuration option, define additional parameters below for this display
+//#define ST7789_2_DRIVER    // Minimal configuration option, define additional parameters below for this display
+//#define R61581_DRIVER
+//#define RM68140_DRIVER
+//#define ST7796_DRIVER
+
+// Some displays support SPI reads via the MISO pin, other displays have a single
+// bi-directional SDA pin and the library will try to read this via the MOSI line.
+// To use the SDA line for reading data from the TFT uncomment the following line:
+
+// #define TFT_SDA_READ      // This option is for ESP32 ONLY, tested with ST7789 display only
+
+// For ST7789 and ILI9341 ONLY, define the colour order IF the blue and red are swapped on your display
+// Try ONE option at a time to find the correct colour order for your display
+
+//  #define TFT_RGB_ORDER TFT_RGB  // Colour order Red-Green-Blue
+//  #define TFT_RGB_ORDER TFT_BGR  // Colour order Blue-Green-Red
+
+// For M5Stack ESP32 module with integrated ILI9341 display ONLY, remove // in line below
+
+// #define M5STACK
+
+// For ST7789, ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation
+// #define TFT_WIDTH  80
+// #define TFT_WIDTH  128 // Marauder Mini
+ #define TFT_WIDTH  240 // ST7789 240 x 240 and 240 x 320
+// #define TFT_HEIGHT 160
+// #define TFT_HEIGHT 128 // Marauder Mini
+// #define TFT_HEIGHT 240 // ST7789 240 x 240
+ #define TFT_HEIGHT 320 // ST7789 240 x 320
+
+// For ST7735 ONLY, define the type of display, originally this was based on the
+// colour of the tab on the screen protector film but this is not always true, so try
+// out the different options below if the screen does not display graphics correctly,
+// e.g. colours wrong, mirror images, or tray pixels at the edges.
+// Comment out ALL BUT ONE of these options for a ST7735 display driver, save this
+// this User_Setup file, then rebuild and upload the sketch to the board again:
+
+// #define ST7735_INITB
+// #define ST7735_GREENTAB
+// #define ST7735_GREENTAB2
+// #define ST7735_GREENTAB3
+// #define ST7735_GREENTAB128    // For 128 x 128 display
+// #define ST7735_GREENTAB160x80 // For 160 x 80 display (BGR, inverted, 26 offset)
+// #define ST7735_REDTAB
+// #define ST7735_BLACKTAB
+// #define ST7735_REDTAB160x80   // For 160 x 80 display with 24 pixel offset
+
+// If colours are inverted (white shows as black) then uncomment one of the next
+// 2 lines try both options, one of the options should correct the inversion.
+
+// #define TFT_INVERSION_ON
+// #define TFT_INVERSION_OFF
+
+// If a backlight control signal is available then define the TFT_BL pin in Section 2
+// below. The backlight will be turned ON when tft.begin() is called, but the library
+// needs to know if the LEDs are ON with the pin HIGH or LOW. If the LEDs are to be
+// driven with a PWM signal or turned OFF/ON then this must be handled by the user
+// sketch. e.g. with digitalWrite(TFT_BL, LOW);
+
+// #define TFT_BACKLIGHT_ON LOW  // HIGH or LOW are options
+
+// ##################################################################################
+//
+// Section 2. Define the pins that are used to interface with the display here
+//
+// ##################################################################################
+
+// We must use hardware SPI, a minimum of 3 GPIO pins is needed.
+// Typical setup for ESP8266 NodeMCU ESP-12 is :
+//
+// Display SDO/MISO  to NodeMCU pin D6 (or leave disconnected if not reading TFT)
+// Display LED       to NodeMCU pin VIN (or 5V, see below)
+// Display SCK       to NodeMCU pin D5
+// Display SDI/MOSI  to NodeMCU pin D7
+// Display DC (RS/AO)to NodeMCU pin D3
+// Display RESET     to NodeMCU pin D4 (or RST, see below)
+// Display CS        to NodeMCU pin D8 (or GND, see below)
+// Display GND       to NodeMCU pin GND (0V)
+// Display VCC       to NodeMCU 5V or 3.3V
+//
+// The TFT RESET pin can be connected to the NodeMCU RST pin or 3.3V to free up a control pin
+//
+// The DC (Data Command) pin may be labeled AO or RS (Register Select)
+//
+// With some displays such as the ILI9341 the TFT CS pin can be connected to GND if no more
+// SPI devices (e.g. an SD Card) are connected, in this case comment out the #define TFT_CS
+// line below so it is NOT defined. Other displays such at the ST7735 require the TFT CS pin
+// to be toggled during setup, so in these cases the TFT_CS line must be defined and connected.
+//
+// The NodeMCU D0 pin can be used for RST
+//
+//
+// Note: only some versions of the NodeMCU provide the USB 5V on the VIN pin
+// If 5V is not available at a pin you can use 3.3V but backlight brightness
+// will be lower.
+
+
+// ###### EDIT THE PIN NUMBERS IN THE LINES FOLLOWING TO SUIT YOUR ESP8266 SETUP ######
+
+// For NodeMCU - use pin numbers in the form PIN_Dx where Dx is the NodeMCU pin designation
+//#define TFT_CS   PIN_D8  // Chip select control pin D8
+//#define TFT_DC   PIN_D3  // Data Command control pin
+//#define TFT_RST  PIN_D4  // Reset pin (could connect to NodeMCU RST, see next line)
+//#define TFT_RST  -1    // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
+
+//#define TFT_BL PIN_D1  // LED back-light (only for ST7789 with backlight control pin)
+
+//#define TOUCH_CS PIN_D2     // Chip select pin (T_CS) of touch screen
+
+//#define TFT_WR PIN_D2       // Write strobe for modified Raspberry Pi TFT only
+
+
+// ######  FOR ESP8266 OVERLAP MODE EDIT THE PIN NUMBERS IN THE FOLLOWING LINES  ######
+
+// Overlap mode shares the ESP8266 FLASH SPI bus with the TFT so has a performance impact
+// but saves pins for other functions. It is best not to connect MISO as some displays
+// do not tristate that line wjen chip select is high!
+// On NodeMCU 1.0 SD0=MISO, SD1=MOSI, CLK=SCLK to connect to TFT in overlap mode
+// On NodeMCU V3  S0 =MISO, S1 =MOSI, S2 =SCLK
+// In ESP8266 overlap mode the following must be defined
+
+//#define TFT_SPI_OVERLAP
+
+// In ESP8266 overlap mode the TFT chip select MUST connect to pin D3
+//#define TFT_CS   PIN_D3
+//#define TFT_DC   PIN_D5  // Data Command control pin
+//#define TFT_RST  PIN_D4  // Reset pin (could connect to NodeMCU RST, see next line)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
+
+
+// ###### EDIT THE PIN NUMBERS IN THE LINES FOLLOWING TO SUIT YOUR ESP32 SETUP   ######
+
+// For ESP32 Dev board (only tested with ILI9341 display)
+// The hardware SPI can be mapped to any pins
+
+// Marauder Mini
+/*
+#define TFT_CS   17  // Chip select control pin D8
+#define TFT_DC   16  // Data Command control pin
+#define TFT_RST  5  // Reset pin (could connect to NodeMCU RST, see next line)
+//#define TFT_MISO 19
+//#define TFT_MOSI 23
+//#define TFT_SCLK 18
+//#define TFT_BL   32
+*/
+
+// ESP32 Marauder 
+#define TFT_MISO 12
+#define TFT_MOSI 13
+#define TFT_SCLK 14
+#define TFT_CS   15  // Chip select control pin
+#define TFT_DC   2  // Data Command control pin
+#define TFT_RST   -1  // Reset pin (could connect to RST pin)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if display RESET is connected to ESP32 board RST
+
+#define TFT_BL   27  // LED back-light (only for ST7789 with backlight control pin)
+
+#define TOUCH_CS   33     // Chip select pin (T_CS) of touch screen
+
+/////////////////////////////
+
+// ESP32 Centauri
+/*
+#define TFT_MISO 19
+#define TFT_MOSI 23
+#define TFT_SCLK 18
+#define TFT_CS   27  // Chip select control pin
+#define TFT_DC   26  // Data Command control pin
+#define TFT_RST   5  // Reset pin (could connect to RST pin)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if display RESET is connected to ESP32 board RST
+
+#define TFT_BL   32  // LED back-light (only for ST7789 with backlight control pin)
+
+#define TOUCH_CS 21     // Chip select pin (T_CS) of touch screen
+*/
+/////////////////////////////
+
+//#define TFT_WR 22    // Write strobe for modified Raspberry Pi TFT only
+
+// For the M5Stack module use these #define lines
+//#define TFT_MISO 19
+//#define TFT_MOSI 23
+//#define TFT_SCLK 18
+//#define TFT_CS   14  // Chip select control pin
+//#define TFT_DC   27  // Data Command control pin
+//#define TFT_RST  33  // Reset pin (could connect to Arduino RESET pin)
+//#define TFT_BL   32  // LED back-light (required for M5Stack)
+
+// ######       EDIT THE PINs BELOW TO SUIT YOUR ESP32 PARALLEL TFT SETUP        ######
+
+// The library supports 8 bit parallel TFTs with the ESP32, the pin
+// selection below is compatible with ESP32 boards in UNO format.
+// Wemos D32 boards need to be modified, see diagram in Tools folder.
+// Only ILI9481 and ILI9341 based displays have been tested!
+
+// Parallel bus is only supported on ESP32
+// Uncomment line below to use ESP32 Parallel interface instead of SPI
+
+//#define ESP32_PARALLEL
+
+// The ESP32 and TFT the pins used for testing are:
+//#define TFT_CS   33  // Chip select control pin (library pulls permanently low
+//#define TFT_DC   15  // Data Command control pin - must use a pin in the range 0-31
+//#define TFT_RST  32  // Reset pin, toggles on startup
+
+//#define TFT_WR    4  // Write strobe control pin - must use a pin in the range 0-31
+//#define TFT_RD    2  // Read strobe control pin
+
+//#define TFT_D0   12  // Must use pins in the range 0-31 for the data bus
+//#define TFT_D1   13  // so a single register write sets/clears all bits.
+//#define TFT_D2   26  // Pins can be randomly assigned, this does not affect
+//#define TFT_D3   25  // TFT screen update performance.
+//#define TFT_D4   17
+//#define TFT_D5   16
+//#define TFT_D6   27
+//#define TFT_D7   14
+
+
+// ##################################################################################
+//
+// Section 3. Define the fonts that are to be used here
+//
+// ##################################################################################
+
+// Comment out the #defines below with // to stop that font being loaded
+// The ESP8366 and ESP32 have plenty of memory so commenting out fonts is not
+// normally necessary. If all fonts are loaded the extra FLASH space required is
+// about 17Kbytes. To save FLASH space only enable the fonts you need!
+
+#define LOAD_GLCD   // Font 1. Original Adafruit 8 pixel font needs ~1820 bytes in FLASH
+#define LOAD_FONT2  // Font 2. Small 16 pixel high font, needs ~3534 bytes in FLASH, 96 characters
+#define LOAD_FONT4  // Font 4. Medium 26 pixel high font, needs ~5848 bytes in FLASH, 96 characters
+#define LOAD_FONT6  // Font 6. Large 48 pixel font, needs ~2666 bytes in FLASH, only characters 1234567890:-.apm
+#define LOAD_FONT7  // Font 7. 7 segment 48 pixel font, needs ~2438 bytes in FLASH, only characters 1234567890:-.
+#define LOAD_FONT8  // Font 8. Large 75 pixel font needs ~3256 bytes in FLASH, only characters 1234567890:-.
+//#define LOAD_FONT8N // Font 8. Alternative to Font 8 above, slightly narrower, so 3 digits fit a 160 pixel TFT
+#define LOAD_GFXFF  // FreeFonts. Include access to the 48 Adafruit_GFX free fonts FF1 to FF48 and custom fonts
+
+// Comment out the #define below to stop the SPIFFS filing system and smooth font code being loaded
+// this will save ~20kbytes of FLASH
+#define SMOOTH_FONT
+
+
+// ##################################################################################
+//
+// Section 4. Other options
+//
+// ##################################################################################
+
+// Define the SPI clock frequency, this affects the graphics rendering speed. Too
+// fast and the TFT driver will not keep up and display corruption appears.
+// With an ILI9341 display 40MHz works OK, 80MHz sometimes fails
+// With a ST7735 display more than 27MHz may not work (spurious pixels and lines)
+// With an ILI9163 display 27 MHz works OK.
+
+// #define SPI_FREQUENCY   1000000
+//#define SPI_FREQUENCY   5000000
+// #define SPI_FREQUENCY  10000000
+// #define SPI_FREQUENCY  20000000
+#define SPI_FREQUENCY  27000000 // Marauder // Actually sets it to 26.67MHz = 80/3
+// #define SPI_FREQUENCY  40000000
+// #define SPI_FREQUENCY  80000000
+
+// Optional reduced SPI frequency for reading TFT
+#define SPI_READ_FREQUENCY  20000000
+
+// The XPT2046 requires a lower SPI clock rate of 2.5MHz so we define that here:
+#define SPI_TOUCH_FREQUENCY  2500000
+
+// The ESP32 has 2 free SPI ports i.e. VSPI and HSPI, the VSPI is the default.
+// If the VSPI port is in use and pins are not accessible (e.g. TTGO T-Beam)
+// then uncomment the following line:
+#define USE_HSPI_PORT
+
+// Comment out the following #define if "SPI Transactions" do not need to be
+// supported. When commented out the code size will be smaller and sketches will
+// run slightly faster, so leave it commented out unless you need it!
+
+// Transaction support is needed to work with SD library but not needed with TFT_SdFat
+// Transaction support is required if other SPI devices are connected.
+
+// Transactions are automatically enabled by the library for an ESP32 (to use HAL mutex)
+// so changing it here has no effect
+
+// #define SUPPORT_TRANSACTIONS

User_Setup_cyd_micro.h

@@ -0,0 +1,316 @@
+//                            USER DEFINED SETTINGS
+//   Set driver type, fonts to be loaded, pins used and SPI control method etc
+//
+//   See the User_Setup_Select.h file if you wish to be able to define multiple
+//   setups and then easily select which setup file is used by the compiler.
+//
+//   If this file is edited correctly then all the library example sketches should
+//   run without the need to make any more changes for a particular hardware setup!
+//   Note that some sketches are designed for a particular TFT pixel width/height
+
+
+// ##################################################################################
+//
+// Section 1. Call up the right driver file and any options for it
+//
+// ##################################################################################
+
+// Display type -  only define if RPi display
+//#define RPI_DRIVER
+
+// Only define one driver, the other ones must be commented out
+#define ILI9341_DRIVER // OG Marauder
+//#define ST7735_DRIVER    // Marauder Mini  // Define additional parameters below for this display
+//#define ILI9163_DRIVER     // Define additional parameters below for this display
+//#define S6D02A1_DRIVER
+//#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
+//#define HX8357D_DRIVER
+//#define ILI9481_DRIVER
+//#define ILI9486_DRIVER
+//#define ILI9488_DRIVER     // WARNING: Do not connect ILI9488 display SDO to MISO if other devices share the SPI bus (TFT SDO does NOT tristate when CS is high)
+//#define ST7789_DRIVER      // Full configuration option, define additional parameters below for this display
+//#define ST7789_2_DRIVER    // Minimal configuration option, define additional parameters below for this display
+//#define R61581_DRIVER
+//#define RM68140_DRIVER
+//#define ST7796_DRIVER
+
+// Some displays support SPI reads via the MISO pin, other displays have a single
+// bi-directional SDA pin and the library will try to read this via the MOSI line.
+// To use the SDA line for reading data from the TFT uncomment the following line:
+
+// #define TFT_SDA_READ      // This option is for ESP32 ONLY, tested with ST7789 display only
+
+// For ST7789 and ILI9341 ONLY, define the colour order IF the blue and red are swapped on your display
+// Try ONE option at a time to find the correct colour order for your display
+
+//  #define TFT_RGB_ORDER TFT_RGB  // Colour order Red-Green-Blue
+//  #define TFT_RGB_ORDER TFT_BGR  // Colour order Blue-Green-Red
+
+// For M5Stack ESP32 module with integrated ILI9341 display ONLY, remove // in line below
+
+// #define M5STACK
+
+// For ST7789, ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation
+// #define TFT_WIDTH  80
+// #define TFT_WIDTH  128 // Marauder Mini
+ #define TFT_WIDTH  240 // ST7789 240 x 240 and 240 x 320
+// #define TFT_HEIGHT 160
+// #define TFT_HEIGHT 128 // Marauder Mini
+// #define TFT_HEIGHT 240 // ST7789 240 x 240
+ #define TFT_HEIGHT 320 // ST7789 240 x 320
+
+// For ST7735 ONLY, define the type of display, originally this was based on the
+// colour of the tab on the screen protector film but this is not always true, so try
+// out the different options below if the screen does not display graphics correctly,
+// e.g. colours wrong, mirror images, or tray pixels at the edges.
+// Comment out ALL BUT ONE of these options for a ST7735 display driver, save this
+// this User_Setup file, then rebuild and upload the sketch to the board again:
+
+// #define ST7735_INITB
+// #define ST7735_GREENTAB
+// #define ST7735_GREENTAB2
+// #define ST7735_GREENTAB3
+// #define ST7735_GREENTAB128    // For 128 x 128 display
+// #define ST7735_GREENTAB160x80 // For 160 x 80 display (BGR, inverted, 26 offset)
+// #define ST7735_REDTAB
+// #define ST7735_BLACKTAB
+// #define ST7735_REDTAB160x80   // For 160 x 80 display with 24 pixel offset
+
+// If colours are inverted (white shows as black) then uncomment one of the next
+// 2 lines try both options, one of the options should correct the inversion.
+
+// #define TFT_INVERSION_ON
+// #define TFT_INVERSION_OFF
+
+// If a backlight control signal is available then define the TFT_BL pin in Section 2
+// below. The backlight will be turned ON when tft.begin() is called, but the library
+// needs to know if the LEDs are ON with the pin HIGH or LOW. If the LEDs are to be
+// driven with a PWM signal or turned OFF/ON then this must be handled by the user
+// sketch. e.g. with digitalWrite(TFT_BL, LOW);
+
+// #define TFT_BACKLIGHT_ON LOW  // HIGH or LOW are options
+
+// ##################################################################################
+//
+// Section 2. Define the pins that are used to interface with the display here
+//
+// ##################################################################################
+
+// We must use hardware SPI, a minimum of 3 GPIO pins is needed.
+// Typical setup for ESP8266 NodeMCU ESP-12 is :
+//
+// Display SDO/MISO  to NodeMCU pin D6 (or leave disconnected if not reading TFT)
+// Display LED       to NodeMCU pin VIN (or 5V, see below)
+// Display SCK       to NodeMCU pin D5
+// Display SDI/MOSI  to NodeMCU pin D7
+// Display DC (RS/AO)to NodeMCU pin D3
+// Display RESET     to NodeMCU pin D4 (or RST, see below)
+// Display CS        to NodeMCU pin D8 (or GND, see below)
+// Display GND       to NodeMCU pin GND (0V)
+// Display VCC       to NodeMCU 5V or 3.3V
+//
+// The TFT RESET pin can be connected to the NodeMCU RST pin or 3.3V to free up a control pin
+//
+// The DC (Data Command) pin may be labeled AO or RS (Register Select)
+//
+// With some displays such as the ILI9341 the TFT CS pin can be connected to GND if no more
+// SPI devices (e.g. an SD Card) are connected, in this case comment out the #define TFT_CS
+// line below so it is NOT defined. Other displays such at the ST7735 require the TFT CS pin
+// to be toggled during setup, so in these cases the TFT_CS line must be defined and connected.
+//
+// The NodeMCU D0 pin can be used for RST
+//
+//
+// Note: only some versions of the NodeMCU provide the USB 5V on the VIN pin
+// If 5V is not available at a pin you can use 3.3V but backlight brightness
+// will be lower.
+
+
+// ###### EDIT THE PIN NUMBERS IN THE LINES FOLLOWING TO SUIT YOUR ESP8266 SETUP ######
+
+// For NodeMCU - use pin numbers in the form PIN_Dx where Dx is the NodeMCU pin designation
+//#define TFT_CS   PIN_D8  // Chip select control pin D8
+//#define TFT_DC   PIN_D3  // Data Command control pin
+//#define TFT_RST  PIN_D4  // Reset pin (could connect to NodeMCU RST, see next line)
+//#define TFT_RST  -1    // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
+
+//#define TFT_BL PIN_D1  // LED back-light (only for ST7789 with backlight control pin)
+
+//#define TOUCH_CS PIN_D2     // Chip select pin (T_CS) of touch screen
+
+//#define TFT_WR PIN_D2       // Write strobe for modified Raspberry Pi TFT only
+
+
+// ######  FOR ESP8266 OVERLAP MODE EDIT THE PIN NUMBERS IN THE FOLLOWING LINES  ######
+
+// Overlap mode shares the ESP8266 FLASH SPI bus with the TFT so has a performance impact
+// but saves pins for other functions. It is best not to connect MISO as some displays
+// do not tristate that line wjen chip select is high!
+// On NodeMCU 1.0 SD0=MISO, SD1=MOSI, CLK=SCLK to connect to TFT in overlap mode
+// On NodeMCU V3  S0 =MISO, S1 =MOSI, S2 =SCLK
+// In ESP8266 overlap mode the following must be defined
+
+//#define TFT_SPI_OVERLAP
+
+// In ESP8266 overlap mode the TFT chip select MUST connect to pin D3
+//#define TFT_CS   PIN_D3
+//#define TFT_DC   PIN_D5  // Data Command control pin
+//#define TFT_RST  PIN_D4  // Reset pin (could connect to NodeMCU RST, see next line)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
+
+
+// ###### EDIT THE PIN NUMBERS IN THE LINES FOLLOWING TO SUIT YOUR ESP32 SETUP   ######
+
+// For ESP32 Dev board (only tested with ILI9341 display)
+// The hardware SPI can be mapped to any pins
+
+// Marauder Mini
+/*
+#define TFT_CS   17  // Chip select control pin D8
+#define TFT_DC   16  // Data Command control pin
+#define TFT_RST  5  // Reset pin (could connect to NodeMCU RST, see next line)
+//#define TFT_MISO 19
+//#define TFT_MOSI 23
+//#define TFT_SCLK 18
+//#define TFT_BL   32
+*/
+
+// ESP32 Marauder 
+#define TFT_MISO 12
+#define TFT_MOSI 13
+#define TFT_SCLK 14
+#define TFT_CS   15  // Chip select control pin
+#define TFT_DC   2  // Data Command control pin
+#define TFT_RST   -1  // Reset pin (could connect to RST pin)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if display RESET is connected to ESP32 board RST
+
+#define TFT_BL   21  // LED back-light (only for ST7789 with backlight control pin)
+
+#define TOUCH_CS   33     // Chip select pin (T_CS) of touch screen
+
+/////////////////////////////
+
+// ESP32 Centauri
+/*
+#define TFT_MISO 19
+#define TFT_MOSI 23
+#define TFT_SCLK 18
+#define TFT_CS   27  // Chip select control pin
+#define TFT_DC   26  // Data Command control pin
+#define TFT_RST   5  // Reset pin (could connect to RST pin)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if display RESET is connected to ESP32 board RST
+
+#define TFT_BL   32  // LED back-light (only for ST7789 with backlight control pin)
+
+#define TOUCH_CS 21     // Chip select pin (T_CS) of touch screen
+*/
+/////////////////////////////
+
+//#define TFT_WR 22    // Write strobe for modified Raspberry Pi TFT only
+
+// For the M5Stack module use these #define lines
+//#define TFT_MISO 19
+//#define TFT_MOSI 23
+//#define TFT_SCLK 18
+//#define TFT_CS   14  // Chip select control pin
+//#define TFT_DC   27  // Data Command control pin
+//#define TFT_RST  33  // Reset pin (could connect to Arduino RESET pin)
+//#define TFT_BL   32  // LED back-light (required for M5Stack)
+
+// ######       EDIT THE PINs BELOW TO SUIT YOUR ESP32 PARALLEL TFT SETUP        ######
+
+// The library supports 8 bit parallel TFTs with the ESP32, the pin
+// selection below is compatible with ESP32 boards in UNO format.
+// Wemos D32 boards need to be modified, see diagram in Tools folder.
+// Only ILI9481 and ILI9341 based displays have been tested!
+
+// Parallel bus is only supported on ESP32
+// Uncomment line below to use ESP32 Parallel interface instead of SPI
+
+//#define ESP32_PARALLEL
+
+// The ESP32 and TFT the pins used for testing are:
+//#define TFT_CS   33  // Chip select control pin (library pulls permanently low
+//#define TFT_DC   15  // Data Command control pin - must use a pin in the range 0-31
+//#define TFT_RST  32  // Reset pin, toggles on startup
+
+//#define TFT_WR    4  // Write strobe control pin - must use a pin in the range 0-31
+//#define TFT_RD    2  // Read strobe control pin
+
+//#define TFT_D0   12  // Must use pins in the range 0-31 for the data bus
+//#define TFT_D1   13  // so a single register write sets/clears all bits.
+//#define TFT_D2   26  // Pins can be randomly assigned, this does not affect
+//#define TFT_D3   25  // TFT screen update performance.
+//#define TFT_D4   17
+//#define TFT_D5   16
+//#define TFT_D6   27
+//#define TFT_D7   14
+
+
+// ##################################################################################
+//
+// Section 3. Define the fonts that are to be used here
+//
+// ##################################################################################
+
+// Comment out the #defines below with // to stop that font being loaded
+// The ESP8366 and ESP32 have plenty of memory so commenting out fonts is not
+// normally necessary. If all fonts are loaded the extra FLASH space required is
+// about 17Kbytes. To save FLASH space only enable the fonts you need!
+
+#define LOAD_GLCD   // Font 1. Original Adafruit 8 pixel font needs ~1820 bytes in FLASH
+#define LOAD_FONT2  // Font 2. Small 16 pixel high font, needs ~3534 bytes in FLASH, 96 characters
+#define LOAD_FONT4  // Font 4. Medium 26 pixel high font, needs ~5848 bytes in FLASH, 96 characters
+#define LOAD_FONT6  // Font 6. Large 48 pixel font, needs ~2666 bytes in FLASH, only characters 1234567890:-.apm
+#define LOAD_FONT7  // Font 7. 7 segment 48 pixel font, needs ~2438 bytes in FLASH, only characters 1234567890:-.
+#define LOAD_FONT8  // Font 8. Large 75 pixel font needs ~3256 bytes in FLASH, only characters 1234567890:-.
+//#define LOAD_FONT8N // Font 8. Alternative to Font 8 above, slightly narrower, so 3 digits fit a 160 pixel TFT
+#define LOAD_GFXFF  // FreeFonts. Include access to the 48 Adafruit_GFX free fonts FF1 to FF48 and custom fonts
+
+// Comment out the #define below to stop the SPIFFS filing system and smooth font code being loaded
+// this will save ~20kbytes of FLASH
+#define SMOOTH_FONT
+
+
+// ##################################################################################
+//
+// Section 4. Other options
+//
+// ##################################################################################
+
+// Define the SPI clock frequency, this affects the graphics rendering speed. Too
+// fast and the TFT driver will not keep up and display corruption appears.
+// With an ILI9341 display 40MHz works OK, 80MHz sometimes fails
+// With a ST7735 display more than 27MHz may not work (spurious pixels and lines)
+// With an ILI9163 display 27 MHz works OK.
+
+// #define SPI_FREQUENCY   1000000
+//#define SPI_FREQUENCY   5000000
+// #define SPI_FREQUENCY  10000000
+// #define SPI_FREQUENCY  20000000
+#define SPI_FREQUENCY  27000000 // Marauder // Actually sets it to 26.67MHz = 80/3
+// #define SPI_FREQUENCY  40000000
+// #define SPI_FREQUENCY  80000000
+
+// Optional reduced SPI frequency for reading TFT
+#define SPI_READ_FREQUENCY  20000000
+
+// The XPT2046 requires a lower SPI clock rate of 2.5MHz so we define that here:
+#define SPI_TOUCH_FREQUENCY  2500000
+
+// The ESP32 has 2 free SPI ports i.e. VSPI and HSPI, the VSPI is the default.
+// If the VSPI port is in use and pins are not accessible (e.g. TTGO T-Beam)
+// then uncomment the following line:
+#define USE_HSPI_PORT
+
+// Comment out the following #define if "SPI Transactions" do not need to be
+// supported. When commented out the code size will be smaller and sketches will
+// run slightly faster, so leave it commented out unless you need it!
+
+// Transaction support is needed to work with SD library but not needed with TFT_SdFat
+// Transaction support is required if other SPI devices are connected.
+
+// Transactions are automatically enabled by the library for an ESP32 (to use HAL mutex)
+// so changing it here has no effect
+
+// #define SUPPORT_TRANSACTIONS

User_Setup_pocket_sdr_3.h

@@ -0,0 +1,330 @@
+//                            USER DEFINED SETTINGS
+//   Set driver type, fonts to be loaded, pins used and SPI control method etc
+//
+//   See the User_Setup_Select.h file if you wish to be able to define multiple
+//   setups and then easily select which setup file is used by the compiler.
+//
+//   If this file is edited correctly then all the library example sketches should
+//   run without the need to make any more changes for a particular hardware setup!
+//   Note that some sketches are designed for a particular TFT pixel width/height
+
+
+// ##################################################################################
+//
+// Section 1. Call up the right driver file and any options for it
+//
+// ##################################################################################
+
+// Display type -  only define if RPi display
+//#define RPI_DRIVER
+
+// Only define one driver, the other ones must be commented out
+//#define ILI9341_DRIVER // OG Marauder
+#define ST7735_DRIVER    // Marauder Mini  // Define additional parameters below for this display
+//#define ILI9163_DRIVER     // Define additional parameters below for this display
+//#define S6D02A1_DRIVER
+//#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
+//#define HX8357D_DRIVER
+//#define ILI9481_DRIVER
+//#define ILI9486_DRIVER
+//#define ILI9488_DRIVER     // WARNING: Do not connect ILI9488 display SDO to MISO if other devices share the SPI bus (TFT SDO does NOT tristate when CS is high)
+//#define ST7789_DRIVER      // Full configuration option, define additional parameters below for this display
+//#define ST7789_2_DRIVER    // Minimal configuration option, define additional parameters below for this display
+//#define R61581_DRIVER
+//#define RM68140_DRIVER
+//#define ST7796_DRIVER
+
+// Some displays support SPI reads via the MISO pin, other displays have a single
+// bi-directional SDA pin and the library will try to read this via the MOSI line.
+// To use the SDA line for reading data from the TFT uncomment the following line:
+
+// #define TFT_SDA_READ      // This option is for ESP32 ONLY, tested with ST7789 display only
+
+// For ST7789 and ILI9341 ONLY, define the colour order IF the blue and red are swapped on your display
+// Try ONE option at a time to find the correct colour order for your display
+
+//  #define TFT_RGB_ORDER TFT_RGB  // Colour order Red-Green-Blue
+  #define TFT_RGB_ORDER TFT_BGR  // Colour order Blue-Green-Red
+
+// For M5Stack ESP32 module with integrated ILI9341 display ONLY, remove // in line below
+
+// #define M5STACK
+
+// For ST7789, ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation
+ #define TFT_WIDTH  80
+// #define TFT_WIDTH  128 // Marauder Mini
+// #define TFT_WIDTH  240 // ST7789 240 x 240 and 240 x 320
+ #define TFT_HEIGHT 160
+// #define TFT_HEIGHT 128 // Marauder Mini
+// #define TFT_HEIGHT 240 // ST7789 240 x 240
+// #define TFT_HEIGHT 320 // ST7789 240 x 320
+
+// For ST7735 ONLY, define the type of display, originally this was based on the
+// colour of the tab on the screen protector film but this is not always true, so try
+// out the different options below if the screen does not display graphics correctly,
+// e.g. colours wrong, mirror images, or tray pixels at the edges.
+// Comment out ALL BUT ONE of these options for a ST7735 display driver, save this
+// this User_Setup file, then rebuild and upload the sketch to the board again:
+
+// #define ST7735_INITB
+// #define ST7735_GREENTAB
+// #define ST7735_GREENTAB2
+// #define ST7735_GREENTAB3
+// #define ST7735_GREENTAB128    // For 128 x 128 display
+// #define ST7735_GREENTAB160x80 // For 160 x 80 display (BGR, inverted, 26 offset)
+// #define ST7735_REDTAB
+// #define ST7735_BLACKTAB
+ #define ST7735_REDTAB160x80   // For 160 x 80 display with 24 pixel offset
+
+// If colours are inverted (white shows as black) then uncomment one of the next
+// 2 lines try both options, one of the options should correct the inversion.
+
+// #define TFT_INVERSION_ON
+ #define TFT_INVERSION_OFF
+
+// If a backlight control signal is available then define the TFT_BL pin in Section 2
+// below. The backlight will be turned ON when tft.begin() is called, but the library
+// needs to know if the LEDs are ON with the pin HIGH or LOW. If the LEDs are to be
+// driven with a PWM signal or turned OFF/ON then this must be handled by the user
+// sketch. e.g. with digitalWrite(TFT_BL, LOW);
+
+ #define TFT_BACKLIGHT_ON LOW  // HIGH or LOW are options
+
+// ##################################################################################
+//
+// Section 2. Define the pins that are used to interface with the display here
+//
+// ##################################################################################
+
+// We must use hardware SPI, a minimum of 3 GPIO pins is needed.
+// Typical setup for ESP8266 NodeMCU ESP-12 is :
+//
+// Display SDO/MISO  to NodeMCU pin D6 (or leave disconnected if not reading TFT)
+// Display LED       to NodeMCU pin VIN (or 5V, see below)
+// Display SCK       to NodeMCU pin D5
+// Display SDI/MOSI  to NodeMCU pin D7
+// Display DC (RS/AO)to NodeMCU pin D3
+// Display RESET     to NodeMCU pin D4 (or RST, see below)
+// Display CS        to NodeMCU pin D8 (or GND, see below)
+// Display GND       to NodeMCU pin GND (0V)
+// Display VCC       to NodeMCU 5V or 3.3V
+//
+// The TFT RESET pin can be connected to the NodeMCU RST pin or 3.3V to free up a control pin
+//
+// The DC (Data Command) pin may be labeled AO or RS (Register Select)
+//
+// With some displays such as the ILI9341 the TFT CS pin can be connected to GND if no more
+// SPI devices (e.g. an SD Card) are connected, in this case comment out the #define TFT_CS
+// line below so it is NOT defined. Other displays such at the ST7735 require the TFT CS pin
+// to be toggled during setup, so in these cases the TFT_CS line must be defined and connected.
+//
+// The NodeMCU D0 pin can be used for RST
+//
+//
+// Note: only some versions of the NodeMCU provide the USB 5V on the VIN pin
+// If 5V is not available at a pin you can use 3.3V but backlight brightness
+// will be lower.
+
+
+// ###### EDIT THE PIN NUMBERS IN THE LINES FOLLOWING TO SUIT YOUR ESP8266 SETUP ######
+
+// For NodeMCU - use pin numbers in the form PIN_Dx where Dx is the NodeMCU pin designation
+//#define TFT_CS   PIN_D8  // Chip select control pin D8
+//#define TFT_DC   PIN_D3  // Data Command control pin
+//#define TFT_RST  PIN_D4  // Reset pin (could connect to NodeMCU RST, see next line)
+//#define TFT_RST  -1    // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
+
+//#define TFT_BL PIN_D1  // LED back-light (only for ST7789 with backlight control pin)
+
+//#define TOUCH_CS PIN_D2     // Chip select pin (T_CS) of touch screen
+
+//#define TFT_WR PIN_D2       // Write strobe for modified Raspberry Pi TFT only
+
+
+// ######  FOR ESP8266 OVERLAP MODE EDIT THE PIN NUMBERS IN THE FOLLOWING LINES  ######
+
+// Overlap mode shares the ESP8266 FLASH SPI bus with the TFT so has a performance impact
+// but saves pins for other functions. It is best not to connect MISO as some displays
+// do not tristate that line wjen chip select is high!
+// On NodeMCU 1.0 SD0=MISO, SD1=MOSI, CLK=SCLK to connect to TFT in overlap mode
+// On NodeMCU V3  S0 =MISO, S1 =MOSI, S2 =SCLK
+// In ESP8266 overlap mode the following must be defined
+
+//#define TFT_SPI_OVERLAP
+
+// In ESP8266 overlap mode the TFT chip select MUST connect to pin D3
+//#define TFT_CS   PIN_D3
+//#define TFT_DC   PIN_D5  // Data Command control pin
+//#define TFT_RST  PIN_D4  // Reset pin (could connect to NodeMCU RST, see next line)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
+
+
+// ###### EDIT THE PIN NUMBERS IN THE LINES FOLLOWING TO SUIT YOUR ESP32 SETUP   ######
+
+// For ESP32 Dev board (only tested with ILI9341 display)
+// The hardware SPI can be mapped to any pins
+
+// Marauder Mini
+// Drone Detector v1
+
+#define TFT_CS   23  // Chip select control pin D8
+#define TFT_DC   24  // Data Command control pin
+#define TFT_RST  -1  // Reset pin (could connect to NodeMCU RST, see next line)
+#define TOUCH_CS -1
+//#define TFT_MISO 16
+#define TFT_MOSI 7
+#define TFT_SCLK 6
+#define TFT_BL   27
+
+
+// Drone Detector v2
+/*
+#define TFT_CS   17  // Chip select control pin D8
+#define TFT_DC   26  // Data Command control pin
+#define TFT_RST  -1  // Reset pin (could connect to NodeMCU RST, see next line)
+#define TOUCH_CS -1
+//#define TFT_MISO 16
+#define TFT_MOSI 23
+#define TFT_SCLK 18
+#define TFT_BL   32
+*/
+/*
+// ESP32 Marauder 
+#define TFT_MISO 19
+#define TFT_MOSI 23
+#define TFT_SCLK 18
+#define TFT_CS   17  // Chip select control pin
+#define TFT_DC   16  // Data Command control pin
+#define TFT_RST   5  // Reset pin (could connect to RST pin)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if display RESET is connected to ESP32 board RST
+
+#define TFT_BL   32  // LED back-light (only for ST7789 with backlight control pin)
+
+#define TOUCH_CS 21     // Chip select pin (T_CS) of touch screen
+*/
+/////////////////////////////
+
+// ESP32 Centauri
+/*
+#define TFT_MISO 19
+#define TFT_MOSI 23
+#define TFT_SCLK 18
+#define TFT_CS   27  // Chip select control pin
+#define TFT_DC   26  // Data Command control pin
+#define TFT_RST   5  // Reset pin (could connect to RST pin)
+//#define TFT_RST  -1  // Set TFT_RST to -1 if display RESET is connected to ESP32 board RST
+
+#define TFT_BL   32  // LED back-light (only for ST7789 with backlight control pin)
+
+#define TOUCH_CS 21     // Chip select pin (T_CS) of touch screen
+*/
+/////////////////////////////
+
+//#define TFT_WR 22    // Write strobe for modified Raspberry Pi TFT only
+
+// For the M5Stack module use these #define lines
+//#define TFT_MISO 19
+//#define TFT_MOSI 23
+//#define TFT_SCLK 18
+//#define TFT_CS   14  // Chip select control pin
+//#define TFT_DC   27  // Data Command control pin
+//#define TFT_RST  33  // Reset pin (could connect to Arduino RESET pin)
+//#define TFT_BL   32  // LED back-light (required for M5Stack)
+
+// ######       EDIT THE PINs BELOW TO SUIT YOUR ESP32 PARALLEL TFT SETUP        ######
+
+// The library supports 8 bit parallel TFTs with the ESP32, the pin
+// selection below is compatible with ESP32 boards in UNO format.
+// Wemos D32 boards need to be modified, see diagram in Tools folder.
+// Only ILI9481 and ILI9341 based displays have been tested!
+
+// Parallel bus is only supported on ESP32
+// Uncomment line below to use ESP32 Parallel interface instead of SPI
+
+//#define ESP32_PARALLEL
+
+// The ESP32 and TFT the pins used for testing are:
+//#define TFT_CS   33  // Chip select control pin (library pulls permanently low
+//#define TFT_DC   15  // Data Command control pin - must use a pin in the range 0-31
+//#define TFT_RST  32  // Reset pin, toggles on startup
+
+//#define TFT_WR    4  // Write strobe control pin - must use a pin in the range 0-31
+//#define TFT_RD    2  // Read strobe control pin
+
+//#define TFT_D0   12  // Must use pins in the range 0-31 for the data bus
+//#define TFT_D1   13  // so a single register write sets/clears all bits.
+//#define TFT_D2   26  // Pins can be randomly assigned, this does not affect
+//#define TFT_D3   25  // TFT screen update performance.
+//#define TFT_D4   17
+//#define TFT_D5   16
+//#define TFT_D6   27
+//#define TFT_D7   14
+
+
+// ##################################################################################
+//
+// Section 3. Define the fonts that are to be used here
+//
+// ##################################################################################
+
+// Comment out the #defines below with // to stop that font being loaded
+// The ESP8366 and ESP32 have plenty of memory so commenting out fonts is not
+// normally necessary. If all fonts are loaded the extra FLASH space required is
+// about 17Kbytes. To save FLASH space only enable the fonts you need!
+
+#define LOAD_GLCD   // Font 1. Original Adafruit 8 pixel font needs ~1820 bytes in FLASH
+#define LOAD_FONT2  // Font 2. Small 16 pixel high font, needs ~3534 bytes in FLASH, 96 characters
+#define LOAD_FONT4  // Font 4. Medium 26 pixel high font, needs ~5848 bytes in FLASH, 96 characters
+#define LOAD_FONT6  // Font 6. Large 48 pixel font, needs ~2666 bytes in FLASH, only characters 1234567890:-.apm
+#define LOAD_FONT7  // Font 7. 7 segment 48 pixel font, needs ~2438 bytes in FLASH, only characters 1234567890:-.
+#define LOAD_FONT8  // Font 8. Large 75 pixel font needs ~3256 bytes in FLASH, only characters 1234567890:-.
+//#define LOAD_FONT8N // Font 8. Alternative to Font 8 above, slightly narrower, so 3 digits fit a 160 pixel TFT
+#define LOAD_GFXFF  // FreeFonts. Include access to the 48 Adafruit_GFX free fonts FF1 to FF48 and custom fonts
+
+// Comment out the #define below to stop the SPIFFS filing system and smooth font code being loaded
+// this will save ~20kbytes of FLASH
+#define SMOOTH_FONT
+
+
+// ##################################################################################
+//
+// Section 4. Other options
+//
+// ##################################################################################
+
+// Define the SPI clock frequency, this affects the graphics rendering speed. Too
+// fast and the TFT driver will not keep up and display corruption appears.
+// With an ILI9341 display 40MHz works OK, 80MHz sometimes fails
+// With a ST7735 display more than 27MHz may not work (spurious pixels and lines)
+// With an ILI9163 display 27 MHz works OK.
+
+// #define SPI_FREQUENCY   1000000
+//#define SPI_FREQUENCY   5000000
+// #define SPI_FREQUENCY  10000000
+// #define SPI_FREQUENCY  20000000
+#define SPI_FREQUENCY  27000000 // Marauder // Actually sets it to 26.67MHz = 80/3
+// #define SPI_FREQUENCY  40000000
+// #define SPI_FREQUENCY  80000000
+
+// Optional reduced SPI frequency for reading TFT
+//#define SPI_READ_FREQUENCY  20000000
+
+// The XPT2046 requires a lower SPI clock rate of 2.5MHz so we define that here:
+//#define SPI_TOUCH_FREQUENCY  2500000
+
+// The ESP32 has 2 free SPI ports i.e. VSPI and HSPI, the VSPI is the default.
+// If the VSPI port is in use and pins are not accessible (e.g. TTGO T-Beam)
+// then uncomment the following line:
+//#define USE_HSPI_PORT
+
+// Comment out the following #define if "SPI Transactions" do not need to be
+// supported. When commented out the code size will be smaller and sketches will
+// run slightly faster, so leave it commented out unless you need it!
+
+// Transaction support is needed to work with SD library but not needed with TFT_SdFat
+// Transaction support is required if other SPI devices are connected.
+
+// Transactions are automatically enabled by the library for an ESP32 (to use HAL mutex)
+// so changing it here has no effect
+
+// #define SUPPORT_TRANSACTIONS

esp32_marauder/Assets.h

@@ -215,7 +215,19 @@ PROGMEM static const unsigned char menu_icons[][66] = {
     0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 
     0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 
     0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 
-    0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF}
+    0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF},
+    {0xFF, 0xFF, 0x3F, 0xFF, 0xF7, 0x3F, 0x7F, 0x96, 0x3F, 0xFF, 0xED, 0x3F, // PINESCAN_SNIFF: 37
+    0x3F, 0x25, 0x3F, 0xDF, 0xD2, 0x3E, 0xFF, 0xED, 0x3F, 0x7F, 0x8E, 0x3F, 
+    0x3B, 0x77, 0x37, 0xBD, 0x6A, 0x2F, 0xD6, 0xBD, 0x1A, 0xDA, 0xDA, 0x16, 
+    0x5A, 0x6F, 0x16, 0x9A, 0xF7, 0x16, 0xD6, 0x5A, 0x1A, 0xDD, 0xBD, 0x2E, 
+    0xBB, 0x5A, 0x37, 0x3F, 0x6F, 0x3F, 0x7F, 0xB7, 0x3F, 0xFF, 0xCC, 0x3F, 
+    0xFF, 0xF3, 0x3F, 0xFF, 0xFF, 0x3F},
+    {0xFF, 0xFF, 0xFF, 0xFF, 0x07, 0xFF, 0xFF, 0xFC, 0xFF, 0xF3, 0x87, 0xF7, // JOINED: 38
+    0x7F, 0xEE, 0xFF, 0xED, 0xC7, 0xDD, 0xBF, 0xDB, 0x7F, 0xDB, 0x67, 0xDB, 
+    0x67, 0xDB, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF},
+    {0xFF, 0xFF, 0x1F, 0xF8, 0x0F, 0xF0, 0x07, 0xE0, 0x07, 0xE0, 0x07, 0xE0, // FORCE: 39
+    0x67, 0xE6, 0x77, 0xEE, 0x87, 0xE0, 0x8F, 0xF1, 0x0F, 0xF0, 0x4F, 0xF5, 
+    0x1F, 0xF8, 0x3F, 0xFC, 0xFF, 0xFF, 0xFF, 0xFF}
 };
 
 /*#ifndef MARAUDER_MINI

esp32_marauder/CommandLine.cpp

@@ -221,6 +221,8 @@ void CommandLine::runCommand(String input) {
     // WiFi sniff/scan
     Serial.println(HELP_EVIL_PORTAL_CMD);
     Serial.println(HELP_PACKET_COUNT_CMD);
+    Serial.println(HELP_PING_CMD);
+    Serial.println(HELP_PORT_SCAN_CMD);
     Serial.println(HELP_SIGSTREN_CMD);
     Serial.println(HELP_SCAN_ALL_CMD);
     Serial.println(HELP_SCANAP_CMD);
@@ -229,6 +231,8 @@ void CommandLine::runCommand(String input) {
     Serial.println(HELP_SNIFF_BEACON_CMD);
     Serial.println(HELP_SNIFF_PROBE_CMD);
     Serial.println(HELP_SNIFF_PWN_CMD);
+    Serial.println(HELP_SNIFF_PINESCAN_CMD);
+    Serial.println(HELP_SNIFF_MULTISSID_CMD);
     Serial.println(HELP_SNIFF_ESP_CMD);
     Serial.println(HELP_SNIFF_DEAUTH_CMD);
     Serial.println(HELP_SNIFF_PMKID_CMD);
@@ -246,11 +250,13 @@ void CommandLine::runCommand(String input) {
     Serial.println(HELP_LIST_AP_CMD_B);
     Serial.println(HELP_LIST_AP_CMD_C);
     Serial.println(HELP_LIST_AP_CMD_D);
+    Serial.println(HELP_LIST_AP_CMD_E);
     Serial.println(HELP_SEL_CMD_A);
     Serial.println(HELP_SSID_CMD_A);
     Serial.println(HELP_SSID_CMD_B);
     Serial.println(HELP_SAVE_CMD);
     Serial.println(HELP_LOAD_CMD);
+    Serial.println(HELP_JOIN_CMD);
     
     // Bluetooth sniff/scan
     #ifdef HAS_BT
@@ -280,9 +286,16 @@ void CommandLine::runCommand(String input) {
     //  web_obj.shutdownServer();
     //  return;
     //}
+
+    int f_arg = this->argSearch(&cmd_args, "-f");
     
     uint8_t old_scan_mode=wifi_scan_obj.currentScanMode;
 
+    if (f_arg != -1) {
+      WiFi.disconnect(true);
+      delay(100);
+    }
+
     wifi_scan_obj.StartScan(WIFI_SCAN_OFF);
 
     if(old_scan_mode == WIFI_SCAN_GPS_NMEA)
@@ -683,6 +696,24 @@ void CommandLine::runCommand(String input) {
       #endif
       wifi_scan_obj.StartScan(WIFI_SCAN_PWN, TFT_MAGENTA);
     }
+    // PineScan sniff
+    else if (cmd_args.get(0) == SNIFF_PINESCAN_CMD) {
+      Serial.println("Starting Pinescan sniff. Stop with " + (String)STOPSCAN_CMD);
+      #ifdef HAS_SCREEN
+        display_obj.clearScreen();
+        menu_function_obj.drawStatusBar();
+      #endif
+      wifi_scan_obj.StartScan(WIFI_SCAN_PINESCAN, TFT_MAGENTA);
+    }
+    // MultiSSID sniff
+    else if (cmd_args.get(0) == SNIFF_MULTISSID_CMD) {
+      Serial.println("Starting MultiSSID sniff. Stop with " + (String)STOPSCAN_CMD);
+      #ifdef HAS_SCREEN
+        display_obj.clearScreen();
+        menu_function_obj.drawStatusBar();
+      #endif
+      wifi_scan_obj.StartScan(WIFI_SCAN_MULTISSID, TFT_MAGENTA);
+    }
     // Espressif sniff
     else if (cmd_args.get(0) == SNIFF_ESP_CMD) {
       Serial.println("Starting Espressif device sniff. Stop with " + (String)STOPSCAN_CMD);
@@ -1140,6 +1171,52 @@ void CommandLine::runCommand(String input) {
     }
   }
 
+  if (wifi_scan_obj.wifi_connected) {
+    // Ping Scan
+    if (cmd_args.get(0) == PING_CMD) {
+      Serial.println("Starting Ping Scan. Stop with " + (String)STOPSCAN_CMD);
+      #ifdef HAS_SCREEN
+        display_obj.clearScreen();
+        menu_function_obj.drawStatusBar();
+      #endif
+      wifi_scan_obj.StartScan(WIFI_PING_SCAN, TFT_GREEN);
+    }
+
+    // Port Scan
+    if (cmd_args.get(0) == PORT_SCAN_CMD) {
+      int all_sw = this->argSearch(&cmd_args, "-a");
+      int ip_sw = this->argSearch(&cmd_args, "-t");
+
+      // Check they specified ip index
+      if (ip_sw != -1) {
+        int ip_index = cmd_args.get(ip_sw + 1).toInt();
+
+        // Check provided index is in list
+        if (ip_index < ipList->size()) {
+
+          // Full port scan
+          if (all_sw != -1) {
+            Serial.println("Selected: " + ipList->get(ip_index).toString());
+            wifi_scan_obj.current_scan_ip = ipList->get(ip_index);
+            #ifdef HAS_SCREEN
+              display_obj.clearScreen();
+              menu_function_obj.drawStatusBar();
+            #endif
+            wifi_scan_obj.StartScan(WIFI_PORT_SCAN_ALL, TFT_BLUE);
+          }
+        }
+        else {
+          Serial.println("The IP index specified is out of range");
+          return;
+        }
+      }
+      else {
+        Serial.println("You did not specify an IP index");
+        return;
+      }
+    }
+  }
+
 
   int count_selected = 0;
   //// WiFi aux commands
@@ -1149,6 +1226,7 @@ void CommandLine::runCommand(String input) {
     int ss_sw = this->argSearch(&cmd_args, "-s");
     int cl_sw = this->argSearch(&cmd_args, "-c");
     int at_sw = this->argSearch(&cmd_args, "-t");
+    int ip_sw = this->argSearch(&cmd_args, "-i");
 
     // List APs
     if (ap_sw != -1) {
@@ -1162,6 +1240,12 @@ void CommandLine::runCommand(String input) {
       }
       this->showCounts(count_selected);
     }
+    // List IPs
+    else if (ip_sw != -1) {
+      for (int i = 0; i < ipList->size(); i++) {
+        Serial.println("[" + (String)i + "] " + ipList->get(i).toString());
+      }
+    }
     // List SSIDs
     else if (ss_sw != -1) {
       for (int i = 0; i < ssids->size(); i++) {
@@ -1221,6 +1305,28 @@ void CommandLine::runCommand(String input) {
       wifi_scan_obj.RunInfo();
     }
   }
+  else if (cmd_args.get(0) == JOIN_CMD) {
+    int ap_sw = this->argSearch(&cmd_args, "-a");
+    int pw_sw = this->argSearch(&cmd_args, "-p");
+
+    if ((ap_sw != -1) && (pw_sw != -1)) {
+      int index = cmd_args.get(ap_sw + 1).toInt();
+      String password = cmd_args.get(pw_sw + 1);
+      Serial.println("Using SSID: " + (String)access_points->get(index).essid + " Password: " + (String)password);
+      //wifi_scan_obj.currentScanMode = LV_JOIN_WIFI;
+      //wifi_scan_obj.StartScan(LV_JOIN_WIFI, TFT_YELLOW); 
+      wifi_scan_obj.joinWiFi(access_points->get(index).essid, password, false);
+      #ifdef HAS_SCREEN
+        #ifdef HAS_MINI_KB
+          menu_function_obj.changeMenu(menu_function_obj.current_menu);
+        #endif
+      #endif
+    }
+    else {
+      Serial.println("You did not provide the proper args");
+      return;
+    }
+  }
   // Select access points or stations
   else if (cmd_args.get(0) == SEL_CMD) {
     // Get switches

esp32_marauder/CommandLine.h

@@ -34,6 +34,7 @@ extern LinkedList<AccessPoint>* access_points;
 extern LinkedList<AirTag>* airtags;
 extern LinkedList<ssid>* ssids;
 extern LinkedList<Station>* stations;
+extern LinkedList<IPAddress>* ipList;
 extern const String PROGMEM version_number;
 extern const String PROGMEM board_target;
 
@@ -63,11 +64,15 @@ const char PROGMEM SNIFF_RAW_CMD[] = "sniffraw";
 const char PROGMEM SNIFF_BEACON_CMD[] = "sniffbeacon";
 const char PROGMEM SNIFF_PROBE_CMD[] = "sniffprobe";
 const char PROGMEM SNIFF_PWN_CMD[] = "sniffpwn";
+const char PROGMEM SNIFF_PINESCAN_CMD[] = "sniffpinescan";
+const char PROGMEM SNIFF_MULTISSID_CMD[] = "sniffmultissid";
 const char PROGMEM SNIFF_ESP_CMD[] = "sniffesp";
 const char PROGMEM SNIFF_DEAUTH_CMD[] = "sniffdeauth";
 const char PROGMEM SNIFF_PMKID_CMD[] = "sniffpmkid";
 const char PROGMEM STOPSCAN_CMD[] = "stopscan";
 const char PROGMEM WARDRIVE_CMD[] = "wardrive";
+const char PROGMEM PING_CMD[] = "pingscan";
+const char PROGMEM PORT_SCAN_CMD[] = "portscan";
 
 // WiFi attack
 const char PROGMEM ATTACK_CMD[] = "attack";
@@ -83,6 +88,7 @@ const char PROGMEM SEL_CMD[] = "select";
 const char PROGMEM SSID_CMD[] = "ssid";
 const char PROGMEM SAVE_CMD[] = "save";
 const char PROGMEM LOAD_CMD[] = "load";
+const char PROGMEM JOIN_CMD[] = "join";
 
 // Bluetooth sniff/scan
 const char PROGMEM BT_SPAM_CMD[] = "blespam";
@@ -121,11 +127,15 @@ const char PROGMEM HELP_SNIFF_RAW_CMD[] = "sniffraw";
 const char PROGMEM HELP_SNIFF_BEACON_CMD[] = "sniffbeacon";
 const char PROGMEM HELP_SNIFF_PROBE_CMD[] = "sniffprobe";
 const char PROGMEM HELP_SNIFF_PWN_CMD[] = "sniffpwn";
+const char PROGMEM HELP_SNIFF_PINESCAN_CMD[] = "sniffpinescan";
+const char PROGMEM HELP_SNIFF_MULTISSID_CMD[] = "sniffmultissid";
 const char PROGMEM HELP_SNIFF_ESP_CMD[] = "sniffesp";
 const char PROGMEM HELP_SNIFF_DEAUTH_CMD[] = "sniffdeauth";
 const char PROGMEM HELP_SNIFF_PMKID_CMD[] = "sniffpmkid [-c <channel>][-d][-l]";
-const char PROGMEM HELP_STOPSCAN_CMD[] = "stopscan";
+const char PROGMEM HELP_STOPSCAN_CMD[] = "stopscan [-f]";
 const char PROGMEM HELP_WARDRIVE_CMD[] = "wardrive [-s]";
+const char PROGMEM HELP_PING_CMD[] = "pingscan";
+const char PROGMEM HELP_PORT_SCAN_CMD[] = "portscan [-a] -t <ip index>";
 
 // WiFi attack
 const char PROGMEM HELP_ATTACK_CMD[] = "attack -t <beacon [-l/-r/-a]/deauth [-c]/[-s <src mac>] [-d <dst mac>]/probe/rickroll>";
@@ -135,12 +145,14 @@ const char PROGMEM HELP_LIST_AP_CMD_A[] = "list -s";
 const char PROGMEM HELP_LIST_AP_CMD_B[] = "list -a";
 const char PROGMEM HELP_LIST_AP_CMD_C[] = "list -c";
 const char PROGMEM HELP_LIST_AP_CMD_D[] = "list -t";
+const char PROGMEM HELP_LIST_AP_CMD_E[] = "list -i";
 const char PROGMEM HELP_INFO_CMD[] = "info [-a <index>]";
 const char PROGMEM HELP_SEL_CMD_A[] = "select -a/-s/-c <index (comma separated)>/-f \"equals <String> or contains <String>\"";
 const char PROGMEM HELP_SSID_CMD_A[] = "ssid -a [-g <count>/-n <name>]";
 const char PROGMEM HELP_SSID_CMD_B[] = "ssid -r <index>";
 const char PROGMEM HELP_SAVE_CMD[] = "save -a/-s";
 const char PROGMEM HELP_LOAD_CMD[] = "load -a/-s";
+const char PROGMEM HELP_JOIN_CMD[] = "join -a <index> -p <password>";
 
 // Bluetooth sniff/scan
 const char PROGMEM HELP_BT_SNIFF_CMD[] = "sniffbt [-t] <airtag/flipper>";

esp32_marauder/Display.cpp

@@ -4,9 +4,111 @@
 #ifdef HAS_SCREEN
 
 Display::Display()
+#ifdef HAS_CYD_TOUCH
+  : touchscreenSPI(VSPI),
+    touchscreen(XPT2046_CS, XPT2046_IRQ)
+#endif
 {
 }
 
+int8_t Display::menuButton(uint16_t *x, uint16_t *y, bool pressed, bool check_hold) {
+  #ifdef HAS_ILI9341
+    for (uint8_t b = BUTTON_ARRAY_LEN; b < BUTTON_ARRAY_LEN + 3; b++) {
+      if (pressed && this->key[b].contains(*x, *y)) {
+        this->key[b].press(true);  // tell the button it is pressed
+      } else {
+        this->key[b].press(false);  // tell the button it is NOT pressed
+      }
+    }
+
+    for (uint8_t b = BUTTON_ARRAY_LEN; b < BUTTON_ARRAY_LEN + 3; b++) {
+      if (!check_hold) {
+        if ((this->key[b].justReleased()) && (!pressed)) {
+          return b - BUTTON_ARRAY_LEN;
+        }
+      }
+      else {
+        if ((this->key[b].isPressed())) {
+          return b - BUTTON_ARRAY_LEN;
+        }
+      }
+    }
+
+  #endif
+
+  return -1;
+}
+
+uint8_t Display::updateTouch(uint16_t *x, uint16_t *y, uint16_t threshold) {
+  #ifdef HAS_ILI9341
+    if (!this->headless_mode)
+      #ifndef HAS_CYD_TOUCH
+        return this->tft.getTouch(x, y, threshold);
+      #else
+        if (this->touchscreen.tirqTouched() && this->touchscreen.touched()) {
+          TS_Point p = this->touchscreen.getPoint();
+
+          //*x = map(p.x, 200, 3700, 1, TFT_WIDTH);
+          //*y = map(p.y, 240, 3800, 1, TFT_HEIGHT);
+
+          uint8_t rot = this->tft.getRotation();
+
+          //#ifdef HAS_CYD_PORTRAIT
+          //  rot = 0;
+          //#endif
+
+          switch (rot) {
+            case 0: // Standard Protrait
+              *x = map(p.x, 200, 3700, 1, TFT_WIDTH);
+              *y = map(p.y, 240, 3800, 1, TFT_HEIGHT);
+              break;
+            case 1:
+              *x = map(p.y, 143, 3715, 0, TFT_HEIGHT);     // Horizontal (Y axis in touch, X on screen)
+              *y = map(p.x, 3786, 216, 0, TFT_WIDTH);    // Vertical (X axis in touch, Y on screen)
+              break;
+            case 2:
+              *x = map(p.x, 3700, 200, 1, TFT_WIDTH);
+              *y = map(p.y, 3800, 240, 1, TFT_HEIGHT);
+              break;
+            case 3:
+              *x = map(p.y, 3800, 240, 1, TFT_WIDTH);
+              *y = map(p.x, 200, 3700, 1, TFT_HEIGHT);
+              break;
+          }
+          return 1;
+        }
+        else
+          return 0;
+      #endif
+    else
+      return !this->headless_mode;
+  #endif
+
+  return 0;
+}
+
+bool Display::isTouchHeld(uint16_t threshold) {
+  static unsigned long touchStartTime = 0;
+  static bool touchHeld = false;
+  uint16_t x, y;
+
+  if (this->updateTouch(&x, &y, threshold)) {
+    // Touch detected
+    if (touchStartTime == 0) {
+      touchStartTime = millis();  // First touch timestamp
+    } else if (!touchHeld && millis() - touchStartTime >= 1000) {
+      touchHeld = true;  // Held for at least 1000ms
+      return true;
+    }
+  } else {
+    // Touch released
+    touchStartTime = 0;
+    touchHeld = false;
+  }
+
+  return false;
+}
+
 // Function to prepare the display and the menus
 void Display::RunSetup()
 {
@@ -18,32 +120,47 @@ void Display::RunSetup()
   #ifdef SCREEN_BUFFER
     screen_buffer = new LinkedList<String>();
   #endif
+
+  #ifdef HAS_CYD_TOUCH
+    this->touchscreenSPI.begin(XPT2046_CLK, XPT2046_MISO, XPT2046_MOSI, XPT2046_CS);
+    this->touchscreen.begin(touchscreenSPI);
+    this->touchscreen.setRotation(0);
+  #endif
   
   tft.init();
-  #ifndef MARAUDER_M5STICKC
+
+  tft.setRotation(SCREEN_ORIENTATION);
+
+  /*#ifndef MARAUDER_M5STICKC
     tft.setRotation(0); // Portrait
   #endif
 
+  #ifdef HAS_CYD_PORTRAIT
+    tft.setRotation(3); // Bro these CYDs are so stupid
+  #endif
+
   #ifdef MARAUDER_M5STICKC
     tft.setRotation(1);
   #endif
 
   #ifdef MARAUDER_REV_FEATHER
     tft.setRotation(1);
-  #endif
+  #endif*/
 
   tft.setCursor(0, 0);
 
   #ifdef HAS_ILI9341
 
-    #ifdef TFT_SHIELD
-      uint16_t calData[5] = { 275, 3494, 361, 3528, 4 }; // tft.setRotation(0); // Portrait with TFT Shield
-      //Serial.println(F("Using TFT Shield"));
-    #else if defined(TFT_DIY)
-      uint16_t calData[5] = { 339, 3470, 237, 3438, 2 }; // tft.setRotation(0); // Portrait with DIY TFT
-      //Serial.println(F("Using TFT DIY"));
+    #ifndef HAS_CYD_TOUCH
+      #ifdef TFT_SHIELD
+        uint16_t calData[5] = { 275, 3494, 361, 3528, 4 }; // tft.setRotation(0); // Portrait with TFT Shield
+        //Serial.println(F("Using TFT Shield"));
+      #elif defined(TFT_DIY)
+        uint16_t calData[5] = { 339, 3470, 237, 3438, 2 }; // tft.setRotation(0); // Portrait with DIY TFT
+        //Serial.println(F("Using TFT DIY"));
+      #endif
+      tft.setTouch(calData);
     #endif
-    tft.setTouch(calData);
 
   #endif
 
@@ -476,7 +593,11 @@ void Display::setupScrollArea(uint16_t tfa, uint16_t bfa) {
   //Serial.println("   bfa: " + (String)bfa);
   //Serial.println("yStart: " + (String)this->yStart);
   #ifdef HAS_ILI9341
-    tft.writecommand(ILI9341_VSCRDEF); // Vertical scroll definition
+    #ifdef HAS_ST7789
+      tft.writecommand(ST7789_VSCRDEF); // Vertical scroll definition
+    #else
+      tft.writecommand(ILI9341_VSCRDEF);
+    #endif
     tft.writedata(tfa >> 8);           // Top Fixed Area line count
     tft.writedata(tfa);
     tft.writedata((YMAX-tfa-bfa)>>8);  // Vertical Scrolling Area line count
@@ -489,7 +610,11 @@ void Display::setupScrollArea(uint16_t tfa, uint16_t bfa) {
 
 void Display::scrollAddress(uint16_t vsp) {
   #ifdef HAS_ILI9341
-    tft.writecommand(ILI9341_VSCRSADD); // Vertical scrolling pointer
+    #ifdef HAS_ST7789
+      tft.writecommand(ST7789_VSCRDEF); // Vertical scroll definition
+    #else
+      tft.writecommand(ILI9341_VSCRDEF);
+    #endif
     tft.writedata(vsp>>8);
     tft.writedata(vsp);
   #endif

esp32_marauder/Display.h

@@ -19,6 +19,10 @@
 
 #include <TFT_eSPI.h>
 
+#ifdef HAS_CYD_TOUCH
+  #include <XPT2046_Touchscreen.h>
+#endif
+
 // WiFi stuff
 #define OTA_UPDATE 100
 #define SHOW_INFO 101
@@ -45,6 +49,10 @@
 #define MAGENTA_KEY ";mgn;"
 #define WHITE_KEY ";wht;"
 
+#define UP_BUTTON     0
+#define SELECT_BUTTON 1
+#define DOWN_BUTTON   2
+
 class Display
 {
   private:
@@ -69,9 +77,14 @@ class Display
   public:
     Display();
     TFT_eSPI tft = TFT_eSPI();
-    TFT_eSPI_Button key[BUTTON_ARRAY_LEN];
+    TFT_eSPI_Button key[BUTTON_ARRAY_LEN + 3];
     const String PROGMEM version_number = MARAUDER_VERSION;
 
+    #ifdef HAS_CYD_TOUCH
+      SPIClass touchscreenSPI;
+      XPT2046_Touchscreen touchscreen;
+    #endif
+
     bool printing = false;
     bool loading = false;
     bool tteBar = false;
@@ -105,6 +118,9 @@ class Display
     // We can speed up scrolling of short text lines by just blanking the character we drew
     int blank[19]; // We keep all the strings pixel lengths to optimise the speed of the top line blanking
 
+    int8_t menuButton(uint16_t *x, uint16_t *y, bool pressed, bool check_hold = false);
+    uint8_t updateTouch(uint16_t *x, uint16_t *y, uint16_t threshold = 600);
+    bool isTouchHeld(uint16_t threshold = 600);
     void tftDrawRedOnOffButton();
     void tftDrawGreenOnOffButton();
     void tftDrawGraphObjects(byte x_scale);

esp32_marauder/EvilPortal.cpp

@@ -1,5 +1,9 @@
 #include "EvilPortal.h"
 
+#ifdef HAS_PSRAM
+  char* index_html = nullptr;
+#endif
+
 AsyncWebServer server(80);
 
 EvilPortal::EvilPortal() {
@@ -23,6 +27,13 @@ void EvilPortal::setup() {
   #endif
 }
 
+void EvilPortal::cleanup() {
+  #ifdef HAS_PSRAM
+    free(index_html);
+    index_html = nullptr;
+  #endif
+}
+
 bool EvilPortal::begin(LinkedList<ssid>* ssids, LinkedList<AccessPoint>* access_points) {
   if (!this->setAP(ssids, access_points))
     return false;
@@ -43,12 +54,50 @@ String EvilPortal::get_password() {
 }
 
 void EvilPortal::setupServer() {
-  server.on("/", HTTP_GET, [this](AsyncWebServerRequest *request) {
-    request->send_P(200, "text/html", index_html);
-    Serial.println("client connected");
-    #ifdef HAS_SCREEN
-      this->sendToDisplay("Client connected to server");
+  #ifndef HAS_PSRAM
+    server.on("/", HTTP_GET, [this](AsyncWebServerRequest *request) {
+      request->send_P(200, "text/html", index_html);
+      Serial.println("client connected");
+      #ifdef HAS_SCREEN
+        this->sendToDisplay("Client connected to server");
+      #endif
+    });
+  #else
+    server.on("/", HTTP_GET, [this](AsyncWebServerRequest *request) {
+      request->send(200, "text/html", index_html);
+      Serial.println("client connected");
+      #ifdef HAS_SCREEN
+        this->sendToDisplay("Client connected to server");
+      #endif
+    });
+  #endif
+
+  const char* captiveEndpoints[] = {
+    "/hotspot-detect.html",
+    "/library/test/success.html",
+    "/success.txt",
+    "/generate_204",
+    "/gen_204",
+    "/ncsi.txt",
+    "/connecttest.txt",
+    "/redirect"
+  };
+
+  for (int i = 0; i < sizeof(captiveEndpoints) / sizeof(captiveEndpoints[0]); i++) {
+    
+    #ifndef HAS_PSRAM
+      server.on(captiveEndpoints[i], HTTP_GET, [this](AsyncWebServerRequest *request){
+        request->send_P(200, "text/html", index_html);
+      });
+    #else
+      server.on(captiveEndpoints[i], HTTP_GET, [this](AsyncWebServerRequest *request){
+        request->send(200, "text/html", index_html);
+      });
     #endif
+  }
+
+  server.on("/get-ap-name", HTTP_GET, [this](AsyncWebServerRequest *request) {
+    request->send(200, "text/plain", WiFi.softAPSSID());
   });
 
   server.on("/get", HTTP_GET, [this](AsyncWebServerRequest *request) {
@@ -78,7 +127,13 @@ void EvilPortal::setupServer() {
 void EvilPortal::setHtmlFromSerial() {
   Serial.println("Setting HTML from serial...");
   const char *htmlStr = Serial.readString().c_str();
-  strncpy(index_html, htmlStr, strlen(htmlStr));
+  #ifdef HAS_PSRAM
+    index_html = (char*) ps_malloc(MAX_HTML_SIZE);
+  #endif
+  strlcpy(index_html, htmlStr, strlen(htmlStr));
+  #ifdef HAS_PSRAM
+    index_html[MAX_HTML_SIZE - 1] = '\0';
+  #endif
   this->has_html = true;
   this->using_serial_html = true;
   Serial.println("html set");
@@ -119,7 +174,13 @@ bool EvilPortal::setHtml() {
       if (isPrintable(c))
         html.concat(c);
     }
-    strncpy(index_html, html.c_str(), strlen(html.c_str()));
+    #ifdef HAS_PSRAM
+      index_html = (char*) ps_malloc(MAX_HTML_SIZE);
+    #endif
+    strlcpy(index_html, html.c_str(), strlen(html.c_str()));
+    #ifdef HAS_PSRAM
+      index_html[MAX_HTML_SIZE - 1] = '\0';
+    #endif
     this->has_html = true;
     Serial.println("html set");
     html_file.close();

esp32_marauder/EvilPortal.h

@@ -37,7 +37,12 @@ extern Buffer buffer_obj;
 #define WIFI_SCAN_EVIL_PORTAL 30
 
 char apName[MAX_AP_NAME_SIZE] = "PORTAL";
-char index_html[MAX_HTML_SIZE] = "TEST";
+
+#ifndef HAS_PSRAM
+  char index_html[MAX_HTML_SIZE] = "TEST";
+#else
+  extern char* index_html;
+#endif
 
 struct ssid {
   String essid;
@@ -51,7 +56,8 @@ struct AccessPoint {
   uint8_t channel;
   uint8_t bssid[6];
   bool selected;
-  LinkedList<char>* beacon;
+ // LinkedList<char>* beacon;
+  char beacon[2];
   int8_t rssi;
   LinkedList<uint16_t>* stations;
   uint16_t packets;
@@ -106,6 +112,7 @@ class EvilPortal {
 
     LinkedList<String>* html_files;
 
+    void cleanup();
     String get_user_name();
     String get_password();
     void setup();

esp32_marauder/MenuFunctions.h

@@ -74,6 +74,10 @@ extern Settings settings_obj;
 #define DISABLE_TOUCH 34
 #define FLIPPER 35
 #define BLANK 36
+#define PINESCAN_SNIFF 37 // Use blanks icon
+#define MULTISSID_SNIFF 37 // Use blanks icon
+#define JOINED 38
+#define FORCE 39
 
 PROGMEM void my_disp_flush(lv_disp_drv_t *disp, const lv_area_t *area, lv_color_t *color_p);
 PROGMEM bool my_touchpad_read(lv_indev_drv_t * indev_driver, lv_indev_data_t * data);
@@ -82,6 +86,7 @@ PROGMEM static lv_disp_buf_t disp_buf;
 PROGMEM static lv_color_t buf[LV_HOR_RES_MAX * 10];
 
 PROGMEM static void ta_event_cb(lv_obj_t * ta, lv_event_t event);
+PROGMEM static void join_wifi_keyboard_event_cb(lv_obj_t * keyboard, lv_event_t event);
 PROGMEM static void add_ssid_keyboard_event_cb(lv_obj_t * keyboard, lv_event_t event);
 PROGMEM static void html_list_cb(lv_obj_t * btn, lv_event_t event);
 PROGMEM static void ap_list_cb(lv_obj_t * btn, lv_event_t event);
@@ -161,18 +166,20 @@ class MenuFunctions
 
     // WiFi menu stuff
     Menu wifiSnifferMenu;
+    Menu wifiScannerMenu;
     Menu wifiAttackMenu;
     #ifdef HAS_GPS
       Menu wardrivingMenu;
     #endif
     Menu wifiGeneralMenu;
     Menu wifiAPMenu;
+    Menu wifiIPMenu;
     #ifdef HAS_BT
       Menu airtagMenu;
     #endif
-    #ifndef HAS_ILI9341
+    //#ifndef HAS_ILI9341
       Menu wifiStationMenu;
-    #endif
+    //#endif
 
     // WiFi General Menu
     Menu htmlMenu;
@@ -181,6 +188,7 @@ class MenuFunctions
     Menu genAPMacMenu;
     Menu cloneAPMacMenu;
     Menu setMacMenu;
+    Menu selectProbeSSIDsMenu;
 
     // Bluetooth menu stuff
     Menu bluetoothSnifferMenu;
@@ -193,7 +201,7 @@ class MenuFunctions
 
     // Menu icons
 
-
+    void displayMenuButtons();
     uint16_t getColor(uint16_t color);
     void drawAvgLine(int16_t value);
     void drawMaxLine(int16_t value, uint16_t color);
@@ -211,11 +219,9 @@ class MenuFunctions
     void displaySetting(String key, Menu* menu, int index);
     void buttonSelected(int b, int x = -1);
     void buttonNotSelected(int b, int x = -1);
-    #if (!defined(HAS_ILI9341) && defined(HAS_BUTTONS))
-      void miniKeyboard(Menu * targetMenu);
-    #endif
-
-    uint8_t updateTouch(uint16_t *x, uint16_t *y, uint16_t threshold = 600);
+    //#if (!defined(HAS_ILI9341) && defined(HAS_BUTTONS))
+      String miniKeyboard(Menu * targetMenu, bool do_pass = false);
+    //#endif
 
   public:
     MenuFunctions();
@@ -249,6 +255,7 @@ class MenuFunctions
 
     String loaded_file = "";
 
+    void joinWiFiGFX(String essid);
     void setGraphScale(float scale);
     void initLVGL();
     void deinitLVGL();

esp32_marauder/SDInterface.cpp

@@ -21,7 +21,7 @@ bool SDInterface::initSD() {
     pinMode(SD_CS, OUTPUT);
 
     delay(10);
-    #if defined(MARAUDER_M5STICKC)
+    #if (defined(MARAUDER_M5STICKC)) || (defined(HAS_CYD_TOUCH))
       /* Set up SPI SD Card using external pin header
       StickCPlus Header - SPI SD Card Reader
                   3v3   -   3v3
@@ -31,7 +31,13 @@ bool SDInterface::initSD() {
                   G26   -   MOSI
                         -   CS (jumper to SD Card GND Pin)
       */
-      enum { SPI_SCK = 0, SPI_MISO = 36, SPI_MOSI = 26 };
+      #if defined(MARAUDER_M5STICKC)
+        enum { SPI_SCK = 0, SPI_MISO = 36, SPI_MOSI = 26 };
+      #elif defined(HAS_CYD_TOUCH)
+        enum { SPI_SCK = SD_SCK, SPI_MISO = SD_MISO, SPI_MOSI = SD_MOSI };
+      #else
+        enum { SPI_SCK = 0, SPI_MISO = 36, SPI_MOSI = 26 };
+      #endif
       this->spiExt = new SPIClass();
       this->spiExt->begin(SPI_SCK, SPI_MISO, SPI_MOSI, SD_CS);
       if (!SD.begin(SD_CS, *(this->spiExt))) {

esp32_marauder/SDInterface.h

@@ -26,9 +26,9 @@ extern Settings settings_obj;
 class SDInterface {
 
   private:
-#if defined(MARAUDER_M5STICKC)
-  SPIClass *spiExt;
-#endif
+  #if (defined(MARAUDER_M5STICKC) || defined(HAS_CYD_TOUCH))
+    SPIClass *spiExt;
+  #endif
     bool checkDetectPin();
 
   public:

esp32_marauder/WiFiScan.h

@@ -11,10 +11,11 @@
 #include <vector>
 
 #ifdef HAS_BT
-  #include <NimBLEDevice.h>
+  #include <NimBLEDevice.h> // 1.3.8
 #endif
 
 #include <WiFi.h>
+#include <ESP32Ping.h>
 #include "EvilPortal.h"
 #include <math.h>
 #include "esp_wifi.h"
@@ -37,7 +38,7 @@
 #endif
 #include "settings.h"
 #include "Assets.h"
-#ifdef MARAUDER_FLIPPER
+#ifdef HAS_FLIPPER_LED
   #include "flipperLED.h"
 #elif defined(XIAO_ESP32_S3)
   #include "xiaoLED.h"
@@ -102,13 +103,27 @@
 #define BT_SCAN_ANALYZER 47
 #define WIFI_SCAN_PACKET_RATE 48
 #define WIFI_SCAN_AP_STA 49
+#define WIFI_SCAN_PINESCAN 50
+#define WIFI_SCAN_MULTISSID 51
+#define WIFI_CONNECTED 52
+#define WIFI_PING_SCAN 53
+#define WIFI_PORT_SCAN_ALL 54
 
 #define BASE_MULTIPLIER 4
 
 #define ANALYZER_NAME_REFRESH 100 // Number of events to refresh the name
 
+// PineScan and Multi SSID
+#define MULTISSID_THRESHOLD 3 // Threshold For Multi SSID
+#define MAX_MULTISSID_ENTRIES 100 // Max number of confirmed MultiSSIDs to store
+#define MAX_AP_ENTRIES 100 // Max number of APs to track for analysis
+#define MAX_DISPLAY_ENTRIES 1 // Max Unique MACs to display
+#define MAX_PINESCAN_ENTRIES 100 // PineScan Max Entries
+
 #define MAX_CHANNEL     14
 
+#define MAX_PORT 65535
+
 #define WIFI_SECURITY_OPEN   0
 #define WIFI_SECURITY_WEP    1
 #define WIFI_SECURITY_WPA    2
@@ -150,7 +165,7 @@ extern Buffer buffer_obj;
   extern BatteryInterface battery_obj;
 #endif
 extern Settings settings_obj;
-#ifdef MARAUDER_FLIPPER
+#ifdef HAS_FLIPPER_LED
   extern flipperLED flipper_led;
 #elif defined(XIAO_ESP32_S3)
   extern xiaoLED xiao_led;
@@ -201,11 +216,17 @@ struct Flipper {
   String name;
 };
 
+#ifdef HAS_PSRAM
+  extern struct mac_addr* mac_history;
+#endif
+
 class WiFiScan
 {
   private:
     // Wardriver thanks to https://github.com/JosephHewitt
-    struct mac_addr mac_history[mac_history_len];
+    #ifndef HAS_PSRAM
+      struct mac_addr mac_history[mac_history_len];
+    #endif
 
     uint8_t ap_mac[6] = {0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED};
     uint8_t sta_mac[6] = {0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED};
@@ -213,9 +234,6 @@ class WiFiScan
     // Settings
     uint mac_history_cursor = 0;
     uint8_t channel_hop_delay = 1;
-    bool force_pmkid = false;
-    bool force_probe = false;
-    bool save_pcap = false;
   
     int x_pos; //position along the graph x axis
     float y_pos_x; //current graph y axis position of X value
@@ -232,6 +250,8 @@ class WiFiScan
 
     bool wsl_bypass_enabled = false;
 
+    bool scan_complete = false;
+
     //int num_beacon = 0; // GREEN
     //int num_probe = 0; // BLUE
     //int num_deauth = 0; // RED
@@ -278,6 +298,74 @@ class WiFiScan
       WifiMgmtHdr hdr;
     } wifi_ieee80211_packet_t;
 
+		// Tracking structures for PineScan (similar to MultiSSID)
+    struct PineScanTracker {
+        uint8_t mac[6];
+        bool suspicious_oui;
+        bool tag_and_susp_cap;
+        uint8_t channel;
+        int8_t rssi;
+        bool reported;
+    };
+
+    // For confirmed Pineapple devices
+    struct ConfirmedPineScan {
+        uint8_t mac[6];
+        String detection_type;
+        String essid;
+        uint8_t channel;
+        int8_t rssi;
+        bool displayed;
+    };
+    LinkedList<PineScanTracker>* pinescan_trackers;
+    LinkedList<ConfirmedPineScan>* confirmed_pinescan;
+    bool pinescan_list_full_reported;
+    
+    // Security Conditions For Pineapple detection
+    enum SecurityCondition {
+        NONE = 0x00,
+        SUSPICIOUS_WHEN_OPEN = 0x01,
+        SUSPICIOUS_WHEN_PROTECTED = 0x02,
+        SUSPICIOUS_ALWAYS = 0x04
+    };
+
+    // SuspiciousVendor struct
+    struct SuspiciousVendor {
+        const char* vendor_name;
+        uint8_t security_flags;
+        uint32_t ouis[20];                 // Array of OUIs (max 20 per vendor)
+        uint8_t oui_count;                 // Number of OUIs for this vendor
+    };
+
+    // Declare the table for Pineapple
+    static const SuspiciousVendor suspicious_vendors[];
+    static const int NUM_SUSPICIOUS_VENDORS;
+
+    // Track for AP list limit (Uninitialised, Done in RunSetup)
+    bool ap_list_full_reported;
+
+    // MULTI SSID STRUCTS
+
+    struct MultiSSIDTracker {
+        uint8_t mac[6];
+        uint16_t ssid_hashes[MULTISSID_THRESHOLD];
+        uint8_t unique_ssid_count;
+        bool reported;
+    };
+
+    // New struct for confirmed MultiSSID devices
+    struct ConfirmedMultiSSID {
+        uint8_t mac[6];
+        String essid;
+        uint8_t channel;
+        int8_t rssi;
+        uint8_t ssid_count;
+        bool displayed;
+    };
+    LinkedList<MultiSSIDTracker>* multissid_trackers;
+    LinkedList<ConfirmedMultiSSID>* confirmed_multissid;
+    bool multissid_list_full_reported;
+
     // barebones packet
     uint8_t packet[128] = { 0x80, 0x00, 0x00, 0x00, //Frame Control, Duration
                     /*4*/   0xff, 0xff, 0xff, 0xff, 0xff, 0xff, //Destination address 
@@ -339,6 +427,10 @@ class WiFiScan
       NimBLEAdvertisementData GetUniversalAdvertisementData(EBLEPayloadType type);
     #endif
 
+    void pingScan();
+    void portScan(uint8_t scan_mode = WIFI_PORT_SCAN_ALL);
+    bool isHostAlive(IPAddress ip);
+    bool checkHostPort(IPAddress ip, uint16_t port, uint16_t timeout = 100);
     String extractManufacturer(const uint8_t* payload);
     int checkMatchAP(char addr[]);
     bool beaconHasWPS(const uint8_t* payload, int len);
@@ -383,6 +475,8 @@ class WiFiScan
     void RunGPSNmea();
     void RunMimicFlood(uint8_t scan_mode, uint16_t color);
     void RunPwnScan(uint8_t scan_mode, uint16_t color);
+    void RunPineScan(uint8_t scan_mode, uint16_t color);
+    void RunMultiSSIDScan(uint8_t scan_mode, uint16_t color);
     void RunBeaconScan(uint8_t scan_mode, uint16_t color);
     void RunRawScan(uint8_t scan_mode, uint16_t color);
     void RunStationScan(uint8_t scan_mode, uint16_t color);
@@ -395,6 +489,8 @@ class WiFiScan
     void RunSwiftpairSpam(uint8_t scan_mode, uint16_t color);
     void RunLvJoinWiFi(uint8_t scan_mode, uint16_t color);
     void RunEvilPortal(uint8_t scan_mode, uint16_t color);
+    void RunPingScan(uint8_t scan_mode, uint16_t color);
+    void RunPortScanAll(uint8_t scan_mode, uint16_t color);
     bool checkMem();
     void parseBSSID(const char* bssidStr, uint8_t* bssid);
 
@@ -417,6 +513,10 @@ class WiFiScan
     int8_t min_rssi = 0;
     int8_t max_rssi = -128;
 
+    bool force_pmkid = false;
+    bool force_probe = false;
+    bool save_pcap = false;
+
     String analyzer_name_string = "";
     
     uint8_t analyzer_frames_recvd = 0;
@@ -432,11 +532,20 @@ class WiFiScan
     bool orient_display = false;
     bool wifi_initialized = false;
     bool ble_initialized = false;
+    bool wifi_connected = false;
 
     String free_ram = "";
     String old_free_ram = "";
     String connected_network = "";
 
+    IPAddress ip_addr;
+    IPAddress gateway;
+    IPAddress subnet;
+
+    IPAddress current_scan_ip;
+
+    uint16_t current_scan_port = 1;
+
     String dst_mac = "ff:ff:ff:ff:ff:ff";
     byte src_mac[6] = {};
 
@@ -491,15 +600,18 @@ class WiFiScan
     void RunSetup();
     int clearSSIDs();
     int clearAPs();
+    int clearIPs();
     int clearAirtags();
     int clearFlippers();
     int clearStations();
+    int clearPineScanTrackers();
+    int clearMultiSSID();
     bool addSSID(String essid);
     int generateSSIDs(int count = 20);
     bool shutdownWiFi();
     bool shutdownBLE();
     bool scanning();
-    //void joinWiFi(String ssid, String password);
+    bool joinWiFi(String ssid, String password, bool gui = true);
     String getStaMAC();
     String getApMAC();
     String freeRAM();
@@ -546,6 +658,9 @@ class WiFiScan
     static void activeEapolSnifferCallback(void* buf, wifi_promiscuous_pkt_type_t type);
     static void eapolSnifferCallback(void* buf, wifi_promiscuous_pkt_type_t type);
     static void wifiSnifferCallback(void* buf, wifi_promiscuous_pkt_type_t type);
+    static void pineScanSnifferCallback(void* buf, wifi_promiscuous_pkt_type_t type); // Pineapple
+    static int extractPineScanChannel(const uint8_t* payload, int len); // Pineapple
+    static void multiSSIDSnifferCallback(void* buf, wifi_promiscuous_pkt_type_t type); // MultiSSID
 
     /*#ifdef HAS_BT
       enum EBLEPayloadType

esp32_marauder/esp32_marauder.ino

@@ -34,7 +34,7 @@ https://www.online-utility.org/image/convert/to/XBM
 #endif
 #include "Buffer.h"
 
-#ifdef MARAUDER_FLIPPER
+#ifdef HAS_FLIPPER_LED
   #include "flipperLED.h"
 #elif defined(XIAO_ESP32_S3)
   #include "xiaoLED.h"
@@ -105,7 +105,7 @@ CommandLine cli_obj;
   AXP192 axp192_obj;
 #endif
 
-#ifdef MARAUDER_FLIPPER
+#ifdef HAS_FLIPPER_LED
   flipperLED flipper_led;
 #elif defined(XIAO_ESP32_S3)
   xiaoLED xiao_led;
@@ -123,7 +123,6 @@ const String PROGMEM version_number = MARAUDER_VERSION;
 
 uint32_t currentTime  = 0;
 
-
 void backlightOn() {
   #ifdef HAS_SCREEN
     #ifdef MARAUDER_MINI
@@ -166,10 +165,10 @@ void setup()
   #endif
   
   backlightOff();
-#if BATTERY_ANALOG_ON == 1
-  pinMode(BATTERY_PIN, OUTPUT);
-  pinMode(CHARGING_PIN, INPUT);
-#endif
+  #if BATTERY_ANALOG_ON == 1
+    pinMode(BATTERY_PIN, OUTPUT);
+    pinMode(CHARGING_PIN, INPUT);
+  #endif
   
   // Preset SPI CS pins to avoid bus conflicts
   #ifdef HAS_SCREEN
@@ -193,6 +192,14 @@ void setup()
 
   Serial.println("ESP-IDF version is: " + String(esp_get_idf_version()));
 
+  #ifdef HAS_PSRAM
+    if (psramInit()) {
+      Serial.println("PSRAM is correctly initialized");
+    } else {
+      Serial.println("PSRAM not available");
+    }
+  #endif
+
   #ifdef HAS_SCREEN
     display_obj.RunSetup();
     display_obj.tft.setTextColor(TFT_WHITE, TFT_BLACK);
@@ -258,18 +265,9 @@ void setup()
   buffer_obj = Buffer();
   #if defined(HAS_SD)
     // Do some SD stuff
-    if(sd_obj.initSD()) {
-      #ifdef HAS_SCREEN
-        //display_obj.tft.println(F(text_table0[3]));
-      #endif
-    } else {
+    if(!sd_obj.initSD())
       Serial.println(F("SD Card NOT Supported"));
-      #ifdef HAS_SCREEN
-        //display_obj.tft.setTextColor(TFT_RED, TFT_BLACK);
-        //display_obj.tft.println(F(text_table0[4]));
-        //display_obj.tft.setTextColor(TFT_CYAN, TFT_BLACK);
-      #endif
-    }
+
   #endif
 
   #ifdef HAS_SCREEN
@@ -296,7 +294,7 @@ void setup()
   #endif
 
   // Do some LED stuff
-  #ifdef MARAUDER_FLIPPER
+  #ifdef HAS_FLIPPER_LED
     flipper_led.RunSetup();
   #elif defined(XIAO_ESP32_S3)
     xiao_led.RunSetup();
@@ -352,7 +350,7 @@ void loop()
     #endif
   #endif
 
-  #ifdef HAS_ILI9341
+  #if (defined(HAS_ILI9341) && !defined(MARAUDER_CYD_2USB))
     #ifdef HAS_BUTTONS
       if (c_btn.isHeld()) {
         if (menu_function_obj.disable_touch)
@@ -397,7 +395,7 @@ void loop()
       menu_function_obj.main(currentTime);
     #endif
   }
-  #ifdef MARAUDER_FLIPPER
+  #ifdef HAS_FLIPPER_LED
     flipper_led.main();
   #elif defined(XIAO_ESP32_S3)
     xiao_led.main();

esp32_marauder/flipperLED.cpp

@@ -1,5 +1,7 @@
 #include "flipperLED.h"
 
+#ifdef HAS_FLIPPER_LED
+
 void flipperLED::RunSetup() {
   pinMode(B_PIN, OUTPUT);
   pinMode(G_PIN, OUTPUT);
@@ -58,4 +60,6 @@ void flipperLED::offLED() {
 
 void flipperLED::main() {
   // do nothing
-}
+}
+
+#endif

esp32_marauder/flipperLED.h

@@ -8,10 +8,6 @@
 
 #include <Arduino.h>
 
-#define B_PIN 4
-#define G_PIN 5
-#define R_PIN 6
-
 extern Settings settings_obj;
 
 class flipperLED {

esp32_marauder/lang_var.h

@@ -103,7 +103,9 @@ PROGMEM const char text1_59[] = "Station Sniff";
 PROGMEM const char text1_60[] = "Clear Stations";
 PROGMEM const char text1_61[] = "Select Stations";
 PROGMEM const char text1_62[] = "Deauth Targeted";
-
+PROGMEM const char text1_63[] = "Detect Pineapple";
+PROGMEM const char text1_64[] = "Detect MultiSSID";
+PROGMEM const char text1_65[] = "Select probe SSIDs";
 
 //SDInterface.cpp texts
 PROGMEM const char text2_0[] = "Error, could not find update.bin";
@@ -179,12 +181,14 @@ PROGMEM const char text4_44[] = " AP Scan ";
 PROGMEM const char text4_45[] = "Clearing Stations...";
 PROGMEM const char text4_46[] = "Stations Cleared: ";
 PROGMEM const char text4_47[] = "Targeted Deauth";
+PROGMEM const char text4_48[] = " Detect Pineapple ";
+PROGMEM const char text4_49[] = " Detect MultiSSID ";
 
 //Making tables
 PROGMEM const char *text_table0[] = {text0_0,text0_1, text0_2, text0_3, text0_4, text0_5, text0_6, text0_7, text0_8};
-PROGMEM const char *text_table1[] = {text1_0,text1_1,text1_2,text1_3,text1_4,text1_5,text1_6,text1_7,text1_8,text1_9,text1_10,text1_11,text1_12,text1_13,text1_14,text1_15,text1_16,text1_17,text1_18,text1_19,text1_20,text1_21,text1_22,text1_23,text1_24,text1_25,text1_26,text1_27,text1_28,text1_29,text1_30,text1_31,text1_32,text1_33,text1_34,text1_35,text1_36,text1_37,text1_38,text1_39,text1_40,text1_41,text1_42,text1_43,text1_44,text1_45,text1_46,text1_47,text1_48,text1_49,text1_50,text1_51,text1_52,text1_53,text1_54,text1_55,text1_56,text1_57,text1_58,text1_59,text1_60,text1_61,text1_62};
+PROGMEM const char *text_table1[] = {text1_0,text1_1,text1_2,text1_3,text1_4,text1_5,text1_6,text1_7,text1_8,text1_9,text1_10,text1_11,text1_12,text1_13,text1_14,text1_15,text1_16,text1_17,text1_18,text1_19,text1_20,text1_21,text1_22,text1_23,text1_24,text1_25,text1_26,text1_27,text1_28,text1_29,text1_30,text1_31,text1_32,text1_33,text1_34,text1_35,text1_36,text1_37,text1_38,text1_39,text1_40,text1_41,text1_42,text1_43,text1_44,text1_45,text1_46,text1_47,text1_48,text1_49,text1_50,text1_51,text1_52,text1_53,text1_54,text1_55,text1_56,text1_57,text1_58,text1_59,text1_60,text1_61,text1_62,text1_63,text1_64, text1_65};
 PROGMEM const char *text_table2[] = {text2_0,text2_1,text2_2,text2_3,text2_4,text2_5,text2_6,text2_7,text2_8,text2_9,text2_10,text2_11,text2_12,text2_13,text2_14};
 PROGMEM const char *text_table3[] = {text3_0,text3_1,text3_2,text3_3,text3_4,text3_5};
-PROGMEM const char *text_table4[] = {text4_0,text4_1,text4_2,text4_3,text4_4,text4_5,text4_6,text4_7,text1_54,text4_9,text4_10,text4_11,text4_12,text4_13,text4_14,text4_15,text4_16,text4_17,text4_18,text4_19,text4_20,text4_21,text4_22,text4_23,text4_24,text4_25,text4_26,text4_27,text4_28,text4_29,text4_30,text4_31,text4_32,text4_33,text4_34,text4_35,text4_36,text4_37,text4_38,text4_39,text4_40,text4_41,text4_42,text4_43,text4_44,text4_45,text4_46,text4_47};
+PROGMEM const char *text_table4[] = {text4_0,text4_1,text4_2,text4_3,text4_4,text4_5,text4_6,text4_7,text1_54,text4_9,text4_10,text4_11,text4_12,text4_13,text4_14,text4_15,text4_16,text4_17,text4_18,text4_19,text4_20,text4_21,text4_22,text4_23,text4_24,text4_25,text4_26,text4_27,text4_28,text4_29,text4_30,text4_31,text4_32,text4_33,text4_34,text4_35,text4_36,text4_37,text4_38,text4_39,text4_40,text4_41,text4_42,text4_43,text4_44,text4_45,text4_46,text4_47,text4_48,text4_49};
 
 #endif

esp32_marauder/utils.h

@@ -4,6 +4,11 @@
 
 #include <Arduino.h>
 #include <vector>
+#include <WiFi.h>
+
+#include "configs.h"
+
+#include "esp_heap_caps.h"
 
 struct mac_addr {
    unsigned char bytes[6];
@@ -13,6 +18,13 @@ struct Station {
   uint8_t mac[6];
   bool selected;
   uint16_t packets;
+  uint16_t ap;
+};
+
+struct ProbeReqSsid {
+    String essid;
+    bool selected;
+    uint8_t requests;
 };
 
 const char apple_ouis[][9] PROGMEM = {
@@ -144,6 +156,35 @@ const char xiaomi_ouis[][9] PROGMEM = {
   "90:4E:91", "C4:0B:CB", "D0:DB:32"
 };
 
+uint8_t getDRAMUsagePercent() {
+  //size_t total = heap_caps_get_total_size(MALLOC_CAP_8BIT);
+  //size_t free = heap_caps_get_free_size(MALLOC_CAP_8BIT);
+  size_t free = ESP.getFreeHeap();
+  size_t total = ESP.getHeapSize();
+  
+  if (total == 0) return 0; // Avoid division by zero
+
+  size_t used = total - free;
+  uint8_t percent = (used * 100) / total;
+  return percent;
+}
+
+#ifdef HAS_PSRAM
+  uint8_t getPSRAMUsagePercent() {
+    //size_t total = heap_caps_get_total_size(MALLOC_CAP_SPIRAM);
+    //size_t free  = heap_caps_get_free_size(MALLOC_CAP_SPIRAM);
+
+    size_t total = ESP.getPsramSize();
+    size_t free = ESP.getFreePsram();
+
+    if (total == 0) return 0; // Avoid division by zero or PSRAM not available
+
+    size_t used = total - free;
+    uint8_t percent = (used * 100) / total;
+    return percent;
+  }
+#endif
+
 String byteArrayToHexString(const std::vector<uint8_t>& byteArray) {
   String result;
 
@@ -316,4 +357,33 @@ String replaceOUIWithManufacturer(const char *sta_addr) {
   return String(manufacturer) + mac_suffix;
 }
 
+IPAddress getNextIP(IPAddress currentIP, IPAddress subnetMask) {
+  // Convert IPAddress to uint32_t
+  uint32_t ipInt = (currentIP[0] << 24) | (currentIP[1] << 16) | (currentIP[2] << 8) | currentIP[3];
+  uint32_t maskInt = (subnetMask[0] << 24) | (subnetMask[1] << 16) | (subnetMask[2] << 8) | subnetMask[3];
+
+  uint32_t networkBase = ipInt & maskInt;
+  uint32_t broadcast = networkBase | ~maskInt;
+
+  uint32_t nextIP = ipInt + 1;
+
+  if (nextIP <= networkBase) {
+    nextIP = networkBase + 1;
+  }
+  if (nextIP >= broadcast) {
+    return IPAddress(0, 0, 0, 0); // no more IPs
+  }
+
+  return IPAddress(
+    (nextIP >> 24) & 0xFF,
+    (nextIP >> 16) & 0xFF,
+    (nextIP >> 8) & 0xFF,
+    nextIP & 0xFF
+  );
+}
+
+uint16_t getNextPort(uint16_t port) {
+  return port + 1;
+}
+
 #endif

pictures/xbm/force_16.xbm

@@ -0,0 +1,6 @@
+#define 3f9b97ac7933453c85ec3a8adb49feeejQ9bt0wTgiC65w8g_width 16
+#define 3f9b97ac7933453c85ec3a8adb49feeejQ9bt0wTgiC65w8g_height 16
+static char 3f9b97ac7933453c85ec3a8adb49feeejQ9bt0wTgiC65w8g_bits[] = {
+  0xFF, 0xFF, 0x1F, 0xF8, 0x0F, 0xF0, 0x07, 0xE0, 0x07, 0xE0, 0x07, 0xE0, 
+  0x67, 0xE6, 0x77, 0xEE, 0x87, 0xE0, 0x8F, 0xF1, 0x0F, 0xF0, 0x4F, 0xF5, 
+  0x1F, 0xF8, 0x3F, 0xFC, 0xFF, 0xFF, 0xFF, 0xFF, };

pictures/xbm/joined_16.xbm

@@ -0,0 +1,6 @@
+#define 67ae760eaaa64924c492c46151d37f46mewyG1NBArKDOITT_width 16
+#define 67ae760eaaa64924c492c46151d37f46mewyG1NBArKDOITT_height 16
+static char 67ae760eaaa64924c492c46151d37f46mewyG1NBArKDOITT_bits[] = {
+  0xFF, 0xFF, 0xFF, 0xFF, 0x07, 0xFF, 0xFF, 0xFC, 0xFF, 0xF3, 0x87, 0xF7, 
+  0x7F, 0xEE, 0xFF, 0xED, 0xC7, 0xDD, 0xBF, 0xDB, 0x7F, 0xDB, 0x67, 0xDB, 
+  0x67, 0xDB, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, };

pictures/xbm/pineapple_22.xbm

@@ -0,0 +1,9 @@
+#define be52a82b6ef24281d57d9491aef1484cv5n1Pq988C5WdKha_width 22
+#define be52a82b6ef24281d57d9491aef1484cv5n1Pq988C5WdKha_height 22
+static char be52a82b6ef24281d57d9491aef1484cv5n1Pq988C5WdKha_bits[] = {
+  0xFF, 0xFF, 0x3F, 0xFF, 0xF7, 0x3F, 0x7F, 0x96, 0x3F, 0xFF, 0xED, 0x3F, 
+  0x3F, 0x25, 0x3F, 0xDF, 0xD2, 0x3E, 0xFF, 0xED, 0x3F, 0x7F, 0x8E, 0x3F, 
+  0x3B, 0x77, 0x37, 0xBD, 0x6A, 0x2F, 0xD6, 0xBD, 0x1A, 0xDA, 0xDA, 0x16, 
+  0x5A, 0x6F, 0x16, 0x9A, 0xF7, 0x16, 0xD6, 0x5A, 0x1A, 0xDD, 0xBD, 0x2E, 
+  0xBB, 0x5A, 0x37, 0x3F, 0x6F, 0x3F, 0x7F, 0xB7, 0x3F, 0xFF, 0xCC, 0x3F, 
+  0xFF, 0xF3, 0x3F, 0xFF, 0xFF, 0x3F, };